Видео

I need help! I have a Flysky I6X transmitter to control my tracked inspection bot. But when I first switch the transmitter on, it beeps and gives me this message: "!!WARNING!! Place all switches in their up position and lower the throttle" Sometimes I just bump my left toggle switch, channel 3, and it stops the warning and gives me full control. But all too often, it doesn't matter how many switches and toggles I move around, it just keeps beeping and will not give me control. What is it doing and how do I get it to stop? I have a simple tank chassis with a light and camera gimble on it. It's not like I need a safety switch to start with. Can you help me?

Hi why is it my menu not showing up?!!!! Thks.

When I push up it goes left down goes right whats happening 😫

Hi. My quadcopter motors are not rotating uniformly ie(1st motor starts to rotate at 20%throttle 2nd at 40% 3rd at 60% 4th at 75%) what to da?

I need a flysky

Whyyyyy 1100 1900 hundred??

I already reached the limit of the subtrim bar and still haven't reached 1500, how can I fix that?

Hello sir i have rcb6i avionics rc, in my rc rudder not going to min and max value position so that i am not able to arm Quadcopter. What should I do to set min and max position?

Could you explain what the percentages correlate with? We are new to this and having issues with the pitch of our plane reach the correct amount. The servo moves far on the lower end point, but not at all towards the top end point.

Thanks for mentioning the trim...They had gotten messed up somehow..wow..blinking (ARM not) red light gone and values reasonable.

LIFE SAVER! Thanks a lot for sharing this crucial piece of information.

It's G.U.I ( graphical user interface) not goeey

Hello how do you make sure your trims are centered before you start subtirming

Hi my friend my. transmitters flysky fsi6, PPM is getting throtle and yaw commands when I connect but there is no movement on the pitch and roll side, what is the problem of working aux?

hello can u help me how to setup a 450 clone heli with the i6 transmitter with A8s receiver

I set mine to 1k and 2k and it feels like the throttle max, flips, and rolls are so far away from the center. I'm guessing going 11 and 19 would shorten that up? does any one know?

with the endpoints how do you change them if using a switch? (i can only change the first endpoint percentage, i need to change the second??)

can i use this on an rc tank?

Hi. Why we should set up 1100 low and 1900 max?

only 3 chanel motor runs 1 2 4 are not working plzzz help me.aney suggesions

does this work on betaflight?

Its GEEYOUEYE GUI, not GOOEY! XD

Do you know how to change the endpoint a on a fly sky th9x? I can't seem to change channel 5, 7 & 8 no matter what switches I move.

my end points and subtrim keep changing. any help?

Thanks, I thought I'd tried everything, but not the Roll right!

hey i haven't done this mod yet, but has anyone got it to work with betaflight? I'm pretty sure i have my pwm channels set up right and i already binded the tx to the rx, but i cant get it to move the channels on the betaflight configurator.

can you reverse the channels in the transmitter im planing to build a pop wing and i already know that ch1 will need to be reversed

I think I needed this video for my transmitter tuning. It may fix my yaw problem. I'll test it out tomorrow.

Very useful. Did not know how to switch from low to high. I'm currently having issues with arming the Naze and this video has given me a direction. I had been messing around with trims and sub trims and was about to reset the Tx. I think this is what I need. Thank you!

arming the quad was my problem/. Thank You Huge!

Ok, thanks for the video. I have a couple questions. I have the fs-i6 and fs-ia6 running on my new (not yet finished) 180, and when I plug it into cleanflight it shows the throttle and yaw as the same thing, I don't believe that's right, but it is my first maiden, so I could be wrong. Also when I turn it on, and the motors are running, ill flick the pitch up and then flick back into position, but their is a noticeable change that happens when I do this in listening to the motors. I'm not sure what's wrong, please help.

and how do u Change assignment of the pitch, yaw exe

how do u set these for a cc3d or is it the same values

Thank you so much. I couldn't figure out how to get on the the second column of end points. Was driving me crazy. Big help. Cheers!

great vid. good job