Видео

I cant really say because it depends on how often your using them . If your using them daily id say your probably better off buying high quality thicker ones. If its a few times a month then you'll get good use out of them.

@@mbtoolreviews much appreciated, brother.

Yeah i was rushing a bit too much . Thankfully i managed to fix it and its pretty close to the factory edge definitely good enough to use again. I need to post the repair.

@@mbtoolreviews Well i bet now u done it once you will never do it again, best way to learn is by making the odd mistake. Respect the router though them things want to hurt you.

Yeah thats a lesson learnt.

I'll have to look in to that and ill try post a video thanks for letting me know.

These are hydraulic so i dont think there is any motor or if there is i havent seen anything to say brushed or brushless. Sorry i cant be of more help . Also i think ACO103 is the only one which swivels the older ones dont . Thanks for watching.

As far as i am aware no . None of the maufacturers of these have replacement blades .

Yeah these are a great little drill for the small jobs i have had a few issues with the batteries staying charged both otherwise a great tool. Thanks for watching.

i also love tools ... probably too much 😅. Thanks for watching

There are some slight differences. The new handle the bar for pushing the glue has a different handle and i think its slightly lighter. I havent used it but just from pictures thats all i can tell.pretty much the same tool.

@@mbtoolreviews thanks ((:

I think im going to have to look into that i want to get a cyclone setup for big woodworking jobs.

Is that the 3M mask ?

@@mbtoolreviews Yes and no,model is a 3M but they are made in china by everyone.Most of the time on picture it will be 3m but in reality you get some no name brand. I had one made by Dainu from banggood and it worked fine for several years before rubber started to smell funny . So it may not be 3m but it doesnt mean its necessarly a bad quality. Since i am using mask 99% of time for dust i use 3200 now.Its a cheap copy made of silicone but it works flawlessly and filters are super cheap+you can wash filters 4-5 times before you throw them out.

Im very skeptical about using these sites for safety wear. If i can find a way to test it i might compare ut to my jsp mask .

I was replacing a set of taps the other day and i only brought the nerrad with me and i kept getting the handle stuck. I was wishing i had the TT with me aswell . I think there both great kits i do agree though the price is too much for the nerrad.

No sorry i actually only really use them on screws and band strap and stuff . I would definitely go with the biggest size u can afford and want to carry just for leverage. Becuase anything repetetive is gonna be tough even with these. Hope that hepls thanks for watching.

Hope you like it . i find mine very useful and thanks for watching.

Hi Christine, this is a 2 part glue so im not sure what your using it on . If you are able to give some context i might be able to help . However c a glue can usually be cleaned off with acetone or rubbing alchohol but with pvc you may want to try a test area is acetone can also disolve it . Hope that helps thanks for watching.

I must have overlooked that thanks for letting me know .

Hi i had a look at the gebrit and like you said it looks identical and the model numbers line up. Before the ac103 the other novo press guns didn't swivel. Maybe its novopress specific. On mine it just swivels by hand no button needed. Thanks for watching.

@mbtoolreviews I'm starting to think it must me! My friend also has the same model as me, and his doesn't swivel either. What a shame, considering their identical in every other way.

You can buy different jaws v press or m but as this is the same as the milwaukee version the pex jaws should be available for it . If not there are some other press fit that do pex. Thanks for watching.

In the uk they are around £1300 to £1800 for this model depending on the heads, for other press fit machines it’s £800 up to maybe £2000 with heads and attachments. Thanks for watching.

Yes they are. Thanks for watching.

Ill have to double check that and get back to you .

It doesn’t so this is hardly a review.

To answer your question, Yes it does fit the trim base if you use the lock ring but not the adapter plate thats for the plunge base. It is a bit of a pain to fit if you have the dust guard on. If you would like i can post a short video showing its install. Thanks for watching

No , I wasn't too worried about contamination as any residual grit or burrs should wash away with the lubricant . But even if it didn't, im not particularly fussed as long as my chisels come out sharp at the end.im still fairly new at sharpening, so that might be a bit more of a pro level question. Thanks for watching.

@@mbtoolreviews sorry, I wasn't very clear. What I meant was that some cheap diamond stones, especially dual sided ones have grit contamination during their manufacturing process, where coarser particles will be embedded on the finer grit plates. You can see that with the scratch pattern basically remaining the same when you go up in grit. I am trying to get a real 1000 grit diamond stone, but I didn't see any review that looked into that and found a "true" 1000 stone

​@@Aexium I think that's mostly a problem with the dual sided ones, since they go through the same lines, so coarse particles get into the fine side. Always go for the single sided diamond grits. I'm going to give one of these a try just for fun and maybe a gift to my brother that bought a super steel knife without a good way to sharpen it. I'll grab a DMT Fine if this is toast, although I might just do it anyways.

@@mikafoxx2717 yeah, I know, but these plates are so cheap it's hard to not be concerned

I think they are the same, tool theres quite a few different brands but if you look at them they all look identical. I was going to get the quick wire but i went with c.k. because ive use a lot of there stuff before. Thanks for watching.

No problem, thank you for watching.

Using the bracket u could use those sticky hooks that peel off or the base has magnets that you can stick to a metal surface . Thanks for watching.

Glad to help thanks for watching

I bought them on amazon and i think you can get them on ebay aswell.

No problem , thanks for watching.

No problem , ive got a video on parrallel guides for tracksaws coming out in the next few days so keep an eye out.

@@mbtoolreviews nice one. I've subscribed so I'll get a notification. Cheers pal.

No problem ,thanks for watching .

🤣 wow love the expert analasis there . I am most definitely a man of the tools but yes your right I shouldn't be using leverage to my advantage thanks.

Youll need both a wrench for the tap connector and back nut. This set does both and has 2 bars or can be used on the rachet or a screwdriver head with the same connections. Failing that you could use one of the adjustable basin wrenches with telescopic arm but this set costs about the same .hope this was of some help thanks for watching.

@@mbtoolreviews Thank You!!

Im not quite good enough at keeping the angle right free hand so i need the guide 🤣. Thanks for watching.

@@mbtoolreviews same i am just too lazy to buy a guide

Hi it doesnt do imact although it does look like one this is strictly a drill with multiple attachments. it doesnt have the torque of an impact hope that helps .thanks for watching.

Stay tuned i have a part 2 coming

Hi gareth , thanks for the comment .i actually did a video on this just after the review. i use the soap method now have been for a little while and i agree i does give a much better result. Thanks for watching.

Yeah it wasnt actually one of my chisels i got it off a freind it was all banged up and i thought it might be interesting to gove it a go. I would say if you have and chips or dings like the one in the video, it's best to grind the 25 degree until there all gone then add your 30 degree micro bevel on a perfect surface. I probably rushed it a bit at the end so i dont think i got them all out , but it was really just for fun . Also thanks for the tip and thank you for watching, hope it was some help.

@@mbtoolreviews - Certainly does help. I chose your video mainly based on the Amazon items I've been looking at, those diamond stones in among them.

The video was just my opinion and a test. i am by no means a pro at siliconing, i can get a nice bead but not anywhere near as fast or as good as you guys . Thank you for your tips I'll try them out they are very much appreciated and thank you for watching.👍

@@mbtoolreviews Totally understand this was just meant as information not criticism

Thank you no criticism taken 100 percent appreciate the guidance.

No problem glad to have helped

Where did you find t25 and t100 ? is it on their packaging? i haven't heard of it but if you can tell me where you saw it ill try to explain. If your reffering to the ink i just bought marker pen replacement ink any type of marker ink should do.

@@mbtoolreviews that was lightning fast reply, thanks. I googled some random permanent marker ink refills and came across different types. T25 and t100 were on the bottles. Maybe T is for thickness?