- Видео 76
- Просмотров 63 076
Hoovercamaro
Добавлен 3 апр 2014
I don't talk about the Camaro much, but Check out some of the junk in the driveway, barn, shed, garage and shop in a Small Town in Southern Ontario Canada, Maybe you'll see something cool, learn something new with me, or find a use for one of those bolts you've been saving in a Folgers can for 10 years, too bad i didn't save 3 more of that size...
1950 Farmall H
Diagnosing Burnt Ignition points due to bypassed Resistor on 1950 Farmall H
Просмотров: 126
Видео
1972 Bombardier Ski Doo Olympic and 1979 Everest 500 Electro
Просмотров 156Месяц назад
Two New Project Sleds In the middle of summer, a 1972 Olympic 300 and a 1979 Everest 500, More Videos on these to Come
2020 Cub Cadet Spring 2024 Maintenance
Просмотров 1403 месяца назад
Time to look over The Cub Cadet Zero Turn mower before putting it to work for the season
Craftsman Push Mower
Просмотров 2773 месяца назад
Here's an old video i took and Forgot about, i tried editing it as best i could, sorry i didn't get a Video of it running later on.
1996 Yamaha 20 hp Two Stroke Outboard
Просмотров 1154 месяца назад
This startup is after i drained all the old gas out of lines and carbs and got the engine warmed up after sitting in the barn all winter, it has a dual carb setup with an oil Injection system.
The 400's Sticky Recoil
Просмотров 1035 месяцев назад
took a Pull pulls to Get Her going but she's Quick on the Snow
2009 Impala Front Wheel Bearing
Просмотров 976 месяцев назад
replacing the front Passenger side Wheel hub Assembly on a 2009 Chevrolet Impala LS Fromt wheel Drive
O2 Sensors 2009 Gmc Sierra
Просмотров 1426 месяцев назад
Bad DownDraft Oxygen Sensor in 2009 GMC Sierra 1500 4.8L Vortec
New Steering, things are coming along
Просмотров 3858 месяцев назад
New Steering, things are coming along
Video Tour of the Canadian Drilling Rig Museum
Просмотров 85Год назад
Video Tour of the Canadian Drilling Rig Museum
6 Cylinder Case Engine run on Natural Gas
Просмотров 58Год назад
6 Cylinder Case Engine run on Natural Gas
You Never Know What you're going to Find in the Barn
Просмотров 14Год назад
You Never Know What you're going to Find in the Barn
Wish I watched this video before doing mine. Linestogo video sucked
gotta love the jd cheese wedge. also didnt know they came with turbos 😂
Hey great video and also I just want to give a suggestion that maybe try posting it as a RUclips short since the video is only 30 seconds long it most likely will get pushed out to more people and get you some more subscribers on RUclips
Thanks, I just post videos for fun, can't Make any money from social Media in Canada anyways lol
That’s such a nice tractor! Gotta love IH equipment!
Начало российского бурана😅
This was the Last Snow of Winter in Southern Ontario Canada
Hammer fixes everything. That fan sounds like a jet plane.
😂 Can't go through life without at least one Rubber mallet
Well done ! I guess some heat really helps eh.
Sure Wish we Had an oxy/Acetylene Torch, but the bottle of map helped.
Better take a harness with you on long haul. Dogs can help pull her home.
😂 She Ain't Leaving the Farm, not with the Price of Insurance and Gas these days!
She's a runner boy!
Might be time to move to an aftermarket CDI setup.
😂 naw she's runnin good now
please normalize your mic, cannot hear you clearly. Cool project though wish i could have watched it.
Using a Junky Old Cellphone if you really wanna watch you'll have to fight through the Horrible audio lol.
Ride it!
Ain't Got snow
In my opinion with all the problems the deeres had with the cdi boxes failing, tge points are a superior system. Tge kiortz ccw engine is a great engine
In my opinion with all the problems the deeres had with the cdi boxes failing, tge points are a superior system. Tge kiortz ccw engine is a great engine
CCW is a great engine. After putting a Mikuni carb on mine it runs great.
Great sled ,with very little rust on the tunnel .
She's mostly Aluminum lol
Your shifter fork probably needs to be looked at, keep her going
The transmission has had a Mind of its Own for the past 50 years, wouldn't be as much of a challenge if i fixed it now lol😂
Great video!now I understand why your farmall H doesn’t like the snowblower . I have a 20hp kubota and the PTO is rated at 13hp.Probably not enough for a snowblower. Interesting information about the Ford tractor,I watched one of those burn in a field one time.I always carry a fire extinguisher because of that incident.
I tried to figure out the engine HP from tractor data 2.7 litre or 164 cubic inches ,would you know?
Farmall Super H has 32.2HP at draw bar. According to Nebraska Tractor data. 😊
I'm not sure of the displacement we don't have any specs for the engine since we've never had an issue with it, every website I've looked at has a different horsepower listed unfortunately.
BEAUTIFUL TRACTOR BRINGS BACK WONDERFUL MEMORIES HERE ❤️
Tractor data says your Farmall H has 29 hp at the PTO. Tractor looks in great condition. Thanks
That Could potentially be for an H, This is a Super H Which comes with larger Exhaust valves and a Larger carburetor, my grandfather says the pulley Produces 35 horsepower, not sure what horsepower the power take off puts out.
HI JAMES MY SUPER H IS THIS SAME AS THIS VIDEO IT CAME FROM THE FACTORY WITH 34 HORSEPOWER FROM WHAT I RECALL WE BOUGHT OURS BRAND NEW FROM THE DEALER USED MANY YEARS ON OUR FARM. -SAMUEL
Big John!! 😂
Elmira Farm Service is now known as Premier Equipment. They had a few locations besides Elmira and I believe the name change was because more of their business was no longer in Elmira.
I used muriatic acid on my ski doo to remove the melted aluminum off the cylinder. Worked great. Wonder if you could do that for that cylinder. Don't put it back together like that.
Did a bit of Research, gonna try the Lye method since we've already got some on the farm.
Arrow should point towards exhaust. Deere must have used stainless hardware for those exhaust nuts. They never seem to rust.
Canadian special : Specifications:Notes: Only sold in Canada. Used more aggressive jetting & clutching, Liquifire chaincase, suspension similar to a Liquifire. It came stock with dealer options like tachometer, speedometer, tether switch, remote fuel shut off, handle bar warmers, and sport seat.
Whe I deleted the oil injection on mine I bought some plugs for the bottom of the intake from the hardware store.
I've Already Got a Cheaper solution for plugging the holes lol, just haven't edited the next video yet.
@@hoovercamaro cool
I road dirt bikes when I was a child, of all ages😂. I remember when I was around 10 or 12 I got on a 3 wheeler when they first came out and tried to corner the same way. Needless to say we know what happened and I got right back to 2 wheels.
старые роторы кавасаки имеют проблему с отпадающими магнитами, многим моторам эта поломка стоила перемолотых генераторов, потом кавасаки исправились и стали укладывать магниты в металлическое кольцо, но на старых кавасаки можно по прежнему видеть просто приклеенные магниты, стоит заменить старый ротор на более позднюю версию.
Wonder how that will work replacing the crank seal without splitting the cases.
Try Over The Hill sports look them up for parts they in canada
Thanks for the Suggestion!
You can revive old hard rubber parts by soaking them in brake fluid. Might take a week or more depending on how dry they are.
The carb boots off this sled are a bit too far gone unfortunately, thanks for the suggestion though.
Ah man. She's rough. I want to see it on the snow this season.
After trying to soak the Carbs in Clr, Varsol, Vinegar, and Boiling water im almost certain they're going to need replacing since the Corrosion is so bad.
Mostly what I seen the horse power is on the PTO/belt pulley at least on the Oliver 70 and the John Deere tractors it was the PTO/belt pulley and overall tractor horse power and draw bar horse power
Right on
I HATE that backwards picture crap
Tell Us how you Really Feel 😂
Sounds familiar
That little lever that you're playing with is the draft control
Quite the collection.
It's more of an Addiction, the Red 79 Trailfire 440 is outside with the old Olympic and Nordik
why is the picture backwards.?.
Busted Camera on the Cellphone
I've got a 1950 8N, you'll learn to love that thing. Simple, built solid and easy to fix. There is a reason half of them are still being used today despite being neglected.
This is actually a nice looking 8n. Once you start working on it you'll figure it all out and come to love it. Two things 1. The thing under the gas tank is the Fuel Bowel, which screens out debris 2. The level under the seat is your draft control level. Nice tip on turning the pto shaft to lift the hydraulic arms, not many people know that.
You're not Wrong about the Glass bowl separating out particles, however it's designed to Separate Water from gas, since water settles at the bottom due to it being heavier than Gasoline, allowing you to turn off the fuel valve and dump the water out of the bowl.
It's fortified. Run it.
I wanna Send a Quart of it to @ProjectFarm
can you do a video on the wiring ? working on putting this in a golf cart and can’t figure out my wiring issue just need to see the general wiring
What Kind of Issues are you dealing with?
@@hoovercamaro no spark
lots of loose wire don’t know what goes where
@@behzz2654 if its the Same Model of Kawasaki engine then you can find a Shop Manual With wiring diagram by just Googling it, have you tested the Coils ?
@@behzz2654 if you google ta440 Kawasaki Wiring Diagram google images has a pictorial of all the labelled wires and What colors they are
Your basement looks like a torture dungeon
Its a 160 year old Farmhouse Cellar
The caption makes the entire video
And NOW I know why your clothes get so dirty 🕳😄
Fired up the 1973/3 JD 440 today just got done rebuilding er....she's a runner!😁👍
Nice!
Yo do you know what the two marks to the right of the T mark on the flywheel are??? Denso ignition!
I guess my replies didn't go through, but i believe the T stands for Top Dead Center, im assuming the hash marks mean Pre detonation or they mark the advance in spark as the rpm rises, I'm not the most knowledgeable with things like that but thats just my guess, hope you can find the answers though, what makes you ask?
@@hoovercamaro Well I turned the stator to the first mark to right of T mark on flywheel checked the points opening just as that mark hit the T mark on fan housing....she started right up no hesitation or backfire and good throttle response...so I'm guessing that mark is 10 before tdc...that's where it should be set....just watch the plugs now and see how they burn!😁👍
@@Frank-rx6wm I hope you Gapped the Points right, i can't remember the exact specifications, my grandfather who is 76 gave me a lesson on setting/gapping points he uses his swiss army knife to set then to between 0.010 and 0.015 thousands of an inch, i used a feeler gauge.
@@hoovercamaro as I lined up the marks slid a 14 thou gauge into the points! She's good fired right up no missing no backfire didnt hear any preignition explosions I run it a little bit up to operating temp pull plugs and check the burn....
@@Frank-rx6wm Thats good, I'd drive it around for about an hour to know if it's running right (lacking power, not getting up to top rpm with load or after hot,etc.) but are you you worried about the Timing or air fuel mixture? Should lubricate your carb and spray some wd40 through all the jets, in the needle and seat, and all around the float and float pin.