Видео

Day 12 working on Project Betty the 76 Monarch. This is a short video because it was just to cold in the garage for me to work. I needed more room to work on the passenger side wheel lip than I had. I jacked up the rear of the car and slid it sideways. This gave me twice the room and I need it. Now I will be able to complete this area of the car.

Day 11 working on Project Betty the 76 Monarch. I cut another rusted area out on the passenger side in front of the rear tire. I made a patch and welded it in. After grinding down the welds I added the Duraglas Fiberglass Reinforced Filler.

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 10 working on Project Betty the 76 Monarch. I finish sanding the drivers side Duraglas, fiberglass reinforced filler. I Hammer and Dolly some dents on the passenger side quarter panel. I then cut out some more rust. I bounce around from area to area on Betty working on what I feel lik...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 9 working on Project Betty the 76 Mercury Monarch. Today I decide to re-do the rear wheel lip area. I wasn’t happy with the way it is. The inner edge isn’t parallel to the body line above it. So I add a layer of Duraglas, fiberglass reinforced filler to the inside surface making it pa...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 8 working on Project Betty the 76 Monarch. I make the patch piece for the area between the door and the wheel opening on the drivers side. Once fitted, I weld it in, grind down the welds and apply Duraglas, fiberglass reinforced filler. Dan’s Messy Garage Merch Store: dans-messy-garag...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 7 working on Project Betty the 76 Mercury Monarch. I sand the drivers wheel lip again. Sand behind the tire, clean and seal the metal and cut out the area in front of the tire. I made a couple L braces and figure out how I’ll patch the hole I just cut. Dan’s Messy Garage Merch Store: ...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 6 of working on project Betty the 76 Monarch. I sand down Duraglas, fiberglass reinforced filler. fiberglass reinforced filler on the drivers side wheel lip and start work on the passenger side wheel lip. I make the L shaped piece and when I start to cut the metal away to install it I...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 5 Working on Project Betty. I weld in the drivers side wheel lip pieces. I grind all the welds and apply the first round of Duraglas, fiberglass reinforced filler. Dan’s Messy Garage Merch Store: dans-messy-garage.myspreadshop.com

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 4 working on Project Betty the 76 Mercury Monarch. Today I cut away the rust over the drivers side rear tire. I make custom L shaped pieces that will be welded in the wheel lip area. Dan’s Messy Garage Merch Store: dans-messy-garage.myspreadshop.com

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I went in the garage today to apply the second coat of POR 15. First I poured some alcohol in the trough to check for leaks. I found 3 of them. I applied more fiberglass cloth and POR 15 to the leaking areas. Dan’s Messy Garage Merch Store: dans-messy-garage.myspreadshop.com

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I use a POR 15 Rust Stop Kit on Project Betty’s rear window trough. I used the Cleaner/Degreaser and then the Metal Prep to treat the area prior to applying the POR 15. I put some fiberglass cloth over the couple holes I saw. This will seal all leaks for good. Dan’s Messy Garage Merch Sto...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I fight to remove the old rear bumper cover on a 78 Mustang II so I can replace it with a new one. I couldn't figure out how it was attached. It was a struggle and I ended up ripping and cutting it off. New bumper was a bolt on. I installed the blue bumper guards and will leave the bumper...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift My speedometer cable was making noise. I tried to pull the cable insert from either end but it was bad. I ended up breaking the cable at the trans. I bought a new cable and replace it in this video. Dan’s Messy Garage Merch Store: dans-messy-garage.myspreadshop.com

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I make simple backers to raise my seat 2” plus move it back 1” gf or more leg room. I weld two pieces of 1” angle iron together, drill holes and test fit in the car. They work great. Now I just need to reinforce them and paint them flat black. Dan’s Messy Garage Merch Store: dans-messy-ga...