- Видео 316
- Просмотров 228 266
Rafi Automation
Объединенные Арабские Эмираты
Добавлен 24 окт 2020
Видео
Masha Allah How Chick Come Out From The Egg
Просмотров 910 месяцев назад
Masha Allah How Chick Come Out From The Egg
شہزاد اکبر، زلفی بخاری اور فرح گوگی کے اثاثے منجمد کرنے کا حکم
Просмотров 6Год назад
شہزاد اکبر، زلفی بخاری اور فرح گوگی کے اثاثے منجمد کرنے کا حکم
ACH580 Fault External Temperature too High
Просмотров 296Год назад
ACH580 Fault External Temperature too High
How can we clean this smalls flaconts please ? After testing in the end of operation
How can we clean this smalls flaconts please ? After testing in the end of operation
How can we clean this smalls flacont
How to calibrate for buffer sulution
Bro you should make video to proper all chemicals testing CL, PH, CYA,ALKA,CAH, I need to know how to test all chemicals.
Check i have all in other videos
❤ nice
Thank u
What do I do if it keeps saying sequence failed?
Very nice dear
My controller only showing pause in the digital display. Both chlorine and ph pumps are not dosing because of the pause. Any reference
Remove the pumps and sensor wires and pn the controller
O Bhai URDU hindi bolo. kuch samjh b aye
Hello when we are keep set point cl 2ppm why it's going 3ppm, Please let me know
❤❤❤
Nice explained..
Helpful video
Helpful video
Water indicater blinking red and green. What it means and steam is not generated now.
Verry nice dear
Do you have chiller control programming using plc
Yes
Nice information
😮😮😮
I support u
Nice video❤❤❤
Tanx u❤
U welcome
Sir, I want to ask about the UPS S 8 problem. If the power source is off, why is the UPS also off? Why can't automatically back up? Even though the battery status is normal, it's full.
What company and model ups do use. what is the capacity of ups
Sir, I want to ask about the UPS problem... if the power source is off, why is the UPS also off? Why can't it automatically back up? Even though the battery status is normal, it's full.
What company ups are you using. It must be in online mode and auto mode. If can tell me what model and company ups do u have i can asdit you with proper instructions.
What company ups are you using. It must be in online mode and auto mode. If can tell me what model and company ups do u have i can asdit you with proper instructions.
How to open the door if there is a dead battery?
If battery is dead u can use the same program to open coonect laptop or programming device for few minutes and then give open command. if the lock actuator is having issue then u have to cut the main bolts to open the door ruclips.net/video/j8poaPTBbGo/видео.html See the link
If battery is dead u can use the same program to open coonect laptop or programming device for few minutes and then give open command. if the lock actuator is having issue then u have to cut the main bolts to open the door.
If battery is dead u can use the same program to open coonect laptop or programming device for few minutes and then give open command. if the lock actuator is having issue then u have to cut the main bolts to open the door.
With regards and respect to your service In ABB inverter model ACS580 we have error 6581 During continuous operation, it gives this error every three hours, and in case of fault, the inverter is turned off. please guide me Of course, it goes without saying that we have also done a factory reset Thank you
Hi
Hi
Good 😊
Sir how to set a time morning 4 am to evening 4 pm
Check video and you have to use two programs one program and off program
@@rafiautomation like program #1 for on the system and program #2 for off the system
Thanks buddy, do you know how to fix Earth Leaking fault?
Your drive showing earth leakage fault
@@rafiautomation how fix that
I would like to contact you please
Hi my fan 2 dose not turn on do I have to activate ch4 on After fan on ch 1,2,3 the fan 2 does not flashing
Aponar numberta dan
informatic Video
What is the “START-UP KEY”?
I have 30 new pcs alerton 1600 if someone interested
I want to know the torque increase in the device 1:54
The voltage drop down ,then motor not running good,what is problem of my inverter..
Can you give an idea for my probem
Can you tell me what is the meximum voltage ur vfd reach and then its drop to what value. What is the frequency when the voltage start drop
☆☆☆☆☆
Sir you are not upload alerton bcm how to reset.
I have alerton vlc 1600 vav sd and 444 abd other
Ok but what does the value correspond to, is it good or bad ?
Great information, I would like to be assisted on how to determine and set the right overload protection component, or how to calculate the overload that I should be set. Thanks in advance
Crush the tablet or let it dissolve for 2mins, otherwise you'll get lower cl value than it is in the water.. also wipe the glass for fingerprints, not only for water 🙂
This is one stage only is right? If chiller not achieved common supply temperature how you will run 2nd or 3rd chillers can You make a temperature control loop logic. For example I have 3 hiller all are duty and base on common return temperature, it will work
Nice information video thank you ❤
Dear sir I am facing problem frequency on my vfd is set on 30 Hz . If I want to increase frequency error over voltage shows on screen. Pls tell me about setting. Thanks . IFTIKHAR
Can you tell me what is the output voltage at 30hz
hello contact details! email
Amazing