Видео

It’s a fun project, good luck! Make sure to get a deep pour crystal clear epoxy so you can do it in one pour.

@ thank you so much man that tip will help heaps. Have you got an idea of what the cost of one would cost to make?

Hopefully you can find the keys for less than $80 and the epoxy will probably be $100-200. If you have all the tools you should be able to make the body for less then $300 maybe may less then that. Then it just depends on what neck you pair with it and electronics.

Thank you!!!!

😂 yeah, everyone asks if it’s a keytar

Thank you!

Yeah I would think you’d have to delete that then make the move in the video above

Hey bud, you an get all the electronics from Amazon or eBay. If your willing to wait you can get them from Ali express or dhgate. Do your research. If you use hoverboard motors make sure the motor controllers are built for hall sensor motors and the right wattage etc

@@TheSurfer446 i have a hover board battery so would i get a 36v esc?

Yes a 500 watt for brushless motors

I’ve gotten a few more, learned how to foot land, but need to get back at it! Life has gotten in the way a bit too much.

I got lazy and just left it zip tied lol

@@TheSurfer446 lol I know that feeling , if it works it works :)

You may be able to use a 48v controller with a 48v battery and it most likely will got faster, but then probably overheat and break. The motors are so cheap it’s worth a try tho. Make sure you use larger size wire for the feed. You could also upgrade the speed by keeping the same voltage and upping the watts

Thanks bud, sorry the video quality’s not great

@@TheSurfer446 people who complain about bad RUclips video quality make me think, "THIS ISN'T WHAT I DIDN'T PAY FOR!" RUclips creators get my respect for sharing the knowledge, period, end story, mad props.

Never flew up north yet but want to hit look out mountain to learn how to foot launch. I was taught just to throw the bridle behind you when you do a belly land

@@TheSurfer446 When you get more comfortable up there, you can just ball up the rope and stuff it between your chest and the top of the harness. You'll get faster/better at it with time. But don't let it distract you from getting control of the glider after tow release.

Thanks for the advice!

I used the same charger plug and charger as the hoverboard

I would definitely do it with 2 batteries from the start it gives it a little more punch and it lasts a really long time on one charge. Believe it or not the plastics are perfect just enough grip and just enough slide probably because of how much surface area is on the ground. But On certain surfaces it will actually grip enough to wheelie

@@TheSurfer446 absolute legend thanks. U got a new subscriber!

Did you build one as well??? I’d love to see it!

Probably wouldn’t work super great pumping it. It I think it would work with a mast and sail

@@TheSurfer446 thanks

Thanks!

What you say is true however an aerofoil does 2 things. An aerofoil increases the range of angles and speeds for which the wing will not stall. Aerofoils also decrease drag ratios for wings, especially parasitic drag. ...Just be sure that the back of the foil is fairly sharp tapering. Cheers

Awesome man, hopefully my video helped a bit

Update: All done!! Skar 6.5" sub, 2 ohm wired in series to get 4ohms. Kicker KS 6x9 2 way Components in the front (tweeters mounted in original location using a backstrap to hold them in, KS 6.5" Coaxials in the rear doors, Kenwood KMM-X704 dual USB deck, Kenwood X802-5 5 channel amp, 4ga power and ground to the amp, all new speaker wiring and RCA twisted pairs from the deck to the amp. Delete ML amp, Delete Center speaker, Delete Cargo door speakers, Delete CD Changer, cut harness tape and remove harness block from frame then moved OEM Pioneer HU moved to top inside of the glove box where the CD Changer was .. After some tuning of the new decks settings, the new system sounds great.. Note, you do lose voice navigation and OEM bluetooth with the removal of the ML amp, but its a terrible Nav anyway.. Bluetooth will run from the new deck for phone and streaming. If needed I will use Waze from my mobile device and bluetooth sound over the new audio system.. I also did lose steering wheel controls as I'm not sure how to tap into those with this specific setup. All is all disappointed that I even had to do this, but from what I read over and over , its a matter of time before the ML amp fails anyway

I’m not sure what you mean... I have an actual foil and this homemade one is definitely not as good but it does work.

@@TheSurfer446 The little kite that takes you out (and up on foil) in Surf... the new sport. wing surfing on foil board. Wng foiling. -Great job! -Cheers!!!

Your right! My camera skills suck!

@@TheSurfer446 The Camera point to where YOU point it. Alternatively you could just put the piece you want to show within the range of the lens...

A 6” pvc pipe coupler for each wheel. I threw some 3m spray glue around the tire and slipped it on making sure it was straight. It dries in a few mins then you can drive on it. Plumbing supply businesses will have the pvc coupler.

Jared Vermeulen thanks for the info. Quick question: when I check online the wheels are advertised as 6.5” in diameter, did you struggle to squeeze the wheels into the 6” couplers?

The wheels I used were the 6.5” type and they fit inside the couplers no problem but they were used so some of the rubber of the tires had been worn away. I would say if you have a new pair and they don’t fit you could run it over some rough sand paper to wear them down to the proper diameter. Also if they are too small you can very tightly wrap duck tape around them to bring them to the right diameter. It sounds ghetto but it works perfect.

Hello, sorry for the late reply... The tape player still has to be connected for the rest of the screen and features to work, that’s why I relocated into the glove compartment. Its probably possible to single out the wires and run it through the originals but I wanted to use newer better wires and didn’t want to have to do all the testing to figure out which ones were which. Hope that helps.

I got the art work of the storm trooper business man online then added the “Carpe Diem” and filters with an app called “perfect image” then just printed them on sticky back paper. Hope that helps!

@@TheSurfer446 Thanks, Jared!

Thanks! Hopefully it helps out some DIYers

Diego Magana bump

Idk about 2001s but technically you could do this mod to any vehicle. As for the head unit, if there is a single din spot then it should match