Building MHD my next boat.
Building MHD my next boat.
  • Видео 66
  • Просмотров 74 742
Ep 44. Choppy water
Sound turned down as we were talking about some crap. 15-20Kn wind from the port side. Always going to get some spray. Boat handles the chop well.
Просмотров: 211

Видео

Motor start
Просмотров 2002 месяца назад
Motor start
Ep 43. Water test pt.2
Просмотров 3122 месяца назад
Built a CNC Marine 6510cc Plate Alloy Boat. 2nd part of the test returning to the harbour. 225 Mercury Pro XS with a 16p prop may be a little tall couldnt get it to rev to 6k. Brand new motor still running in.
Ep 42. water test pt.1
Просмотров 4802 месяца назад
Building a CNC Marine 6510CC Plate Alloy boat. First time on the water. Went so well, new motor not really trimmed properly 39knots should do 40 easy. Corners like its on rails. Love it so good.
Ep 41. Painting the boat.
Просмотров 1772 месяца назад
Was a rush to get the console and back painted to get the motor fitted. That all went wrong and what should have taken a few hours, took 2 days. Well after it was home with fuel issues so not water tested yet, I've decided just to finish the painting. Its basically all painted now(rear dech hasnt been done because im not sure what im doing with seating) just waiting for stencils to paint on the...
Ep 40. finishing off the bumpers(Rub strips)
Просмотров 9453 месяца назад
Building a CNC Marine 6510CC Plate Alloy boat. Finishing off the rub strips and the gunwales ready for sanding.
Ep 39. Bumpers
Просмотров 4424 месяца назад
Building a CNC Marine Plate Alloy boat. So I had some help to fit the Bumpers. And it was hard work. Found out after its easier to start at the front rather than the back. Anyway leason learned about 2h a side was the final result.
Ep 38. Outside gunwhale edge + electric motor mount
Просмотров 1894 месяца назад
Building a CNC Marine 6510 Plate Alloy boat. Nearly done weld out the Gunwhales and weld the T Top down. then grab rails and a few of my own additions to go.
review of tools
Просмотров 3494 месяца назад
I was asked to do a review of tools used. Im not good in front of the camera or with public speaking so I've done the best I can.
Ep 37. Fuel tank hatch
Просмотров 4075 месяцев назад
Ep 37. Fuel tank hatch
Ep 36. MHD gets a trailer
Просмотров 3055 месяцев назад
Ep 36. MHD gets a trailer
Ep 35. Battery box
Просмотров 2465 месяцев назад
Ep 35. Battery box
Ep 34. Rear pockets
Просмотров 2335 месяцев назад
Ep 34. Rear pockets
Ep 33. Back end complete
Просмотров 6535 месяцев назад
Ep 33. Back end complete
Ep 32. Cast Deck Fitting
Просмотров 5406 месяцев назад
Ep 32. Cast Deck Fitting
Ep 31. Building the cast deck
Просмотров 4466 месяцев назад
Ep 31. Building the cast deck
Ep 30. Finishing the floor
Просмотров 3726 месяцев назад
Ep 30. Finishing the floor
Ep. 29 Making the hatches
Просмотров 7176 месяцев назад
Ep. 29 Making the hatches
Ep 28. Floatation
Просмотров 7976 месяцев назад
Ep 28. Floatation
Ep 27. Floor Stringers
Просмотров 4386 месяцев назад
Ep 27. Floor Stringers
Ep 26. Rigging tubes
Просмотров 4286 месяцев назад
Ep 26. Rigging tubes
Ep 25 building a fresh water under floor tray for a tank.
Просмотров 4886 месяцев назад
Ep 25 building a fresh water under floor tray for a tank.
Ep 24. Turning back over
Просмотров 4767 месяцев назад
Ep 24. Turning back over
Ep 23. Keel and keel cap.
Просмотров 1,1 тыс.7 месяцев назад
Ep 23. Keel and keel cap.
Ep 22. Outside Chines to sides
Просмотров 7257 месяцев назад
Ep 22. Outside Chines to sides
Ep 21. Under side back deck
Просмотров 7127 месяцев назад
Ep 21. Under side back deck
Ep 20. Underside Chines to Hull
Просмотров 1,7 тыс.7 месяцев назад
Ep 20. Underside Chines to Hull
Ep 19. Rolling over
Просмотров 8547 месяцев назад
Ep 19. Rolling over
Ep 18. inside chines
Просмотров 6577 месяцев назад
Ep 18. inside chines
Ep 17. Kill Tank
Просмотров 9847 месяцев назад
Ep 17. Kill Tank

Комментарии

  • @cncmarineboats
    @cncmarineboats 9 дней назад

    Great stuff Raymond!

  • @iainlyall6475
    @iainlyall6475 12 дней назад

    crap!

    • @MHD-Fishing
      @MHD-Fishing 12 дней назад

      Rubbish. Just guys talking about anything.

  • @atefabdallah7496
    @atefabdallah7496 22 дня назад

    Very nice boat my friend 🎉🎉🎉🎉❤❤❤❤

  • @dtreloar63
    @dtreloar63 Месяц назад

    you have used mig for most of the construction but you used tig to mount the trolling motor, why did you change methods? (Newbie who has no idea)

    • @MHD-Fishing
      @MHD-Fishing Месяц назад

      @@dtreloar63 smaller area neater looking just because I could

  • @brentritter7523
    @brentritter7523 Месяц назад

    how did you go about with the parts that need bending, did you do yourself or find a shop to? was it expensive to get them done

    • @MHD-Fishing
      @MHD-Fishing Месяц назад

      @@brentritter7523 I could have done alot myself but only a sharp radius. Because its a 12.5mm radius bend I went to an engineer's. All the bits bent was about $1600 which I think was way too much. Worked out about $30 a bend.

  • @adventurehungry
    @adventurehungry 2 месяца назад

    Would be great to hear raw sound of the boat and engine in the future. How does it handle compared to other boats you had

  • @BConnell-f6k
    @BConnell-f6k 2 месяца назад

    Good work. Glad you've finally got it out on the water

  • @martysprojects
    @martysprojects 2 месяца назад

    oh mate your on the water that's awesome, Ive run out of money on my build just saving up for the paint now. tight lines mate. cheers Marty's projects 👍

  • @marcianmoon6143
    @marcianmoon6143 2 месяца назад

    whats the total weight on the trailer? is it under 2ton ?

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      120L of fuel, start battery and 200ah lithium battery just under 2T. Ill be building a trailer soon, this is a mates who had a new one built for his boat. It will go over 2T loaded for sure.

    • @6knots6
      @6knots6 2 месяца назад

      Nice rig what electronics did you go for , cheers for the vid

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      @@6knots6 Lowrance Live 12x 2 with the AI transducer and a 1kw transducer.

    • @marcianmoon6143
      @marcianmoon6143 2 месяца назад

      @@MHD-Fishing i was told there are now complications and some new regulations with building diy trailers , requires engineering etc, were you planning to get CNC marine trailer kit ?

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      @@marcianmoon6143 more than likely a CNC one but if not i need to get certified plans yes. you cant just make your own anymore.

  • @brenttrotter88
    @brenttrotter88 2 месяца назад

    CNC Marine kit?

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      @@brenttrotter88 yeah

  • @madrestorations4452
    @madrestorations4452 2 месяца назад

    Where’s the growl of the V8

  • @adventurehungry
    @adventurehungry 2 месяца назад

    Looks great. Do a test in a chop

  • @cncmarineboats
    @cncmarineboats 2 месяца назад

    Getting real close now! Moving into the finishing touches.

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      painted on the rego number today on thge water Monday

    • @cncmarineboats
      @cncmarineboats 2 месяца назад

      @@MHD-Fishing Exciting times, looking forward to it being on the water. Send us through some snaps!

  • @6knots6
    @6knots6 2 месяца назад

    Bloody nice rig are you doing a vid on the wiring and final fitout what electronics have you opted for , I have pretty much the same rig 6.5m cc I’m hopefully getting a wrap on mine , well done

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      yeah just about there will do a final fitout vid. I havnt done any footage of the wiring directly but ill get some footage of both ends to show everyone.

    • @6knots6
      @6knots6 2 месяца назад

      @@MHD-Fishing awesome stuff cheers

  • @gmc9905
    @gmc9905 2 месяца назад

    What type of paint is that it seems to dry really fast.

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      Raptor by UPOL its a bed liner. I like it because its really tough painted a test piece back in January driven on it hit it with a hammer thrown the grinder on it still running it has marks but held up really well. Plus it stays cool in direct sunlight.

    • @gmc9905
      @gmc9905 2 месяца назад

      @@MHD-Fishing Thanks for the reply , we don't have to worry too much about paint staying cool here in Ireland.

  • @6knots6
    @6knots6 2 месяца назад

    Hey mate what you undercoating with how you finishing it off are you sanding it back ect cheers and thanks for the video

    • @MHD-Fishing
      @MHD-Fishing 2 месяца назад

      concept paints 110 metal etch primer. Putting Upol Raptor paint on for the top coat for a few reasons but im keen to see how it goes.

  • @GurienderKhakh
    @GurienderKhakh 2 месяца назад

    Ng bb y😮you c r tutoring ugii to I youth go ih

  • @GurienderKhakh
    @GurienderKhakh 2 месяца назад

    Hfhv

  • @GurienderKhakh
    @GurienderKhakh 2 месяца назад

    X

  • @TeganDrake
    @TeganDrake 2 месяца назад

    😅

  • @TeganDrake
    @TeganDrake 2 месяца назад

    😢😢😢😢😢😢😢😢 1 like for me

  • @gmc9905
    @gmc9905 3 месяца назад

    Watching from Ireland. Cracking boat keep up the good work. I've watched every episode so far , I'm a welder by trade wish I had the money to build something like this.

  • @BConnell-f6k
    @BConnell-f6k 3 месяца назад

    Nice

  • @beauyardy6196
    @beauyardy6196 3 месяца назад

    What's that?

    • @MHD-Fishing
      @MHD-Fishing 3 месяца назад

      Rod holders welded in

  • @levdon7679
    @levdon7679 3 месяца назад

    Со стороны левого борта зазор, люк рундука

  • @Cptnbond
    @Cptnbond 3 месяца назад

    Watching how you supported your MIG hand with various items was interesting. Cheers.

  • @iainhetherington4608
    @iainhetherington4608 4 месяца назад

    I’m curious are you a welder by trade or a serial DIY er and I’m not knocking you, either way I’m impressed by your work Cheers from way down south

    • @MHD-Fishing
      @MHD-Fishing 4 месяца назад

      @@iainhetherington4608 paramedic and DIY'r have built a few ally ramps roof racks fuel tanks over the last few years. First boat build

    • @iainhetherington4608
      @iainhetherington4608 4 месяца назад

      @@MHD-Fishing good on you for having a crack , I find aluminium welding to be the most satisfying, don’t know why Cheers

  • @iainhetherington4608
    @iainhetherington4608 4 месяца назад

    Can’t wait to see it in the drink 👍

  • @marcianmoon6143
    @marcianmoon6143 4 месяца назад

    thanks a lot for the info ! you got a lot of welders and other tools

  • @davidgreen1584
    @davidgreen1584 4 месяца назад

    Absolute quality welds👍 you should be really proud of what you have achieved👍 The welding looks very similar to the welds we achieve when ‘Burning’(Lead Welding)’ Lead on Roofs here in dear old Blighty

  • @marcianmoon6143
    @marcianmoon6143 4 месяца назад

    could you do a quick review of the tools ? how is the Unimig performing ? what AMPs/Volts combo you using for the thickness and how much duty cycle do you get out of it? would you buy a more powerful welder if you do it again ?

    • @MHD-Fishing
      @MHD-Fishing 4 месяца назад

      @@marcianmoon6143 sure that's something I can look at and a good idea. Ill try to have a look at that soon.

  • @nathangiles374
    @nathangiles374 5 месяцев назад

    How many hours in so far?

    • @MHD-Fishing
      @MHD-Fishing 5 месяцев назад

      havnt kept track but lets say 20h a week for 6 monthe 520h at a guess. theres been alot of lost time due to weather and work

  • @madrestorations4452
    @madrestorations4452 5 месяцев назад

    I am famous 🎉

  • @iainhetherington4608
    @iainhetherington4608 5 месяцев назад

    👍

  • @iainhetherington4608
    @iainhetherington4608 5 месяцев назад

    I have to ask where is the bilge ,or is it a self draining deck ? Looking good though Cheers from down south

    • @MHD-Fishing
      @MHD-Fishing 5 месяцев назад

      @@iainhetherington4608 self draining deck. Also there is a bilge under the rear transom deck so if water gets in it can drain to the rear. Ill do some pics soon to show what's where

  • @marcianmoon6143
    @marcianmoon6143 5 месяцев назад

    i thought battery box compartments would be pre-cut in the kit?

    • @MHD-Fishing
      @MHD-Fishing 5 месяцев назад

      @@marcianmoon6143 it gives you freedom to do what you like. I considered making the top a live bait tank very seriously.in the end just decided for storage

    • @marcianmoon6143
      @marcianmoon6143 5 месяцев назад

      @@MHD-Fishing can you create live bait tank integrated into bait board, there are few examples on other boats, bait cutting board would be the lid for the bait tank

  • @victorrevuk2992
    @victorrevuk2992 5 месяцев назад

    Super Work! Wishing 💯🐟

  • @6knots6
    @6knots6 5 месяцев назад

    Nice work does this boat have a bilge , self draining deck scuppers ???

  • @nathangiles374
    @nathangiles374 5 месяцев назад

    How many hours into the build?

    • @MHD-Fishing
      @MHD-Fishing 5 месяцев назад

      lets say 20h a week over about 26 weeks. So about 520h next one would be faster and with help its faster.

  • @iainhetherington4608
    @iainhetherington4608 5 месяцев назад

    Coming along nicely , have to commend you for perseverance, well done

  • @danielthornton3277
    @danielthornton3277 5 месяцев назад

    Aussie build? Looking good man

    • @MHD-Fishing
      @MHD-Fishing 5 месяцев назад

      @@danielthornton3277 yeah Aussie build in queensland

  • @cncmarineboats
    @cncmarineboats 6 месяцев назад

    Coming along great Raymond!

  • @davidgreen1584
    @davidgreen1584 6 месяцев назад

    You need better camera positions!! It’s all a bit distant 👍

    • @MHD-Fishing
      @MHD-Fishing 6 месяцев назад

      just trying to cover as much as i can but ill see what i can do. I now have a camera mount on the console so that should help. also action cameras are a bit like that ill make 1 less wide angle that may help.

    • @davidgreen1584
      @davidgreen1584 6 месяцев назад

      @@MHD-Fishing Did not expect a reply👍Thankyou 👍 I only thought I’d mention it so maybe you’d get more views/subscribers!! After all you’re actually doing it, building it! All I’m doing is watching your efforts😳 And the boat looks bloody fantastic so far. Keep going it all looks great👍especially here in good ol’ Blighty🤗

  • @hentran3848
    @hentran3848 6 месяцев назад

    Thật tuyệt vời

  • @iainhetherington4608
    @iainhetherington4608 6 месяцев назад

    Love your videos and progress mate , just one thing though the can of acetone just above you when you are welding probably not a good idea, hate to see all your good work ruined by oversight Cheers from down South

  • @초토하
    @초토하 6 месяцев назад

    What's the name of the float?

    • @MHD-Fishing
      @MHD-Fishing 6 месяцев назад

      @@초토하 it's closed cell foam. I got it a few months ago. I'll see if I can find what.its called

    • @초토하
      @초토하 6 месяцев назад

      Thank you.

  • @초토하
    @초토하 6 месяцев назад

    What is the name of the float you put on the bottom of the boat?

  • @tomosullivanmpbulls
    @tomosullivanmpbulls 6 месяцев назад

    Hi I’ve watched your vids looks good ! Do you think a 4.5 to 5m boat would be build able with only 1 person ? Or are two people needed fairly often ? I do have a gantry but am worried about needing two people

    • @MHD-Fishing
      @MHD-Fishing 6 месяцев назад

      2 people just makes it faster mostly it could be done on your own.

  • @marcianmoon6143
    @marcianmoon6143 6 месяцев назад

    what welding mask did you use ? did it have an air filter? is filtration any good ?

    • @MHD-Fishing
      @MHD-Fishing 6 месяцев назад

      I used the Unimig PAPR filter system when doing alot of welding especially in the boat. I also had an extraction fan to remove gas and smoke. When I do a quick weld and don't use the filter I have noticed it makes a huge difference.

    • @marcianmoon6143
      @marcianmoon6143 6 месяцев назад

      @@MHD-Fishing cool thanks , do you think its doable by a single person? have you built boats before?

    • @MHD-Fishing
      @MHD-Fishing 6 месяцев назад

      @@marcianmoon6143 probably more. When I get a helper a lot more gets done. No never built a boat before. I have done an aluminium boat building course.

    • @marcianmoon6143
      @marcianmoon6143 6 месяцев назад

      @@MHD-Fishing im planning to do the course too this year, i was thinking of starting with a smaller project first , maybe 4m dingy or CC. and then maybe 5.5m hard top