Видео

Thanks guy! Helped me out a lot this weekend.. worst part of the job was to tranny line clips

what did torque did you set your large spindle nut at thanks

If i go gold prospecting, can i run it without the filter and bag?

It would help further to tell the torque specs on all those bolts. Thank you for sharing.

Can i have your topkick?

I always used a c-clamp and one of the old brake pads to press the pistons back in but ALWAYS make sure your vehicle has the calipers that don't require a special tool and or procedure.

So i noticed the procedure for setting the bearing nut was not mentioned . Also I am working on a GMC c5500 with a 13,500 pound rear axle and those rotors have only 6 of those T-70 Torx head bolts holding the rotor to the hub . The hardest thing so far about my project was finding the torque procedure for those wheel bearing nuts . “ initial torque of 77 ft lbs while rotating the hub , Back off nut 90 degrees then retorque to 18 ft lbs . There are 3 known different axles used on this series of truck and as of this video at least 2 different hub and rotor combinations …..

They make a proper tool for that that’ll do both pistons at the same time . Them “Sandwich clamps” have no chance against hydraulic pressure .

🤘🏽😎🤘🏽

Awesome!!!

I figure that loosing the wheel nuts when on the ground is best, as the force is against the ground then driveline. If one has added brake fluid, do make sure you have enough volume to force the fluid back as it will over flow. I am going to have to remove some when I do mine.

Harnesses link?

You could also just use the old brake pad and a trigger clamp to compress those pistons if you don’t have a compress tool

Can u make another set of doors for my kids ? How much ? I like the reverse full opening door compared to all the others I find

Do u have part number for what toilet drain u used, need to do this mod just can't find the one u used

Hi where did you pick up the latches. Awesome 170 🤙🏼

Thanks that video gives me the confidence to do my own brake jobs from now on

Yoooo,, I feel like a kid again wearing my moms stethoscope smh lolol

How do u install the retainer

#RuggedRadio look

Your audio sounds pathetic

Do you video of putting the caliber back on? It’s not sliding on for me

Very nice !

The oil that came out of the transmission coolant when you disconect it does it need to add any extra ?

Tire and wheel set up and link please

Link for the fox float shocks?!

Do I need to bleed the brakes after replacing the pads?

sounds like you are standing under a fan / wind tunnel

Not even wet vac function, sham on Hilti for their outrageous prices.

Post a video of it in action 🤘

How fast does it go

Where did you get your airbag suspension kit from?

What came with it any battery or charger

1:14 what is that? Air for parking brake??? Mine doesn't have that thing.

well done

I own a C5500

Jesus Christ show yourself taking the bolts off

That thing is wicked haha

Thanks for the video Tony I was fighting the rear axle and didn't realize how to get those tapered collars out, you helped me a ton

So What Year is this Rzr 170 ? I have the 2020 with efi , do they all have this issue? Thanks in advance . So what other mods you working on? Sprockets , clutch ?

I'd liked to see little more about brake pad removal

Awesome!! I was looking up stuff for rzr170 and then I seen your face on the RUclips thumbnail lol. Sup bro, it’s little Brian. Finally paid off my kids Rzr, so now I’m looking to do some mods. I love this snorkel idea

Would this work for a 2015 escalade?

Awesome video...thank you for doing it! When you slide the axle shaft out, do you have to pay particular attention to alignment of the axle shaft or do you simply take it out and then slide it back in when finished?

Would have been much better had it shown the job in progress, not after it is done...it never goes as easy as just “loosen this bolt and take it apart”..would like to have seen the parking brake connection....

That’s hella cool bro! How fast is it?

Great job Tony. Thank you for taking the time and providing such a detailed video!

Did you have to replace any seals, bearings, or gaskets? I have to replace the rear rotors on mine. Thanks

Great video, this will help me a lot, i have to do the ssme thing real soon. Thank You!!!

Your video says, "how to replace brake pads and rotors". You did not demonstrate how to replace the rotor.