My control board has no blowout but I’m getting a F-02 code. The blue wires connecting to my display board are very finicky when I move it around but the current on the display from that chord alone are all closed and test passed. What do I do 😫
If the solder doesn’t work, u can try scraping away some of the green pcb to expose the copper trace. This will help additional solder make a connection.
Hello and what do you mean just solder? Did you replace and solder something? Confused please help. I checked all except board and all looks good yet dryer won’t start
OMG. THANK YOU SOOO MUCH. You saved me from being in the doghouse big time. I told my wife I could fix this problem (no start). I’ve had this dryer apart a hundred times to clean out the lint. I checked the ohms across the starter motor and didn’t get a reading so I thought my motor was bad. Ordered one and waited a couple days. Put the new motor in and.. {click}. I thought it was the motor until I saw your video. Sure enough it was the problem. 10 minutes later (to let my soldering gun warm up) and the dryer starts! Thanks again!!
I have LG dryer with TE1 error, I called a repair person and replaced thermistor with no luck still have the error any idea if it’s a bad control board.
Steps to Reset Press Power to turn the dryer off. Unplug the dryer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the Start/Pause button for 5 seconds. Then plug the dryer back in or turn the circuit breaker back on.
Thanks for showing this. I could not figure out what the problem was after replacing the pulley checking both the pulley switxh and the thermal fuse. The board had blown. A little solder and all good again. 😊
They have magnetic screwdrivers, there the ones with the black tips they work slightly better then this cause the magnet is on the tip instead of on the side
I’m actually a Utah native born and spent the first 30 years of my life here. Moved away for 30 years to the Midwest, not California. We move back to be close to aging parents and grandkids.
Please! I will switch with you today! You see snow, I see no loud and disrespectful Mexicans or ghetto black people. I don't hear horrible carnival music or some corn horn honking. No broken down cars in run down yards. And the best, you probably hear English there! No, you're in a cold ass heaven compared to LVegas, a.k.a. little l.a., a.k.a. little t.j., a.k.a. little san francisco (cause of all the fags). You are extremely blessed!!!
Move to Michigan one day it will be beautiful outside then the next day snowing and raining then after that it will be beautiful again. Michigan is bipolar lol.
My control board has no blowout but I’m getting a F-02 code. The blue wires connecting to my display board are very finicky when I move it around but the current on the display from that chord alone are all closed and test passed. What do I do 😫
@@beccabischoff4079 i'm sorry that's way above my pay grade 😢
If the solder doesn’t work, u can try scraping away some of the green pcb to expose the copper trace. This will help additional solder make a connection.
@@adamsorrenti10 thanks for the tip. I just had one yesterday that did not work after I soldered it. I will try that and let you know
@@adamsorrenti10 thank you so much. It worked. You just saved me $70
@@adamsorrenti10 it worked. Thank you so much you just saved me $70
Instead of rolling your right wrist if you're right handed, fan it backwards
Thank you bro, you're a life saver 🙏🏿
@@DoTheRightthing920 I just repaired another one of those today
@@markheartland2 next time I have this issue, I will go directly to the board
Great Video ...Just Repaired my Dryer By Doing exactly what you Mentioned
@@davidvasquez5386 awesome!!!
Hello and what do you mean just solder? Did you replace and solder something? Confused please help. I checked all except board and all looks good yet dryer won’t start
@@apostolicway2604 ruclips.net/user/shorts9M2p0nZA7kI?si=3Szl1-jI2F_8VwDw
Tshirt “how dare you, I identify as a Lint!”😂
My guy.... many many thanks for this information.... you have saved me alot more time and money than you know.🙏🙌
Awesome
Hello, my dryer has the same problem, what can I do to fix the problem, please help me.
Watch the videos. There are three parts. You need to get the computer board out and look at it
Ty this was my issue and it worked w a soldering gun and some soft core solder beed reconnected the blown circuit 👍🏼
That's awesome. Thanks for sharing
Tried to do the same with mine, looks like they are pouring apoxy or something over the entire board so I'm not able to get to it.
OMG. THANK YOU SOOO MUCH. You saved me from being in the doghouse big time. I told my wife I could fix this problem (no start). I’ve had this dryer apart a hundred times to clean out the lint. I checked the ohms across the starter motor and didn’t get a reading so I thought my motor was bad. Ordered one and waited a couple days. Put the new motor in and.. {click}. I thought it was the motor until I saw your video. Sure enough it was the problem. 10 minutes later (to let my soldering gun warm up) and the dryer starts! Thanks again!!
Thanks for sharing. Is my pleasure to hear reports like this
Warning. Do not test the dryer the way I tested it. Severe shock could result.
ruclips.net/user/shorts0Fh79FfK6oo?si=ILNaC4t45NTo_71B
I have LG dryer with TE1 error, I called a repair person and replaced thermistor with no luck still have the error any idea if it’s a bad control board.
Steps to Reset Press Power to turn the dryer off. Unplug the dryer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the Start/Pause button for 5 seconds. Then plug the dryer back in or turn the circuit breaker back on.
There had to be a reason the board had a blowout.
Yes, it could happen with a power surge, or possibly incorrect grounding. Might be just a one time thing.
There had to be a reason the board had a blowout.
True. Sometimes it could be some kind of power surge, but I'm not Electrician so I don't know for sure
Worked for us thanks.
Awesome
Where is part 2 ?
ruclips.net/user/shorts0Fh79FfK6oo?si=ILNaC4t45NTo_71B
Thanks for showing this. I could not figure out what the problem was after replacing the pulley checking both the pulley switxh and the thermal fuse. The board had blown. A little solder and all good again. 😊
That's awesome thanks for replying
Aliens are human fishing man lol 😂
sry, but u can see the line and it hooked to the line.
Yep
That's where my come rag went
The affects of MARIJUANA 🤣🤣🤣
A feather tied to a thin wire being pulled along
Lol.yep
Thank 😢. You You’re so. Kind
Tks😮
Please show us How you fix it, We know the problem
Sorry, I don't check replies. This is a three-point video that shows how to fix it.
Still waiting on those other 2 parts .... 😕
@@Rackus82 the other two parts are there
They have magnetic screwdrivers, there the ones with the black tips they work slightly better then this cause the magnet is on the tip instead of on the side
Just swipe a magnet across your screwdriver bout 10 times n you'll have magnetic screwdriver
You probably know they exist but maybe just buy a magnetic screwdriver. Cool trick if you don't have one tho.
Yeah, all the work I do and I don’t even have one
Or if it worked
Can u show me how to do the rest bc my dryer has a blow out
This is one part of a three-part video where I show you how to fix it
Messed up
You’re a free Bird
😍🥰😍🥰😍🥰😍
Awesome 👌 👏 👍 😍
Go back to California please weather is great
I’m actually a Utah native born and spent the first 30 years of my life here. Moved away for 30 years to the Midwest, not California. We move back to be close to aging parents and grandkids.
Every state other than Utah has already hit the 70s and 80s and we still have yet to pass 50°
Please! I will switch with you today! You see snow, I see no loud and disrespectful Mexicans or ghetto black people. I don't hear horrible carnival music or some corn horn honking. No broken down cars in run down yards. And the best, you probably hear English there! No, you're in a cold ass heaven compared to LVegas, a.k.a. little l.a., a.k.a. little t.j., a.k.a. little san francisco (cause of all the fags). You are extremely blessed!!!
Is beautiful I love winter and the snow ❄️ so beautiful 🤩
Living in Colorado and feeling your pain! 😂😂😂
That's funny
Move to Michigan one day it will be beautiful outside then the next day snowing and raining then after that it will be beautiful again. Michigan is bipolar lol.
i live like 7 minutes away from that resort i dare you to try and find me
Hey I’ve been their it’s a good fun beginner resort
Or an old guy like me who is not too concerned about being challenged on the slopes
Also realize the South facing house have a backyard full of snow. Ain't weather grand!
Yea I thought of that lol
What about the backyard...
Half of mine is still full of snow 😃
That's close, the best is an East facing home. On the west side. 😆 😆 😆
get yourself some dura-trac or other 3 peak snowflake rated tires. Makes a huge difference. Not quite snow tire performance but still really helps.
It was my neighbor