Видео

Thank you so much 😊

This is one of my favourites 😊

I think it is how it reacts to resin. All my creations have done it.

Sorry it is a baubuel, they hang on your Christmas tree. 😊

Hope all goes well for you. Happy this could help 😄

Thank you so much 😊, I will be returning to resin work in the future 😁 cant wait to start 😃

Thank you

I know I should, sometimes I got lost in the moment. I have made sure I have plenty now ☺️

Thank you so much 😊

Thank you so much. Works great with artificial flowers 🌹

Hello apologies for not replying sooner. I did not weigh the liquids. I kinda went with a 20 / 80 mix. 20 being water. But I kinda mixed a little and a time, until I was happy with the movement 😁 Hope you get it right for you.

I use half water half glycerin

Yes baby oil would work just as good. Easier to get hold of also ☺️

Thank you so much 😊

Thank you so much 😊

I laid it with the holographic film facing up. This would allow it to transfer, when I poured the resin. Then peeled it off, when set.

Thank you! Cheers!

Thank you so much. Although the resin does not attach very well to Jesmonite . Will have to glue.

Thank you, I used UV resin on a new project and it worked very well.

The fabric I got from Hobbycraft here in the UK. The mix was from Polysil UK. Thank you for asking, I am happy to help.

Thank you so much 😊

Exactly that, the film kinda just stuck to the mold and with the weight of the resin when pouring, it did not move. Thank you, and apologies in the reply. I have only just seen them all.

Thank you so much. I have found it quicker just to cut around the mold. Haha

Thank you, this set is definitely one of my favourite creations 😁

I think it is the 5mm bauble I used. It fits lovely in this mould.

It has been a while since I made this skull. I placed the cling film loosely on my first layer. Once cured 24 hours later, I removed the film and completed my final layer. Each layer took 24 hours to cure.

I used a can I purchased from a hardware store. Usually used for metal fixings or chains.

I used a photo paper. Think it was a HP brand. 😁

The skull was about 5 6 inches in depth. It is a mold I got from Amazon.

Thank you for this advice, will definitely take it on board for any future projects 😄

I think I just poured and added water a bit at a time until I got the right viscosity 😀

Thank you

Thank you so much

Thank you, 😊

Thank you so much 😊

Thank you, this is still one of my favourite creations 😃

Thank you so much 😊

So sorry for the delay, have been away for a while due to new job and career change. I am S Murphy Art on Instagram also.

I would also like the video please 🙏🏻

I still can’t find this snow globe part of the video tutorial. Instagram you mentioned that the visto is on “mh channel”. What and where is that? I feel like I’m chasing this video all over the internet.

Right?

​@@leannharris5854 I think I figured out how to seal it. Cut the top off tje ornament. Lime the edge with UV resin and put a clear, plastic piece over the top then use a UV light

Yes I you can, if you position it correctly.

Sorry about the delay in replying, I have been away from my channel. Started a new job x You would be able to add a druzy in the top.

I hope you managed to give this ago and it turned out amazing 🤩

I think it all depends on what you use. But normally cling film can withstand some heat. As I used to over food when heating in the microwave.

You don't need to use any cling film the ball can go right into the mold without it. Also the bauble can sit right into the cavity without any sticks or having to balance it. My friend makes them all she does is coat the bauble in some resin once bauble is filled pour resin half way up mold let it cure. Once cured she brushes the cured resin with mica then pours the rest of the resin to the top.

I got mine through Amazon x I hope you managed to give it ago and it turned out beautifully.

The inner mold stopper I used in this video, is a silicone inlay I made. There is a video of me making the inlays 😀

Apologies in the delay, I have been working so much and been away from my channel. The ball is 6mm. It is a Xmas bauble 😊

@@smurphyart-love2create268 ❤️ awesome thank you so much for helping me. There's no need to apologize your a busy lady . I hope you have a great day and weekend coming up. And get some rest

Tools I use sticky tape once it has set. I should be wearing gloves. But if I do get it on my hands, hot soapy water has helped and I do use hand cream.

Rubbing Alcohol first, then soap and water, finish with a little hand cream. This works best. ❤

6mm, it is a Xmas bauble. I purchased a pack of 12 from Amazon. Thank you 😊

Thank you, this film worked with my Jesmonite but not on concrete. Although, I am still yet to actually try the inlays you can buy 😁

The plastic one suspended better I feel. I think glass would be heavy. But, it may work the same. I have not tried it myself. If you do, please share your result ? I would be worried, if it was dropped 🫣