Видео

Мышиная жопа 😂

Before you put the new bearing on, leave in the deep freezer about a day for a better fit when you're putting it back together.

I could have sent pictures of my front wheel

Perfect video! Now where did you find the replacement chuck?? Can't find it on Amazon...

There are so many things I'd have to change before I'd use one of those splitters. This is one of the few that have a log platform behind the wedge to catch the split logs (nice option) That would have to be one of the first things I'd fabricate on mine. I'd also make my own stand which would be wider and more stable than that poorly constructed flimsy stand.

Mine blows 20a circuit breaker in panel when I hit start. Any ideas what could cause this? I read online capacity failure possibly? I am going to tear it down.

自分のcruz bikeにだいぶ昔に取り付けた普通のXTは、月1回のパーツクリーナーでの洗浄と、スーパーゾイルという潤滑剤吹きかけで15年経過しても、ガタさえ出ていません。交換したのはプーリーだけで、こちらはデュラエースの物に交換しました。気が向いた時の洗浄とメンテナンスをお奨めします。( ˶'ᵕ'˶)︎︎𓂃⟡.·それと､ディレイラー取り付けボルトは締める前に一旦逆回しして、捩じ込み開始点のコツンとした感触の有る位置まで回転させてからの、正方向への締め付けをすると、ネジを舐めたりしませんよ。

Since you paid extra for the weight savings, you need to upgrade your cassette, a lot more weight saving there compared to the one you have.

You must be an xc racer to pay the extra for the weight savings . The xt feels and shifts exactly the same to me, both are awesome.

The beauty of physics, mathematics and the human brain!

Very well explained and thank you. In my opinion that's not a good design. When you torque the cranc pin nuts, surely there must be some movement on the opposite end of the flywheels and therefore also on the center shafts which means the two shafts are not 100% aligned? I just dont like it i suppose.

To get a broken blade out all you need to do is hole the button that releases at and use the saw.

Play Through The Fire and Flames next.

Do not touch the measuring stones with your hands! Wear gloves!

Good job!

I got one I haven't used it yet hopefully it won't smoke interestingly the sale was yu buy one tool yu get one free it came with a other tool

Super nice look! Once I replace my Cannondale FSi this will be the successor

Cool vid and v obscure soundtrack selection 👌 love it all!

Your supposed to put a special oil in your grinder. Think it's called air tool oil, it's supposed to go into the hole for the quick disconnect. But that failed sealed bearing is an issue. But judging by the water in the lines you have not been draining your air tanks or running a dryer on your compressor

Wow! I need this for my Lefty Hub. What does it cost? Really like it!

Very very cool, what are you using for the fluid simulation?

The beat is so relaxing in my bass boosted crusher headphones from skullcandy no this comment isn’t a sponsor 😂great work brother charge for ur time

How are you gonna make such beautiful legs and then use that ratchet ass plywood for the top? I know it’s a work table but cmon man.

Cabrio platinum

Nice fix. I am glad you were able to save it from the dump!👏 What a drag to have to climb the roof just to change the dang batteries. It needs a small solar panel and maybe a 3.7 V lithium rechargeable cell, perhaps harvested from a solar light?

Can the hairdryer still work if you cut out the heating coils? Looking to modify so the heat function is completely disabled

Thanks bud!

😅 this is more exciting than the real thing

Fantastic. Thank you for the video

И чё?!

How many kidneys will I have to sell in order to buy that machine?

То, что человек построил, другой человек за всегда может сломать 😂

Good test. Name of music?

Just go for 35-40 NM, with 4 bolts you can't go wrong.

First thought is press brake punch, but with the 90 it probably isnt. Maybe some sort of stamping tool ?

One side says: W. F. Jennigs. The other one says: 1960 - so this is an Apollo-era tool

What does it say on the other side?

Since the failure is unconfirmed, will you keep the unit as a spare? I think it's actually cool that the 2 pumps are at least able to be disassembled and possibly repaired- a lot of the washer pumps are sealed shut. It also sounds like the notorious 6005/6006 bearings are still good, and the tub seal is still holding. Thanks for your video!

Krásná práce 👍

Top d+!!!!!!🇧🇷

POS i used this a total of 5 times then it stopped press trigger nada battery fully charged 😤

Our Frigidaire Microwave interior light comes on, but the screen is dead. Any ideas?

I have electric log splitter force The Pusher is broke can you tell me where can I get that part

Maybe the magnetic field from the stator coils was making the mesh rattle, if it wasn't rubbing on the rotor.

Very nice implementation of your project! Good job!👍 I used to work at a place that used something similar, a Georator, to convert shop power into 400 Hz 3 phase aircraft power for some of our test equipment. They take a beating, having a lot of run time, but are reliable. I think it would make a big difference if you would place those acoustic panels around the motor for noise suppression, as long as there is cooling air flow.

I have been nurturing my anilam for years as you and remember a comment you made about people, in essence, tossing out old machines. I suspect that you, like me, seem to resonate when an old anilam is getting pushed out the door. there seem to be more anilam machines closer to their eastern origin so I wanted to ask to let me know if you see an old machine appearing ready for a second life. what I imagine would be fun would to find is a bed mill with a tool changer that has AC motors. I further imagine installing my spare parts to make it have all the cool features. What have you seen that is not in the resellers overpriced unicorn stable?

This saw is a piece of crap. Mine started making ominous noises on the first big job. Thanks to your vid, I see that it's basically disposable.

What do you think, will they ever bring back the show to Yack? Did COVID kill off everyone with interest?

Sometimes I'm glad youtube doesn't have smell-o-vision, but maybe this time I'd enable it.

Now do it on a full one....