Видео

Love this video! Thank you for this!!!

U can get a jig saw for like $30 bucks at Harbor Freight. Good lord what a hack job. FIY, use weather stripping from Lowes/Home Depot instead of spray foam. It's cheap and comes in various sizes. Expensive sub and a cheap hack job install.

The wiring bit would of been helpful 😢

Pretty versed in this kind if stuff, I'm impressed at what you achieved with the tools you had.

Couple ugga duggas on the crank is a bit wild

This shit is crazy. Especially if you have a super mint non molested S13. So invasive 🤦 props to you man.

What was your measurements on that driveshaft???

Which is the best amaoil or LIQUI MOLY?

Rear won’t come off

Hey bro i changed from 1G to 1jzge-non vvti to a w58, could u tell me again the part abt the wiring in depth or send me to a link, cause im not sure which wires connect to the gearbox

Best car video on RUclips

Hey what was the spray you used to clean oil around the filter?

Good job sir. Im sure it sounds good. I think this is what's called an infinite baffle setup.

What a joke just to get to it. My aristo Took 2 minutes 😂

There is video on YT shows the marking slightly off one mark,how about yours?

3:00 I'll be fuckin slamming my timing cover outta there too! Damn thing lmao

Thanks for the video, I suddenly want to replace my fuel filter

does anyone know of a video taking the headlights off of a x90 chaser

this video helped me locate and fix a coolant leak in my heater outlet hose. thank you!

If I am doing the jzx100 clutch fan conversion, do I need a JZX100 tourer S fan shroud?

Nice job bro

Very good men

I'm thinking of getting a jzx100. What performance mods should I start with?

Still running this kit? Still like it?

Did you make the battle eye or did you buy it from somewhere?

Do you still have this setup, and if so, how is it holding up? Any problems with over heating, etc etc?

absolute gun

Nice job. How do you compare the amount of bass you get with this infinite baffle setup versus having one 12 inch sub in a sealed box?

are you using jzx90 radiator or 100?

So this doesn't require a box correct?

I had a question unless i didnt hear an explanation in the video, but why did you cut the transmission in half again? Would love to know before attempting this

Was wondering how much of this applies to a jzx100?

love the content man, i was just wondering if there's any benefit to doing this over an r154? judging by the cost breakdown and the price of an r154 these days it honestly looks like using the toyota route would be cheaper

What about the trunk struts

Best JZX youtube channel, really well made videos and very helpful. On my own jzx90 i have recently went COP yaris coilpacks but now my tacho isnt working. will this unit be able to provide a tacho signal in my jzx90 would you know? thank you

Anyone know what front and rear pads would fit on jzx100? can’t find a solution ☹️

How is the NVH?

I did this about twenty years ago in my seventy seven cutlass Except I put two 12 in subwoofers And two 6×9s Had to put in about an inch and a 1/2 or 2 inches of wood. So My spare tire would still fit in the factory location underneath the speakers Then I added another half inch piece of plywould paint it and cover it with speaker Grill material so you couldn't see the speakers at all Also had to cover the bottom of the 6×9s With boxes so the subs would not blow them out

Bilgilendirme için teşekkürler efendim RUclips kanalımdan 🎁 selamlar

Jeez if you had a simple Jigsaw you couldnt saved so much effort on the sub cutout hole, dont need a router for that

Thanks for the info man! Ordering some Avalon pads from auto zone as a temporary replacement until I can get Some ProjectMu ones 🥳💤🤟🏾

I used a Jig saw and Circular saw to build all my sub enclosures. Then a Dremel for fine sanding. Nice work young Man!!

Hey Kenny will this work on a soarer 1j non vvti too?

Wow, so many more steps than a modern car. They didn't think about making it easy to change back then :)

This is a great tutorial! Thank you

I love how you made use of the tools you already had!!!!

Also trying to put heat back into my s13. And wondering on a parts list needed? So far just got the air ducts, blower, heater housing? And just read above that I need the ac evaporator too? Thanks in advance dude! 🤙

do you still have your automatic shifter assembly (0:59)? Mine is kinda ratty so I was hoping to swap it but I can't for the life of me find one anywhere nor can I find the part number on amayama. Anyway if you still have it I will buy yours!

Will the process and parts needed be the same on an NA (Non-VVTi) 1JZ?

What rear rotors are compatible with Grande 1997?