Видео

My Wacker, I highly recommend Black Jack, very impressed all around good service, communication, and happy with price. Call him up for your Wacker repair.

One of the best teardowns I've seen. You made everything very clear. Thank you.

I didn't watch the whole video but that carb looks like an aftermarket Chinese part. They eye catching part is the choke lever being red rather than orange.

Maybe take time to show reassembly steps. If you’re going to make a video, information doesn’t need to be withheld.

Great job

Hell yeah brother! I appreciate the time you spent documenting the process. I am watching the videos tonight so I am prepped for the morning lol. Cheers from Oregon!

I hate when goobers don’t show you how they remove anything . Complete; more like incomplete! I didn’t even finish the video-

Jesus Murphy that’s stupid dude what the hell does that have to do with anything pay attention to the length of the line stfu 😂wow imagine they just put the same amount of line on 🎉

Very clear explaination, thanks for sharing.

You have to show how you did it and, you show only what you did. It´s not great.

Great video Hello from Algonquin Park Just rebuilt one of these that was being discarded It runs well But I may have the flywheel / coil issue you were mentioning Also the lower shaft is slightly twisted left relative to the upper shaft & the motor housing Not sure why

🫡🫡🫡💐💐💐

Today is Aug 9, 2024 -Thank you very much for sharing your knowledge. This is a very helpful and well explained video. I have a 24 yr featherlite weed eater and i keep it running by learning from RUclips videos like this. I also have a brand new featherlite weed eater still in a box to use one day my old one doesn't work.. God Bless you take care..

Nice video are you from vancouver? i thought i heard the skytrain in the background?

Man, thanks for these uploads. I have an FS38 or whatever it is. If i ever upgrade then this will be super helpful. Also, thanks for mentioning the screws being different, they look so similar but they have a different thread pitch. Thanks again.

Weed Eater Featherlite W25SBK

very interesting 👏👍

Great video! super easy explanation of how things work and go back together. Wish you were in Victoria!!

You should have more subscribers and likes. I learned a bit.

They told me at canadian tire this would charge my car battery in 24 hours slow charge been 10 hora so far went from 25 to just under 50 percent im wondering if im jist wasting my time

Can you tell me how long the charge was?

Hi

You need to file the hole in the mainjet a little bigger with a welding tip cleaner/file. It's running lean.

I knew I was going to like you when I saw the rum lol

I used kitty litter but this would smell much nicer

I can't start my eton beamer 11 scooter it was working fine but kick start but no fuel coming from petcock

How does the engine on this compare to a Honda engine ?

I see a spring already you have missing

Is there a chance you still have this generator if so I dearly need to look how your panel inside is wired up mine is a rats nest and I can't figure it out

Hey! I am rebuilding my bike, it’s the same as yours. I need help with re assembling my front tho, how the front and the headlight goes together and connects. Thanks!

Thank you so much for this

They are great little Motors, i have one in very good condition. I use it a a emergency Drive. Saved my ass 2 times from rowing back a few hours. Just love them. With 50% Aspen and 50% Gasoline 1:50 tcw Oil they are always ready for take off with very little maientance.

wonderful. Many thanks from Canada. Thien Tran. Do you have a video on carb adjustment?

I have few questions we have the same scooter. I got my scooter used, too. And it has some problems bog in down crazy or just not starting but 1 minute.. 1.) Where did you buy your carburetor ? I noticed now the owner switched the car. 2). Do you keep the cap on the spark plug or take it off ? 3.) What 2 cycle oil do you use ? And much to you put in moped ? Thank you

Something I ran in to the other week guy brings in a weeder with no start complain ...had used gas with no oil....had to order new carb cut the power of pure gas ramed the restriction needle closed and was not fixable

I am looking to buy one too .. what do u think .. ? Did u get it from home hardware ..?

My dignity was stolen from me when an entire police division assaulted me. They kept the picture though!

Hes absolutely. Correct. Looks like he has small engine repaire😊

I do this to my pens at work.

Sit with a scribe often at your box

lol

Best neighbour ever!

your the best broo

How big was the box?

Do you recommend the vavor 24 inch cleaner?

this product sucks it doesnt work i just used my booster and will start the car every once in a while o my

If you own a TD 33 that is not running correctly, and has the following symptoms: Poor starting / Uneven tickover / Bogging Down / No power when accelerator is depressed. Please focus upon the TK 1 Carburettor. At 14:40, you will see a Brass Primer Valve. Although this video does not show a close-up of this brass primer, you can see that it contains two (2) grooves towards the tip of the primer valve. This brass primer should contain two rubber 'O' rings. The purpose of these rubber 'O' rings is to seal, and to prevent any air from passing around the bore of this primer valve. The TK 1 is in my opinion, a poorly-designed Carburettor, because this brass primer is the #1 cause of poor running. To fix this, you must block-off the hole, and throw away this brass primer valve. I used an aluminium rivet which was a sliding fit down this bore. I first cleaned the bore with acetone (and this rivet too). Add a little super glue, then insert. Please also be careful not to add any superglue to the end of the plug that you insert. If you do this, you will block the Carburettor Main Jet!! I can see that over 800 persons have examined this video, and many would have starting / running problems with their TD 33. I modified my TD 33 in this way, and the machine ran like it was brand-new again! If you do not have an inline Primer in the fuel line - buy one and use instead of the brass primer. I hope this helps, because the Kawasaki is a great model, but the TK1 Carburettor lets it down for this reason.

The only way I make popcorn

Nice, and hope everyone appreciated.

Great job ! 👏