Видео

In this video I build & install a ball differential into my Tamiya Buggy Champ ready for the Knox Vintage Bash 3.0 in a few weeks. I take it for a test drive with a 2S LIPO shorty pack. I also bring the Hornet out again and test a 2S stick pack.

In this video I take my Tamiya Rough Rider, Hornet & Super Hotshot out for test runs and mess about with batteries, before I attend the Knox Vintage Bash 3.0 down in Melbourne with Jason @Bormac073 and Keith @rcicons4915. Thanks to Sacha & Scott @thehobbiesfactory808 located at Ourimbah, on the Central Coast for the advice on batteries.

In this video, I continue building the chassis of this awesome Tamiya Grand Hauler Matte Black Special Edition truck. I install the rear mud flaps and complete the body installation including the lights and wiring. Then take it for a for a test drive and demonstrate the MFC features.

In this video I paint another Sand Scorcher body. This time it's not for me, it's a gift for my mate Keith ​⁠@rcicons4915 in the USA. I based the colour scheme on his favourite, the Top-Force Evo. Check out his channel below in the link to him receiving this: ruclips.net/video/UPMsnWD_2yI/видео.htmlsi=LMdV9b2gZ_SO64wL

In this video, I continue building the chassis of this awesome Tamiya Grand Hauler Matte Black Special Edition truck. I install the coupler or 5th wheel, motorized support legs servo, multi-function control unit and wiring.

In this video, I continue building the chassis of this awesome Tamiya Grand Hauler Matte Black Special Edition truck. I install the main switch panel, side steps, fuel tanks, rear bumper including lights and wiring.

Arrived today! Unboxing the brand new Team Associated RC10T 60th Anniversary kit.

In this video, I continue building the chassis of this awesome Tamiya Grand Hauler Matte Black Special Edition truck. I build the 3 speed gearbox and install it along with a 33T hop-up torque-tuned motor, wheels & tyres.

In this video I start building the chassis of this awesome Tamiya Grand Hauler Matte Black Special Edition truck. I'll be installing a full set of Plaig bearings, hop-up Tamiya oil filled dampers and the multi function control unit for lights sounds and vibrations. Then I'll move on to the Shell fuel tanker with motorised legs and full light kit. It's going to be awesome!

In this video I paint the body, apply the decals & finish the build. The colour choice is my tribute to the vintage Rough Rider alternative colour scheme.

Awesome display at the Central Coast Airshow at Warnervale Airport. Featuring Paul Bennet Airshows, RAAF Roulettes, C130 Hercules, Piper Cub, P-51 Mustang, Grumman Avenger, Sea Fury, Radio Controlled F-16 Falcon and the F-35A Lightning 11.

In this video I show how to make a cheap set of LED lights from eBay fit the Tamiya BBX.

In this video I build the Tamiya BB-01 BBX Buggy chassis. It gets a Tamiya 15.5T brushless motor, TBLE-04SR Electronic Speed Controller and some nice Hop-Ups.

In this video I do a bit of maintenance on my Tamiya Ford Escort Rally MK 2. I upgrade the shocks to mini CVA, replace the lower suspension arms, upgrade the receiver, set up the ESC and take it for a spin.

Tamiya Ford F150 Ranger XLT MK2 Body Painting Metallic Vintage Colour Sheme

Tamiya Ford F150 Ranger XLT MK2 SRB Restoration

Tamiya Battery Connector Plug - How to Remove Cables

Tamiya Sand Scorcher Alternative Vintage Red & Yellow Colour Scheme

Tamiya Ford F150 Ranger XLT SRB Build Part 7 - Charge & Run!

Tamiya Ford F150 Ranger XLT SRB Build Part 6 - 360 Walkround

Tamiya Ford F150 Ranger XLT SRB Build Part 5 - Paint & Decals

Tamiya Ford F150 Ranger XLT SRB Build Part 4 - Chassis Build

Tamiya Ford F150 Ranger XLT SRB Build Part 3 - Strip Down Rear Suspension & Gearbox

Tamiya Ford F150 Ranger XLT SRB Build Part 2 - Strip Down Front End & Shock Absorbers

Tamiya Ford F150 Ranger XLT SRB Build Part 1 - Wheels & Tyres

Tamiya Ford F150 Ranger XLT SRB Unboxing