Видео

Thank you for the video!

Very helpful!

Just found your channel..If the starboard engine has a tendency to make the boat move ahead, is it more of a detent alignment issue or is it time to clean and service the control valve..Im pretty sure I have the lever detent ball on the trans and the detent ball on the shifter at the helm located correctly, but maybe I have to recheck them and adjust..Thanks

Thanks for this informative video. I have also have a 5.7 liter Black Scorpion engine. It is idling very rough, but the engine seems to run fine with higher rpms. Any idea what the problem might be? Thanks

FYI - you say PVC 1" adapter but at 52 in the video show a slip x slip coupling

Where did you get the purple gun?

You have a good understanding of these engines. What are your thoughts on a stalling issue I have. I have a 2006 Supreme with this engine I replaced all filters and the IAC valve. It has a new cap and rotor. After running the boat out on the lake when I return to the 5 MPH area while idling into the dock it will stall out and some times stall but not completely shut off. It starts right back up. Any ideas of where to start checking? It runs great otherwise but irritating when it randomly does it in the 5 mph areas. Everyone seemed to say IAC valve but a brand new Mercury valve was installed.

This is genius. Thank you. I am also going to experiment using an airlift connected to a compressor with no water pump.

bonjour le mien fait du bruit en marche arriere...

What air pressure are you using with the gun and how is it working with the liquid container sealed ?

I don't know how to share Amazon links in comments. However, I ordered a blower fan with an adjustable power supply for $19. It looks like it will plug into the pump instead of using the car plug. I also ordered the pump kit from this video. Both units are supposed to arrive tomorrow May 13th.2024. The blower fan is for an upcoming waste oil furnace build. I will report back as to whether or not the power supplies are interchangeable. It's a 6000 rpm blower fan if anyone is interested in looking it up.

Nice, concise and straight foreword. I appreciate your efforts. Will build one like it tomorrow, been working on a foam generator for a couple of days now but this looks a lot easier.

THANK YOU SIR -- I AM YOUR NEW FAN AND SUB --- BEST WISHES

What can you eat it with like what does it take good with?

I can only say, thanks a million!!!!! great video!!!

Great build. Will definitely follow. A question. Why a 12v pump and not a simple 110v fountain pump?

Just wondering, what is the benefit of this terminating into a thinner pipe? Couldn't the gun barrel simply end at the end of the 1" pipe? The wire will stop the stainless steel wool coming out so why is the thinner pipe necessary on the end? Thanks

Do you know if this is compatible with the 2007 black Scorpion 5.7? Thanks!

Hello. What specifications that compresor has? I am going to buy one, but I ignore those machines at all

Fantastic, thanks for sharing!

Excellent and fantastic video. God bless you. This lightweight and simple professional DIY Air-crete cannon gun will save me a lot of money. Also, I will be using it with a low-cost Car-wash liquid soap solution with 1:100 gallon dilution for my CLC block making pilot project in Africa. Thank you a million and have a great new year celebration. VG

Excellent video obeyed the 3-S rule Short, Sweet & Succinct

due to inflation this will be around $40. Steel wool items linked will run $19 and the sprayer is $17, to give you an idea of 2023 prices. Still I like the idea and will try it.

Awesome

What's the spacing measurement between the 2 pipes to hold the skis?

Well done

Very good job on this

FUSE!!!!

Looks great but that is nowhere near enough foam if making aircrete. You wanba fill a barrel quickly..

Excellent design.

Sorry if I missed it in the video - did you cut the existing power line from the pump and replace it with your own? The one you linked on amazon has the car charger connection. Could I substitute with a different power supply that I can plug in to that adapter? Thanks!

Good idea, I prove it, thanks

Best foam generator I've seen!

You never made an impeller replacement video for this engine? I have same engine/boat. Appreciate what you have posted👍

Well done

I tried that, but had a tube feed for the top. It worked okay. I also found that just a small amount of glycerine in the water makes the bubbles stronger. They last longer.

I appreciate so much that you shared this with everyone. Some try to gain on what they come up with. I cN understand that - to a point. Awesome Aircrete gun ! Now I can replace a 5 yr old design that didn't work so well. All the best, Wulfy

Awesome! Thank you.

7th generation soap has glycerin 1oz soap to 16 oz water

👍👍👍

Look at the 2nd video, there is a link in the description.

Theoretically this works but the amount of foam output is pitiful

Love this video. Have you or anyone you are aware of. made this yet? Would be very interested in the real life test. Have you made the plans available?

Did you try adding glycerin to the mix and comparing the foam life expectancy?

Excellent quality foam but tiny quantity, extremely inefficient.

I have this engine but do not have that monitor gauge near the engine. Is there a simple monitor to plug in to keep track of the engine hours?

can one use a Submersible water Pump instead? If yes, what type or model would be best? Thanks.

Hello from France, I'm going to try this, because I no longer have a forward or reverse gear.

I cut differently. Taking hairy part off first and take the seeds out. I’m leaving the skin on. It’s so better then without the skin.

Did you use marine grease?