Видео

Boiler heats water but no central heating. Radiator symbol is flashing. Any ideas of the fault? Pressure is fine and no F code on display. Thanks

Genius

Ive just done that, still not working

Mine doesn't heat up and i have presher and credit and its showing the flane on the boliar and on the fram ?

Everything from the boiler outlet onwards must be completely airtight. the siphon must also contain water. Otherwise your boiler will get false air. Only the end of the chimney must be open. If this is not the case, water will collect in the ignition.

How about isolating the flow and return first. As soon as you removed the magnet, you allowed the magnetite to flow through the system.

Can you setup the flow temperature under 30C ? It's possible that ? Or 30C it's the minimal flow temperature ?

Thx

Atag poor heat exchangers prone to pin hole take about 6 months to fire up if youve had to switch it off

Is that a rainwater collector? It looks like some sort of gutter down pipe home contraption 😂

That looks like my solution. 👌

So you obviously made it safe as that must be id.

How did you fix it ?

And how to fix ?

Hi, can you tell me what the annoying N27 error means

Pretty sure the safety discharge should be going in to a hot tun

That pipework is shamefull!

Thanks for the video. Very helpful

Absolute legend 🎉

Install debris filters and do yearly maintenance. problem solved

Can you use just your radiators always on and not turn the hot water on? Will it mess the boiler up?

This price for a fan is just stupid

What's that mallet attachment?

Could you advise me, is there any way of stopping the attached timer from ticking? It's so annoying 😵

I have f84 error aswell and the boiler gets f84 error when i turn on heating sometimes and i hav eto reset it, sometimes a few times and then it starts working again. do you know why?

Hallo I don't understand good English. Wat is this settings? Low. Midium. High. ... before down radiator is not so warm. And when i put it in high,now is hot.thx u

Who did that? Bob the builder?😂

SPEAK UP AND MAKE YOURSELF CLEAR

Just added this product to my cold radiator with a stripped bleed valve. Rad is toasty warm..no leaks. Do believe the haters (plumbers who want your money)

It looks an eyesore and what about the shit which is now floating around in your system from drilling through? The rubber washer will degrade with the heat and you'll be left with a leaking radiator before long. Just change the bleeding nut, its just as simple if not more simple.

Hasn’t worked!

I have this model of boiler but I can't close the heater can you help me open and close the heater even at night it works thank you

Why don't you close the valve above the filter? Surely some sediment can get pushed up through it if it's left open?

Do you know how to use the portable Digital timer ?

When do you bleed the boiler?

My hitting is not working what should I do please?

My heater is not warm, please help me, boiler everything is fine, made bar to 2.0, bleed the air already, set the temperature but heater is still not warm, please help!!!

Any advise please?

Hasn’t worked

Legend

You just helped me out a lot..thanks

You just helped me so much I’m in tears of joy!!!!! Thank you so much

Zdarzyło się że jakieś połączenie pociekło w uponor plastikowych ? Pozdrawiam

Hi I have a rapid 25 gas boiler. Before to go away for 1 week I just turned the gas boiler just pulling out the insulation fuse that is beside the gas boiler. Now that I put the fuse again give power there is no power, just seen for half second the lights On and Off and no power anymore. Do you think the logic card inside is burned or could is any inside fuse gone? Tested the power fuse beside the gas boiler still good. Any help please 🙏 Thank you

Ez ide kevés lesz, tudom nekem is van ilyen és erős milwaukee is.

Wow that's video was almost useless ,no discussion ,couldn't be bothered to show the fitting well done 👏 (NOT )

O-ring is squeezed by using U-profile not TH-profile ! It's important in new fittings with leak-check feature if it's unpressed yet !!!!!!!

Ta mate. Sorted 👍

My heating is ok (air source heat pump) but I'm not getting hot water. The water is set to 55°

how do you bleed pump and speed please on this