Видео

Thank you, was very helpful

Hi Joesph thanks for video I am having a problem separating the sensor switch tried pulling it off so I can get slack any suggestions

Still helping people 6 years on. Thanks man

I’ve had to clean the blower fan on my families Electrolux several times now 😐 great refresher video to speed the process up before diving in. Thanks!

Awesome video, thanks. Went from crazy banging sounds to once again quiet. I didn't have to replace blower fan, but it certainly needed a thorough cleaning. 40mins later I'm in the good books!!

Thank you for this! You saved me a couple hundred dollars in labor. Turned out my blower motor was completely full of lint. After clearing it my dryer sounds like new!

This video saved me a ton of time! Would not have known about the socket size or the "righty loosey" to get the fan wheel off. Also, same as you I had to remove the whole motor assembly and clamp the pulley in a vice to get the original fan off. I little Wd-40 really helped. Something else to note - the vibration when it was full of lint must have broken one of the spring metal clamps that holds the motor in it's cradle, had to order one but at lerast I noticed it while I had the dryer apart. Thanks!

Great video! Just what I was looking for. I'm tired of taking my Ena 8 in for service twice a year because Jura won't make their brew groups easily accessible like other manufacturers. Thanks again.

This video really helped me. The dryer was making a loud noise almost like a vibration. I unhooked the drive belt from the drum and the noise was still there. By following the video, I was able to clean a LOT of lint from inside the blower wheel and it is as quiet as new. Thank you !!

What size socket are you using

Thank you so much for this video!

Hi. I tried to take out the black side panel as you said to slide it (2:18). It doesn't move even if I tried very hard. Do you have any clue as to why? Thanks!

Thank you so much for posting this!

Thanks👍🏻👍🏻

Great instruction video. Additional maintenance tip: after a while the white plastic cog needs lubrication. I use salad oil for this. I can clearly hear the difference; the unit has less effort squeezing out the coffee grounds. This will also help prevent against Error 8.

Finally someone who knows the right procedure. Beware of other videos out there!

Can someone please help as tray is stuck as won’t come out. I think ive put it the wrong way. The small flap underneath is restricting the tray to come out.

Thanks so much for posting this, got the security key, and followed everything exactly. Was expecting to be horrified when the panel came off, but surprisingly a few clumps of mould. Bought the machine 9 years ago, and it has never been cleaned!

Thx for the video, I really want to buy a Jura ena 8 but due to the complex removal of the brew group I think il stick to machine types with easy removal of brew group like the Siemens eq 6 plus I own know. It's a shame there is so difficult to get to the brew group since the Jura makes a excellent espresso. But again thx for excellent video. Quick question what coffee machine do you use know.

My negligence has resulted in one of the little screws inside to become corroded (the 2nd one inside at the bottom on the video). I could not remove it so I unplugged the machine and transferred it to the sink and put it on an oven rack to drain and ran water gently over the interior parts. It's 90%.

You are the man. Thank you so much for helping. Good idea to just cut a groove into the super stupid JURA security screws. I used a rotary tool and a cutting bit to make the groove and then a simple screwdriver - just mentioning the possibility was great as I could get into the machine now and not have to wait. I cleaned out my machine and had to get into the grinder to clear it out and voila, it works. Thank you good sir!

Thank you so much for posting this! I took mine apart today, first time in seven years, and gave it a thorough cleaning. Previously I had just sprayed up inside where the removable trays come out and used a small brush and my finger to clean as much as I could there, which did help. I also had used a wooden skewer down the powder shoot, which had been plugged and prevented the grinder from operating properly. With your helpful post, maybe I’ll be able to get more years out of this machine yet! Its Jura replacement is already sitting upstairs waiting.

Great video. Mine has not been opened for 5 years. I can only imagine what I will find inside.

Thank you!

Great! You shared the secrets! After that peace of cake. Great brand, great machine but cleaning this part should be left to the consumer.

Hey Joe - Jura wanted $250 to deep clean my machine. I took your wise advice and bought the tool on Amazon and did it myself. THANK YOU SO MUCH! When you pay this much for a machine - you think they'd give you a break on repair and cleaning - but NO WAY! Because of your generosity - I am sitting down to a delicious cup of Joe with a scone! Thanks so much!

Thank you for your generosity in helping Jura owners deep clean their machines. You are saving us being ripped off by Jura repair shops and we all appreciate you very much!

Проблема может быть в двух местах (при наличии гудящего звука): 1 - клапан слива воды после приготовления напитка забился 2 - моторчик клапана слива воды из заварочного блока заклинило 1. устраняется путем промывки и продувки (снимаем боковую крышку, откручиваем саморез и болты заварочного блока, снимаем заварочный блок, убираем боковые накладки заварочного блока, снимаем клапан движением вниз) 2. снимаем боковую крышку правой стороны, отключаем проводку с правой стороны от платы управления, отодвигаем плату с коробом влево, видим моторчик приводящий в движение шток клапана, откручиваем два самореза и отключив провода снимаем. Отгибаем 4 зажима и снимаем пластиковый привод вместе со штоком, смазываем шток и червячный механизм, прокручиваем руками, чтобы распределилась смазка. Собираем в обратной последовательности. Вкусных напитков!

Thanks great Video, I have always wondered how to get the side panels off, just cleaned mine after 5years, has anyone put some food grade synthetic grease....just a bit on the gears any thoughts on my idea?

Very helpful video. Thank you.

we have to clean our machine at least every 2-3 months, since maggots appear in the coffee grounds container.... is there a way to clean it properly without having to take it apart?

have you found a way to remove and clean the 'cone' / funnel where the ground coffee falls in?

Thank you for sharing. Found the tool by searching Amazon "Jura Service Repair Tool Key"

Have you tried removing the grinder at the top?

Thanks for the video. I think this is exactly what I need to do. Grinder labors and throws Fill Beans error.

I bought the little key from Amazon after a frustrating attempt to remove the special Jura proprietary screws and did the job. Thanks, it needed cleaning but was not as bad as I thought it would be.

In the video you say that you put a slot in the screw head with "your tool". That is great however what tool and how did you get the screw out the 1st time. I have a small hex driver but it must be imperial measure because it is slipping.

How often do you use this machine? I have had mine for 6 years and I make on average 8 expressos per day. I am only now hearing a slowing down and labouring motor and it concerns me. This is the most comprehensive video that I have seen however it does not address a few issues. Where is the "labouring noise" coming from. The type and size of screw driver or wrench or used. I know that you say that you cut a groove for your screw driver but I live in Europe (France) and have a set of star shaped allen type wrenches. I see now mould in your machine and it looks quite clean so I wonder why you are going to so much trouble every few months. I think that if you were to redo this video paying more attention to the very small details, perhaps with help it would be exceptional. This is an important video to people like me as I do not speak French and to send the machine to a repair shop is a major issue. Ordering a box, completing a form in French, sending the box, being without the machine for 2 or 3 weeks and then being home when it returns by courier.