![michigan mud mechanic](/img/default-banner.jpg)
- Видео 140
- Просмотров 338 712
michigan mud mechanic
Добавлен 28 май 2021
I am not a certified mechanic. I just have lots of hobbies and like to work with my hands. This channel's mainly me challenging myself to see if I can pull it off.
Видео
Mazda 5 engine removal
Просмотров 3552 месяца назад
Same thing different video. #mazda5 #mazda #engineremoval
Equinox back on the road | 2.4 ecotec
Просмотров 585 месяцев назад
Equinox back on the road | 2.4 ecotec
Durango | Engine swap part one engine removal
Просмотров 447Год назад
Durango | Engine swap part one engine removal
Floor leveling in some minor construction
Просмотров 21Год назад
Floor leveling in some minor construction
First Test drive after engine replacement | 2009 Cadillac CTS all-wheel drive with a 3.6 liter
Просмотров 234Год назад
First Test drive after engine replacement | 2009 Cadillac CTS all-wheel drive with a 3.6 liter
Installing engine in my Cadillac | 3.6 L GM
Просмотров 329Год назад
Installing engine in my Cadillac | 3.6 L GM
replacing my Cadillac engine | 3.6 L V6
Просмотров 150Год назад
replacing my Cadillac engine | 3.6 L V6
Replacing AC compressor | 2002 Blazer ZR2
Просмотров 798Год назад
Replacing AC compressor | 2002 Blazer ZR2
Caliper sticking | collapsed brake hose Chevy Malibu
Просмотров 2,8 тыс.Год назад
Caliper sticking | collapsed brake hose Chevy Malibu
Chevy Blazer ZR2 | fuel pump repair
Просмотров 2,8 тыс.2 года назад
Chevy Blazer ZR2 | fuel pump repair
Timing chain replacement | 3.6 liter V6 high featured GM
Просмотров 3392 года назад
Timing chain replacement | 3.6 liter V6 high featured GM
Great job, I would have cussed out... seriously 🤬
The cussing was edited out. No tools were harmed in the making of this video. Thanks for watching.
This so for you to do for her
So... how do you get the exhaust manifold and alternators off?
Great Job Bro...
Clicking noise is that hpfp. Mine makes a noise but yours sounds very noisy.
I would replace it if it wasn't so expensive. As long as it's working I'm good with the clicking. Thanks for watching.
How did you initially hear it “splashing” without the relay?
How did u remove the ball joint with the Allen rench
I didn't that's why I had to replace them because I cut it off. The Allen wrench fit fine in the passenger side but would not work in the driver side. I found the upper arms with the ball joints cheaper than just the ball joints.
Buddy I just wanna thank you. I'm doing fronts on a Kia soul and forgot where the hell I put my big c clamp. Thanks for coming through🤟🏼
What the PART # For this Pressure Control B solenoid ? Part # ?
The only number I can find and I don't know if it's correct is 08105-2. That's the number on the top of the solenoid.
@@michiganmudmechanic awesome. It's a starting place ... Maybe it's the Number .. maybe not. But it's Something... Thank you for replying.
@@michiganmudmechanic Thank You For Replying
lol, "I'm not hammering on it, I don't do that. I mean not anymore". great stuff.
Thanks for watching
How long did it take for the entire project?
Best case scenario three to four hours. But I would give myself plenty of time to run into problems.
Talk about sidetracked 😅
Heat it a bit and use wax it will break loose easy af
Hell yeah brother
Nice video. As a fellow Michigan-der - I can relate to your statements about rust......not as bad as the north east coast but bad enough..
Ya those EGR pipes are notorious for carbon buildup…I think that’s y a lot of ppl delete kit them…I just did a head gasket in my speed6 dame 2.3MZR and my EGR tube was just as closed
2019 gas was .99 cents. Record profits come from record gouging...tactics of the rich.
GA 3.50 gallon
Don't do it, you'll fill up three times for the same amount of mileage with a tank of 87 octane.....pure snake oil taking your money.
Filled up Thursday in eastern NC at $3.19 for 87 octane.
Dammmmm. I’m going FLEX 💪
First to tell you<>Best friends in the world<>Hands down<>I mean<>Paws down
How to take the manifold out?
Gave up! Too much mumbling and no description.
What song is this?
All the music I used came with the editing software
Lol I love this movie. I’m not even a Democrat. 😅
What movie?
Cannonball run 2
At 15:40 you explain about harmonic balancer and that small electrical sensor, which you install. You say that it creates issues with misfiring? I have that misfire issue in one cylinder- can it be because of that sensor? What does it do and where it affects on?
I believe most of my misfire was coming from dirty valves. This is a very dirty running engine most direct port injections are going to be dirty running engines.
@@michiganmudmechanic ok. Thanks. I need to get aquinted to that.
@@arivaisanen4561 I'm really not sure what I did to solve my misfire. I replaced the PVC valve the head gasket cleaned all the carbon out of it and put new valves in it. Also when I look down one of the coil packs there looked to be a piece of plastic that could have been causing the problem the whole time.
Are the valve lifters hydraulic ones or do you need the adjust them?
Carbon buildup
What size is the line?
I don't remember what size the metal line was but I used 5\16 gas line for the repair. I don't think that this repair would have worked if it was on the high pressure side. Thanks for watching
The new motor came out of a manual car. I found what was left of a pilot bearing inside the crank. problem solved. 😀
Pilot Bearing
How did you actually get that cover off, I have remove all the bolts but can't seem to get the cover off do I use a pry bar?
Mine came right off after I got all the bolts out. I'm not sure why you are having trouble. Sorry I couldn't help.
Nice I just did one today I did not take the manifold out on the lift it’s easier
I do my best to not go under a car. A lift would look really funny in my 12 by 20 logistic hillbilly garage. Maybe someday. thanks for watching. Was the Mazda all-wheel drive?
Hello, greetings from Argentina, it also shows me p0777 but solenoid jam closed, is it the same problem? thank you so much
I would think so since it's the same solenoid. Just so you know this fix only worked for a couple of months. the transmission went completely out after that. There's a bigger internal problem and it's usually the pump. I'm gonna just replace the whole transmission with LKQ online used transmission. . I'm replacing the whole transmission because when pressure tested it's only giving me 50 lbs of pressure. This transmission requires anywhere from 75 to 200 lbs of pressure. Thanks for watching
I need a microphone like yours. Also I would like to learn how to put my scanner on the screen too. Nice work.
I got the mic off from Amazon. It's a Synco. They've been working well for about two years now. To screen record on the launch scanner you just swipe down on the top of the screen and it's in the options. My scanner is a launch X 431 pro V and the screen recorder came with it. Thanks for watching.
@@michiganmudmechanic I have a launch x431 too. I'll try it some time. Thanks
Had the same problem. Replaced everything except the brake hose only to find out I needed to replace the brake hose 😅
Did you reuse the old headbolts? Did they work longterm?
It's been awhile but I'd imagine that's a torque to yield bolt. It's a one time use so I would have replaced them.
@@michiganmudmechanic Thanks. I got spun rod bearings - would you drop the engine from the bottom or pull from the top on the CX7. Also would you pull engine and transmission together or split first. (Just in case you had any thoughts on the CX7 engine removal process).
@@pingpong9656 I have never pulled a motor out of a CX7. Mine was an all-wheel drive so just guessing I would have tried to come out the top or remove the front end. But I'm only guessing I do not own that car anymore.
They get their panties up in a wad about ram being maxe by fiat or whatever. Im like i dont give a fuck as long as she is 6 in a row. Ford made the 300, toyota made the 1jz/2jz, Cat the 3406, and the cummins 5.9 and 6.7 in different injection pump flavors.
Everything is made in China, even if it says it isn't
I loved selling old timers the AC Delco brand because they think it american, and then they get the package and its got chinese written all over it.
Detroit makes most if not everything in US
Thanks for the time in sharing great work boss🎉🎉
That is the oil pump from a design failure engine that is total garbage
Total junk mobile from the day of purchase
Make sure you use the updated bolt for the top one
Yes I used the doorman part number 917954 to replace the top bolt and plug. The original bolts that had to be replaced I found on Amazon using part number 11588522. Thanks for watching
Is that a 3.6l LY7?
2.4 ecotec
@michiganmudmechanic Not much better but I do know that the 3.6 V6 they come with has pretty bad timing chain issues so could be worse
I did the timing chains in my 2009 Cadillac 3.6. Two years after that the engine popped again. I tried the chaining chain fix again with no success. I did make a series of videos on the timing chain that failed and then the replacement of the motor itself. Which was real fun considering it's a all-wheel drive car.
Lol
Well he wasn't wrong
🤣
what year is this Jeep?
2012