Видео

What did you use for paint?

No glue on the blocks?

Love the hydra bucket action! Great content and attachment!

Hate to say this…. But I would have had that done a lot quicker with a sawzal and a 9” blade. This took too long , more work bringing the machine , plywood, hauling machine around town. Maybe if there’s more work for the machine I’d get it but this was excessive

Did you compare this to the blue diamond 4in1 bucket when you were looking? It seems to be a little heavier but is rated at two cubic feet more capacity

Love the Hydra bucket! This is the best!

You need a regular old oil filter wrench

Mine super tight too .

I have a Vermeer S800, OK machine, but the dealer in Perth Western Australia are full of themselves and offer shit service/ warranty, so I'm looking at other options, Kubota looks good but has an electronic dash which doesn't enthuse me, , I will likely go Bobcat. Thanks for the review. Also, when you're back blading/ levelling, use the cutting edge which is hard and replaceable. The back of the bucket will wear out doing that.

This was super helpful. Especially the commentary at the end. Thanks man!

Hey dude did you unscrew the screw at the top of the filter?

Man youre burnin a ton of oil

Is your fuel gauge broken or are you actually running the machine that low on diesel?

Do you think the 36" wide would have been a better choice? Have you encountered not being able to fit where you needed to with the 42" Do you think the mt100 would also handle the 48" wide model or do you think it would be to large? thanks

Hi, how wide is your 4 in 1 bucket? thanks

Right

I've NEVER seen a combination bucket used that way, thanks for the lesson...although the tree clearly gets damaged in the process I'm curious if you're going to replant it

Bow them in the middle with blocks Put both ends in then knock out the blocks. You made this way to hard with the method you used.

Hack

I’m selling mine. Too heavy and bulky

How long did this project take you

Great review, been in business 30 years own full size track machines. Only needed to rent a mini skid once in 30 years of business . To fill under a deck.

You helped me a lot. Thank you

This guy he dont know how do the job

Thats funny. Telling your guy to just run it through the paces while you go do some paperwork. Couple minutes later machine's in the office...your guy says "you never showed me how to stop it. Sorry boss, my bad. Where do want the key?"

1200 hours on our MT85. Kept waiting for something bad to happen but rolled the dice and came up lucky. Just added the 100 to the fleet and am looking forward to not having to grease the rollers - what a pain. Hope Bobcat fired that designer. Love your channel.

Do you still do you still have the 4 in 1 bucket? How long have you had it. Bobcat dealer told me they were having problems with

How much did it cost

Would you rather this or harley rake?

Everyone saying the MT100 is better than the SCL1000...at least it doesn't take 10 minutes to start draining the oil LOL.

Do you have a video about installing the lights?

do you have a video on that light you have?

you operating it in float mode?

get yourself a stump wrecker you could have popped those ushes out whole and about 30 seconds each

Great review

D-rings screwed to a 2x10 for strapping attachments down, broken straps tied together, your heaviest attachment 8 feet in the air, on a shelf that’s not even welded on the trailer, just bolted on the side rails. You’re going to hurt somebody. Quit being a scab and get the equipment you need.

Switch n go. In the heading thats why we click. Lot of wasted time,info and footage

Great video. Thanks

In addition to the impact gun, impact sockets are recommended too.

Couple of them seemed to be stubborn but got it done 👍 now you had it for some time I hear some people say it’s very loud fully throttled up ?

How long Did it take you to do this job

Would you buy this attachment all over again?

I have a 2009 Powerstroke Turbo Diesel F250 6.4 liter engine. At least as far as the location of the fuel filter and oil filter and oil drain plug, it is all the same as in this video. So, good job - this helps a lot.

Do you remember how much you charge for job

Thanks. Not too many videos for this, its very helpful. My front window isn't broke, yet, but the glass is really vibrating. Wondering if I need some of those clear protectors that you put on. Do they get put on the outside, or is there something else to stop the whole window from bouncing around when moving?

Is this grand rapids mi?

Hey man truck looks awesome 👏 I have 9 foot dump truck can you tell how much you paid for you sistem?

What about the rust beside the bonded glass how did u work that out without taken out the glass

Who in the absolute fuck welded the bolt holes instead of drilling them out? Oh my God that thing isn't going to last 2 years.

Poor placement of oil drain and filter. The more I work on this machine the more I see what little thought went into it.