Видео

How do I calibrate to use in bidirectional mode?

Hello! It can be programing even with the Bluetooth module?

3994 Kuvalis Path

Lakin Mall

Purchasing link: ztwesc.com/products/ztw-skyhawk-160a-hv-6-14s-sbec-for-rc-helicopter

Kayli Tunnel

Work it with Radiomaster?

Purchasing link: ztwesc.com/products/ztw-32-bit-seal-g2-300a-hv-6-14s-brushless-esc-water-cooling-two-way-speed-controller-for-rc-boat-surfboard-underwater-thruster

New generation Seal G2 300A HV 6-14S ESC: ztwesc.com/products/ztw-32-bit-seal-g2-300a-hv-6-14s-brushless-esc-water-cooling-two-way-speed-controller-for-rc-boat-surfboard-underwater-thruster?variant=44768965493050

Hi friend to configure the ESC with the board can we leave the motor plugged into the drive??? To sum up, we connect the programming board with the shortest wire of the ESC, we connect the LiPo and then turn on the ESC with the inter to modify the parameters.

Why only low, medium and high timing options?? I would like to have nuch more options. Cut off voltage same. 3.0, 3.2, 3.4. but i need 3.3. I expected much more options.

So you need three hands to calibrate the ESC. Also you failed to mention you have to let go of the throttle 3 seconds after you hear the double beep. This is what it says in the manual. I had to change radio to get this to calibrate. Didn’t like cheap radio

how to calibrate the two-direction mode

Does the Heli ESC have a built-in governor and soft spool up?

Hi . I have the skyhawk 125 . Now I have the R.B.W wire going to ch 3 for power and throttle. Futaba 16iz . 1:40 Now what or we’re does the other set of wires plug into . Do they go into the governor spot on the ikon2 . Thank you

Is possible to use for futaba 4 grs?

Bagaimana cara membeli nya ??

Hi I just got the ZTW 65 Skyhawks I can’t get the telemetry to work . So I need to or remove the yellow wire from the esc to the receiver thank you.

Does the yellow wire plug into the single on the sbus

your amps aren't working. I can't show amps either ?

Why not using PWM to trigger the single wire for SMR? Just how many receivers that has 2-stage output? NONE!!! It was a very bad design decision!

Im trying to do this same procedure, but I don't hear any beeps from my motor!!? I have the 40A esc.

please help, we have the same problem

Good afternoon, please tell me there is a problem with 40a ESC, as soon as the voltage of the 3S battery drops below 11.2 volts, the boat cannot go at full acceleration, when you push it to the end, the boat just stops and you need to release the pedal again and start again and do not press to the end. Thank you.

May i know what type of mcu used in the esc? Is it st32 or at32?

Love watching this. You should research "promosm"!

Sir kitna ka RC box ha price batana

I programmed like you showed me but when I let go of the trigger it goes on full break I can go full throttle forward when I let go full break and then reverse when I let go the neutral is now full break how do I fix this

So I programmed my 300 amp like you showed me but between forward and reverse is full break as soon as I let go of the trigger it goes full break how do I fix this or how do I bring it back to factory settings your help is appreciated

WooooW very nice amigo 🤟🏽😎🤟🏽

Can anyone understand this dude

Con il coperchio in carbonio non hai problemi con il gps?

Which motor is it

Hey mate would you be interesting in sending me a review unit for a comparison between this and a Flier ESC?

backsound not good 👎👎

Is the seal 300amp still pushing that mighty 3080???

On my ESC it just says Ready to connect ESC forever and won't program it!!

Terrible video long and useless and that had to be the worst install I have seen

Would it work with 1/8 beast pro 220a esc

Low voltage cut off does not work correctly on my 12s Beast Pro..... it always cuts off at 3v per cell (Sometimes lower!!!) and never does what I set it to using the LCD program box.

Hi what program card do you use on the Beast Pro 12s 300a esc? What’s the code for it? Thanks

The ztw 1/8 motors, are on sale on ebay $27 plus shipping! I bought 2, a 2150kv, and 1900kv also got a 150amp beast pro esc for 79! So a 110 doller combo! You cant beat that!

Any datalogged runs ?? A video , mehh nice and all.... But i want to see hard data collected with something like a Unilog with a 400A current sensor

How is this ESC Holding up ? You must demonstrate the boat going full throttle with the speed (GPS) to see how good the ESC is .

This video is a joke they are not showing any full throttle passes...that will show if the esc can handle the 12s.

I will be running Your ESC,s only with LMT 3080,,s so we will see just how good they are plus I'm running a true radiator with antifreeze through the Esc and Motor for maximum load protection

I'll be purchasing several of your 14s 300amp ESC thank you because I can save money on MGM ESC now is the ZTW 14s Seal 32 bit microprocessors? I know it has MOSFET what FETs and Capacitors are you using the cooling in the board is good and massive I will add 6awg to the ESC,s in the future upgrade the phase wire's MGM uses double 7awg phase wire's any 300 amp continuous must have above 8awg wires to be True above 259 amp's continuous 8awg wire gets hot fast.

Thanks for making a ESC that's in par with that Mighty MGM 40063

Where is this at it,s so beautiful like my hideout here in California

Thanks I'm going to buy a few of those ESC,s