- Видео 7
- Просмотров 38 985
Hani Sadek
Добавлен 3 окт 2011
LQI Control for Dual-input DC-DC Convert
Presented by Hani Sadek
Published in 2020 IEEE Transportation Electrification Conference & Expo (ITEC)
Authors: Abbas Hassan ; Hani Sadek ; Ali Bazzi ; Nasseem Daher
DOI: 10.1109/ITEC48692.2020.9161387
Conference Location: Chicago, IL, USA
ieeexplore.ieee.org/abstract/document/9161387
Published in 2020 IEEE Transportation Electrification Conference & Expo (ITEC)
Authors: Abbas Hassan ; Hani Sadek ; Ali Bazzi ; Nasseem Daher
DOI: 10.1109/ITEC48692.2020.9161387
Conference Location: Chicago, IL, USA
ieeexplore.ieee.org/abstract/document/9161387
Просмотров: 832
Видео
Part 5: Automating Plots and Parameters Initialization for Boost Converter (Matlab & Simulink)
Просмотров 1,3 тыс.4 года назад
Part 5: Automating Plots and Parameters Initialization for Boost Converter (Matlab & Simulink)
Part 4: Adding a Variable Input to The Boost Converter
Просмотров 5 тыс.4 года назад
Part 4: Adding a Variable Input to The Boost Converter
Part 3: Adding a Variable Load to The Controlled Boost Converter
Просмотров 10 тыс.4 года назад
Part 3: Adding a Variable Load to The Controlled Boost Converter
Part 2: Adding a two loop control (current mode and voltage mode) for boost converter in Simulink
Просмотров 18 тыс.4 года назад
Part 2: Adding a two loop control (current mode and voltage mode) for boost converter in Simulink
Part 1: How to build and simulate an ideal Boost Converter in open loop Using Simulink
Просмотров 3,6 тыс.4 года назад
Part 1: How to build and simulate an ideal Boost Converter in open loop Using Simulink
Power Sources Sizing for a Fuel Cell Hybrid Vehicle
Просмотров 2395 лет назад
Power Sources Sizing for a Fuel Cell Hybrid Vehicle
how can we calculate PI value for actual case?
Thank you for this effort, my question is how can I determine L and C in case of a PV Panel connected with a boost Converter
Thank you
how do we do for the buck converter?
how we do for the buck converter ?
values of PI how did you calculate it?
how do i reduce the load resistance from 5 to 2 Ohms? please guide
I think the load is not varied, but only change. Varied means be changed for a certain range, smoothly or in steps.
❤️🌹
Hi I liked your work can I get ur contact
How to combine two DC sources... The power at both is 500W, I want to add these two powers so I can supply to a load? How is it possible in simulink? Like I have 2 + and 2 -ve so I can get one +and one -ve
Great video
Very helpful!!
how did you calculate the values of pid controller
The values i used were just for demonstration purposes
can we use this controll strategy for bidirectional DC DC converter
how do you control the current in the case of a buck converter?
How to simulate pfc boost for current control
how did you tune the PID controller?
Those values were just used for demonstration purposes
how i can control three switches with phase shift 120 degree by using arduino uno to control 3phase interleave dc/dc boost converter can you help me please
To control three switched with a phase shift of 120 degrees you can simply use three pulse generators with 3 shifted phase delays (sec) based on your signal period. For example, if your period is 9 seconds, set the first phase delay to 0 sec, the second to 3 sec, and the third to 6 sec. Make sure you have the same period in three blocks. You can also adjust the pulse width to (100/3) or whatever pulse width you intend to use. To simply perform control using Arduino, you can upload your Simulink code to the controller that you have using the Simulink Support Package for Arduino Hardware. Get the add-on and you'll find everything you need in its documentation. You can also find many examples on youtube that illustrate the use of that add-on.
how can i ad an MPPT TO this circuit? i am doing exactly the same model but do not no what mppt can i use
Hello Haideryjumaa, unfortunately I have no experience with MPPT.
Dear Sir, very good content. Is the Simulink model available?
Hello Ankush Bissoondeeal, I have uploaded this videos long time ago and I don't have the models anymore. If you follow the videos step by step you'll be able to build the model.