Видео

I know it's about looks and style, but hose wide steps protect the vehicle from flying debris off-road. In all honesty, the make cleaning and drying the roof a breeze!

@@alp3781 ok?

@@mariarob Just don't see spending so much on a Ford, in general. But, enjoy the truck and as long as you are happy, I am glad for you. Hope the quality of the truck will not disappoint you.

@@alp3781 A lot of people say the same about Tacos. I have owned Fords since 1980. The F150 has been #1 PU truck for about 300 years. This Ecoboost engine is solid. All the "testing" reviewers rate the value of this Truck incredible for what it brings...400+HP/450TQ? You kidding me? Thanks

Where in S FL?

@@mariarob Miami and you? Looking to connect with other Raptor owners.

@@michaelpro2800 Pembroke Pines. IDK if you have joined but there is a USA Ranger Raptor Group on Facebook.

@@mariarobthanks did not know about it - I just joined

@@mariarob I joined thanks

Im going to make a video soon, but I have a 20v to 12v inverter by the back driver corner hooked to a 20v Dewalt. The single strand is wired to the passenger side using the extension wire going down and across, then back up the pass side. The Adhesive SUCKED. I had to use my own tape (Alien Tape). Thanks for the inspiration, and please let us know your first name.

@@BritoWorx thank you very much. Nice to get a positive compliment in a world of insults . Good luck. Keep me posted. Tune coming soon.

Dealer Install. It's in the description. Can get on Amazon.

Hi, thanks for the question. Check the diagrams and amperage...it comes up on engine search now. In the front...you can use 5. In the back You could use 4. I believe both of those are 15a

If you're referring to my front bumper, yes. I did PPF on the front bumper only.

Well, Ranger Raptor in My case but you're 100% spot on. I add and tweak little bits as I go. Thanks

www.f150leds.com. They are "generic" lights. I think made more for the big raptor. I modified the wires a bunch because they had thick material sheathing that I removed to allow a smaller hole to be drilled. The stick with 3M and when you pull the wires through, they stay. There is a tiny bit of "play" in the stickiness but they aren't gonna come off. The size of the the space is slightly too small for the lights so they do stick out a few mm's. I still prefer the look of these over the cheap Thai ones on Ebay that fit a little better but have the "little dots" showing on the lights instead of one nice "glow"

@@dom5956 McKillans® Car Pressure Washer... www.amazon.com/dp/B07VCMTZWV?ref=ppx_pop_mob_ap_share M MINGLE Pressure Washer Hose... www.amazon.com/dp/B0C26WNMF7?ref=ppx_pop_mob_ap_share UBERFLEX™ Kink Resistant Pressure... www.amazon.com/dp/B018H74H74?ref=ppx_pop_mob_ap_share Active washer anywhere Gun from Obsessed Garage. Upgraded blue model

I didnt know you can order with bed rail. I got a Retrax cover and Black horse bar put on by the dealer when I got it.

You got white with the decals? The banner I got from Lethal Performance, but I think you can find them anywhere.

So I contacted lethal performance and they told me they didn’t have a Ford performance banner for a Ranger raptor🤷🏽‍♂️

We're pretty pumped and we bet you are too! Check the status of your order by logging in to your account, emailing support@lethalperformance.com, or calling us at (877)253-8425 Monday - Friday 9:00am to 6:00pm EST! “Your Mustang, Faster.” img Ford Performance Windshield Banner - White/Red (2021-2024 Ford Bronco) - M-1820-BRR FPP-M-1820-BRR more detail $45.00 1 pcs That is the copy of the Email of the order!

It's not "FOR A RANGER RAPTOR" it's just a banner.

IDK anything about California, but it has hi flow cats so not sure.

You don’t necessarily keep the tracks the “exact distance” the entire length. If you widen the gap a couple mm on the fast part, the ball will sink down a fraction and slow down, making it less likely to fly off the track. I used segments of wire put through the tube, then I slid the tubes open and closed to get the desired width, then put a bead of hot glue on the hole where the wire entered/exited so that the tube stays in the that position. Hope this helps.

Keith Taylor you can't extrapolate times. Lentgh is not only factor. Track surface and degree of slope also affect speed.

It's the opposite for anyone reading. It's the x that gives rasp

Stop spreading false information it’s the X pipe that makes the exhaust raspy not the H pipe.

@@1456941 no it doesn’t, lol h pipe sounds like shit compared to an x pipe. H pipe is louder in a bad way, to much rasp compared to an x Pipe. I would I know since I’ve changed from an h pipe to an x pipe on all 3 of my 5.0’s makes it sound more clean.

@@christopher_5.034 Well take it from someone who made and welded BBK X & H pipes for 12 years and you are absolutely wrong. The x pipe gives better flow which equates to just a little more hp but yet make it raspier while the H pipe gives it that more muscle car sound & deeper tone, Fact..,

@@1456941 bro I don’t give a shit what you did for however long, from my personal vehicles X pipe has always had a MUCH cleaner sound than the H pipe period. If it’s your preference to like the h pipe then more power to you. To me the x pipe is less raspy and more clean than an h pipe.

When you removed the cats and added the 1-7/8 headers, the sound was nice, but I didn't like it from the inside. The GT500s allow the outside sound to stay really nice but keeps the inside to a quiet, pretty "roar" without drone.

No Drone since I have the GT500 AB..I did have it with the Borlas

No Drone since I have the GT500 AB..I did have it with the Borlas

The tiny finishing nails go through the poly tubing from the sides (so as not to affect the ball rolling) down at an angle into the wood.