Видео

I know it's a long time since but i hope you're not harmed, you forgot to stick an axle stand under the vehicle. Please don't just rely on the jack.

Great video Chris, keep em coming mate.....👍

I recognise the cameraman's dulcet tones.😂

Fantastic video the car sounds healthy. I am also building one on my RUclips channel

Great video.

Looks good but what was the reason for not carpeting the wheel arch first?

Looks lovely. Where was the material from ?

For £20 I was expecting Karndean flooring.🤣🤣🤣🤣

Who's your glamourous assistant. Going abit thin ontop :)

Floor makes a hell of a difference. And is that Mr Hughes helping or a very good look alike 😂

Great content. I’d been wondering how much work I’d be able to do with the engine sitting on a furniture cart, and you pretty much answered that. I’d also been wondering how easy it was to get the engine tins and rubber seals lifted back into place (and the axles aligned) - you showed slightly more than other videos, but I’ll forgive you since it looked about midnight when you finished. ;) Cheers from Colorado.

Morning Chris. Just spotted the video. RUclips hadn't recommended it to me! There's an online calculator (somewhere...) to calculate the wire thickness needed based on length of the wire run, amperage, and maximum desired voltage drop. Its particularly useful on canal boat builds. Even model boats...😂😂. Fridges are known for switching off when voltage is too low caused the supplying battery voltage dropping but critically by the use of wires which are too thin causing excessive voltage drop. Sure you know all that but makes for instructional comment!😂😂😂

Thanks for the Video, good information greece is such a shithole

Nice job mate. I put mine under the seat too. I think carpeting your seat bases would finish it off nicely. ruclips.net/video/_zNZYu5l3wU/видео.htmlsi=sUAsPY9ZO-X3M3_q

Great video. Did you squeeze in some grease on cv joint before reassembly or were you cleaning edges?

I like wiring. Ground side switching quite common in cars isn't it? I understood the diode use. That relay looks familiar. Did we consult? No, I can't remember either.😂😂

How much money do people charge for this job? Thanks

Great vid. Where is the speaker located in the van please? Thanks

Any updates !!!!

well done and thank you very much for this great video i fixed it with your help thanks a lot

So my cable box is covered in sticky foam so I can't identify the numbers. Which 8s the reverse light wire colour. Forums say green. But I have green and purple and a green and yellow so very confusing

Sure ...its lite bite left😅😅😅...

Can you then just clad over this without any other insulation?

Great video! Good to see its still helping people 4 years on. This has helped me with my coilovers recently. Can I just ask, could you damage the drive shaft or any of the bearings in the cv joint in the process? I struggled to release the ball joint and really had to flex the wishbone down putting pressure on the boots and the drive shaft moved back and forth many times during the process. Im not sure if its in my head and its road noise, but im sure i can hear a rotary noise that sounds like the wind if that makes sense? It might just be paranoid and listening for something because ive never done anything like this before. Thanks again. 👍

Looks the nuts.the rubber washer is to prevent galvanick corrosion. Steel van aloy shokers

Hi did you remove sensor ta

Cracking video, just about to undertake this myself and am much more confident after seeing you run through it. Just a quick question, do the brake lines that run from the ABS unit to the rear brake bias cross over at any point (in the bay, or near the bias)? I've just replaced my lines but comepletely forgot to take a picture of them.

Sorry for the dumb question, do you work on the wiring when the van is off without disconnecting the battery and when you put the van in reverse you used a multi meter to find the cable that would be dead but in reverse showing 12v. to connect this to?

whats the right tool to remove and put back those wag clips? Been struggling with one for an hour...xD

Hey everyone I’m wanting to rebuild 07 GTI calipers and wondering what they’re called and where I can buy little rubber seals for rear e brake. I have front and rear pistons seals but having trouble finding info on e brake ones. TIA!

Very good video. So many points I didn't know. Thanks.

0:19 SEX 🍆 😂. Thanks for the video. I'm about to change the speakers in mine.

Okay so i manually took 12v from fog light that enables on key ignition and put onto black wire, and rest of your video I seem to get the same except the coolant sensor i get on specs. But my ISV is still not reacting! What could be wrong? I have jumped the isv while connected and bloody hell it noticed it works then, revved like crazy

Absolutely brilliant video. I'm convinced. Thanks a lot pal.

Thanks for your video. By far the best one for me on ply lining a van.👍

Thanks

I thought the M.o.t. was every 2 years in greece ?

Having issues with mine and this has helped with where to start! Cheers 👍

😂

Its summer, so heated seat essential in in the UK. Conveniently located power supply!! Short cable run. Fused I assume?👍😊

Is that not going to annoy you being different to the passengers side or have you a plan?

Interesting video. However, these head units apoear to be made in China. That country is guilty of atrocious war crimes and crimes against humanity. China is also launching cyber attacks against our hospitals, schools and defence infrastructure. They're also supporting Russia and are supplying them with arms, military components and expertise. I'll be looking to buy a European made head unit instead, if I can find one ...

Great video ,enjoyed the porcshe content 👌

Worn out watching the race and thats just fifteen minutes. Well done.👍

You made fitting that headliner a hard watch... use a bigger table, it would be so much easier for you. ALWAYS use oversized pieces. I get that its expensive, but if its trimmed within millimetres, it will shrink and pull itself apart....

BIG TIP, when the inner metal sleeve is removed from the bush remove the blade from a hacksaw, put blade into the old bush still in the wishbone, reattach the hacksaw to the blade and cut through any rubber left the through the outer metal part of the bush taking care not to cut into the wishbone itself, when cut through hammer and punch will knock out the old bush relatively easy.

Me watch, me scared to do hehe! Great work!

Rivetting video. I mean clipping video.😂😂😂. Looks a good finish on the roof, be interesting to see it face to face. Where did you source the suede with foam backing? A trim shop or general ebay market place msybe? Seven days and counting....👍

Great video as usual ,like the clips .well done.