Видео

Hi, Larry! I can do that with the following equipment aside from your Starlink basic kit: - Starlink ethernet adapter (assuming you don't have the v.3 or above unit) - router (I'm using the TPLink ER605 - Omada OC200 to manage your voucher wifi setup - a POE switch (I'm using aTPLink T L-SG2210MP switch (8 POE ports and 2 SFPs) since I have a lot of APs distributed in our dwelling). In your case, you can use the SFP to connect other houses that are as you said at least 1000 meters away from your house. An alternative is to use outdoor wireless bridges (e.g., TP-Link CPE720) in a point to multipoint configuration. This way, you won't have physical breakage problems that could happen to fiber optic cables. - for wireless remote connection, you'd need a TP-Link CPE720 + EAP225 in each of the remote houses that you want to connect to your central site - for FOC connections to your remote site, you'd need a media converter that would connect your FOC to your EAP225 Hope this helps and good luck on your endeavor!

Hi po, Sir Albert! Ano po ang ina-adopt ninyo po sa Omada po?

@@Japzel mayroon na po, nakuha ko po ay yung TPLink Kaya Smart Plug with Energy Monitoring. Ang problem lang po ay mabagal po ang power switching nya po. Nag-rereset po ang buong wifi system after a remote power toggle po. Thanks just the same for your recomm po!

@@TitoJaksVlogs dimo na need e remote yan, lagyan mo lang schedule ng oras or yung sunrise and sunset na auto on and off. And yes TAPO is under the TP-Link brand parin.

@@Japzel sige po, Sir. Test ko din po yung scheduled toggle po. Thanks po! 🤗

Hehe.. Thanks much, Wilbie! ❤️

@@telstraaquinaz5802 thank you po!

@@yourrandomlifehacks this shall be done. ❤️

Sure, here's a step-by-step guide starting from connecting the Starlink to your network, including the TPLink ER605 router, TPLink SG2210MP switch, Omada OC200, and TPLink EAP225 access points: 1. Set Up Starlink Router: Initialize Starlink: Set Up Starlink: Follow the instructions to set up the Starlink dish and router. Ensure that the Starlink system is operational and providing internet connectivity. Enable Bypass Mode (Optional): Starlink App: Open the Starlink app on your mobile device. Bypass Mode: Navigate to the settings and enable “Bypass Mode” to disable the Starlink router's built-in routing and Wi-Fi functionalities. This step is optional if you plan to use the Starlink router for routing; otherwise, it allows the TPLink ER605 to handle routing. 2. Connect TPLink ER605 Router: Connect to Starlink: Ethernet Cable: Use an Ethernet cable to connect the Starlink router’s Ethernet port to the WAN port on the TPLink ER605 router. Power Up: Plug In: Connect the TPLink ER605 to a power source and turn it on. Initial Configuration: Access Router Interface: Connect a computer to the ER605 using an Ethernet cable or Wi-Fi and access its web management interface (usually 192.168.0.1). Configure WAN Settings: Ensure the ER605 is set to obtain an IP address from the Starlink router (typically set to Dynamic IP). Configure LAN Settings: Set the ER605’s LAN IP range (e.g., 192.168.0.x) and configure any additional network settings. 3. Connect TPLink SG2210MP Switch: Connect to ER605: Ethernet Cable: Connect one of the LAN ports on the TPLink ER605 to any of the non-PoE ports on the TPLink SG2210MP switch. Power Up: Plug In: Connect the SG2210MP to a power source and ensure it is powered on. 4. Configure TPLink SG2210MP Switch: Access Switch Interface: Find IP Address: Determine the IP address assigned to the SG2210MP (check your DHCP server or use a network scanner). Login: Open a web browser and enter the IP address to access the switch’s web management interface. Default Credentials: Log in with the default username and password (usually admin for both). Initial Configuration: Set IP Address: Configure a static IP address for the switch within your network range (e.g., 192.168.0.2). Subnet Mask: Set the subnet mask to 255.255.255.0. VLANs (Optional): Configure VLANs: If needed, set up VLANs for network segmentation. Assign Ports: Assign the appropriate VLANs to the switch ports based on your network design. 5. Connect Omada OC200 Controller: Connect to Network: Ethernet Cable: Connect the Omada OC200 to one of the non-PoE ports on the TPLink SG2210MP switch. Power Up: Plug the OC200 into a power source. Access Omada Controller Interface: Find IP Address: Find the IP address assigned to the OC200 (check your DHCP server or use a network scanner). Login: Open a web browser and enter the IP address to access the Omada Controller’s web interface. Initial Setup: Follow the setup wizard to create an administrator account and configure basic settings. 6. Connect TPLink EAP225 Access Points: Connect to SG2210MP: Ethernet Cabling: Connect each TPLink EAP225 access point to one of the PoE ports on the TPLink SG2210MP switch. The PoE switch will provide both power and network connectivity to the EAP225s. Power Over Ethernet: Check Power: Ensure that each EAP225 is receiving power and connected properly. Check the status LEDs on the EAP225s. 7. Configure TPLink EAP225 Access Points: Adopt Devices in Omada Controller: Open Omada Controller: Log into the Omada Controller interface. Discover Devices: Go to the “Devices” section and find your EAP225 access points. Adopt EAP225s: Click on each EAP225 and adopt them into the Omada Controller. Configure Wireless Settings: Create SSIDs: Set up SSIDs (network names) and passwords for your Wi-Fi networks in the Omada Controller. Configure Security: Choose security options like WPA2/WPA3 encryption. Voucher Wi-Fi Setup: Enable Guest Network: Go to the “Guest Network” or “Wi-Fi” section and enable guest network features. Configure Vouchers: Access the voucher settings in the Omada Controller to create and manage Wi-Fi vouchers. Define voucher types, expiration times, and usage limits. Optimize Settings: Channel and Power Management: Adjust the wireless channels and power settings for optimal coverage and minimal interference. 8. Verify and Monitor: Test Connectivity: Check Devices: Ensure that devices can connect to the network and access the internet. Wi-Fi Coverage: Walk around with a device to test signal strength and coverage. Monitor Network: Omada Controller Dashboard: Use the Omada Controller to monitor network performance, manage devices, and make adjustments as needed. Regular Maintenance: Check for firmware updates and back up your configuration periodically. By following these steps, you’ll have a comprehensive network setup with your Starlink connection, TPLink ER605 router, SG2210MP switch, Omada OC200 controller, and TPLink EAP225 access points all working together seamlessly.

@@DrivingPhilippines thank you, Sir/Ma'am, for appreciating our dream in sharing our blessings. I'm sure you'd do the same given the opportunity po! 🙏

@@DrivingPhilippines BTW po, the area is not air-conditioned. The temperature of the equipment inside is still ok to the touch. The hottest of all is the Starlink router, second is the TPLink OC200. Router and POE switch is cold to the touch.

Thank you po!

30 watts per bulb lang po sya. Di naman po gaano kalakasan for my usage po.

Malakas po ang kapit per magnet. Bale apat na magnet pa po sila. Di rin po ako tumakbo ng mabilis po. Thanks po for your comment! <3

Nice test kuya Jak! ❤ it’s calling for a low profile roof mount mod for long distance travels. I love the setup overall

@@TitoJaksVlogs Thanks for sharing your setup. May I ask where you purchased the magnets?

@@georgemanny Hi, Sir! I've posted the links in the video description po. Enjoy your own trips with your SL, Sir!

I'd fix this sa house as backup to our fiber connection. I'm ordering a Gen 3 for a low profile setup. 😁 Thanks, dear Bro! 🥰​@@CreativeEngineeringChannel

Hi po, Sir Lecky! Naka-recta na po ang MPPT charger sa battery po. So wala na po need tanggalin po. I also ensure that I'm charging via solar or via AC power and not at the same time po.

Thank you po!

Hi po! Mayroon naman na Spigen screen protector na puede po dito. Ang magiging concern nyo lang po e yung fingerprint sensitivity po ng unit nyo. You may need to adjust it po. I don't install screen protectors in my units precisely for that reason po.

I bought mine from Alibaba. 🤗

I got mine from Alibaba, Sir!

How long did it take to get here with Alibaba

Around a week po! 🤗​@@jermaudeearl

Hi! I understand that the "i" model includes a built in power supply. The one without the "i" needs an external power supply.

Like the one in the pic: gxpumpofficial.com/collections/gx-cs-1-3/products/gx-cs3-pcp-air-compressor

@@TitoJaksVlogs Thank you!!!!

Nope po, Sir. Am not a fan of tempered glass protectors so as not to hamper the onscreen fingerprint sensor.

@@TitoJaksVlogs i see, mine using the Samsung TPU cracked after accidentally falling off my pocket hitting the ground screen first, will try again the Whitestone. thanks

@@iansantos7808 You're much welcome, Sir!

Hello ​@@iansantos7808 Do you use this case with the Whitestone Dome tempered glass?

Bought it here po: www.quadlockcase.asia 😊

Yes po. Hindi nga lang po masyado mabili ang charging but yes, it will still charge.

Thank you, Anak! <3

I fondly remember I would accompany him in his work duties before, Anak. <3

Will do with gusto, Anak! <3 Thank you too!

Thank you, Akie! <3

OBR- ❤

Ride tayo soon, dear Bro!!!

Haha! Eagle eye! You're the only one to catch that, Sir! Thank you! Shall be amended sa post, Sir!

Incorporated in the captions, Sir! Thanks once again! <3

@@TitoJaksVlogs Welcome Sir. Taga dyan po kasi ako sa baba ng Cali 😎

Haha! Will do, Sir Sam! <3 Isama natin ang bike review ni Sir Antz din!

@@TitoJaksVlogs abangan ko yan! :)

Thank you, Sir! <3

Thank you! Subscribed to your channel, Sir! :)

Thank you po!

Would love that, Bro Antz! Huwag mo kaming iiwanan! 😅

Let us know when you'd be back sa Pinas! 🥰

Pinas na ako since Sunday

Sige, sama ka sa amin sa Baler, Bro!

Hi, Sir! Maaari ko po kayo tulungan via messaging po. Halos lahat po ng materyales ay nabili ko po online. Links po ay nasa video description. Taga saan po kayo, Sir Ernesto?

Yes po. Ikabit ang solar panel output with correct polarity sa input ng MPPT. Then set the output voltage to 48v sa MPPT po. Instructions are in the manual po. More power to your project, Sir!

shp.ee/cfqx4nf

Will do this in our future videos, Sir! ;)

Bahay muna po! 😅🤣

Here, Sir! shp.ee/cfqx4nf

❤

Thank you! 🤗

❤

Would love that, Anak!

Sige!