Видео

Ohhhhhhh Thank you! My angel is falling down no matter what I do! Merry Christmas.

Great looking house. You definitely know what you're doing - starling resistant entrances, nice big cavities, nest trays, and easy compartment access. Great work!

I know this video is 2 years old by now, but I just watched it. The Parker website says: "Please note the couplings on these fittings are only intended for use on hoses that have not previously been in service." I wonder how you feel about that precautionary statement. The hoses on my motor home are at least 8 years old, so I am concerned that the hose might fail at the fitting due to its age. The hose in question is 20 feet long, so I would much rather cut out the section with the leak and repair it, rather than replace it. Thanks for a great video.

I feel like I have stumbled upon some Illuminati special knowledge here, worked like magic!

I use the same connections on my car haulers made by Cottrell trailers in Gainesville ga . They sell them OTC.

If someone still watching this video, you need Lithium based mineral NLGI1 grease for the bearings. Do not use EP grease, it has Sulphur as additive and wears faster the bearings and the wipers. For the rails use VG68 mineral oil for linear rails. Don't use silicone oil, it's incompatible with the mineral grease you injecting in the bearings.

What is the center finder app?

My new tent just broke so this is going to save my small business some money. Thanks!

You solved my iMac repacking Tetris, thanks!

I sure do love Cedar Key. There is nothing else like it.

Great video. It was just like that before the storms. It got hammered last time. Lots of rebuilding has gone on. Thats a good thing. Time to get back to visit, Shrimp and fish straight from the gulf are my favorites. Good eating, right there.

I did exactly this, took 20 minutes, and it works great! The parts were perfect and worked exactly as described. Thank you for the save!

WOW, I used a towel because I thought it was going to be a lot harder to rip it out after locking it in the drill.

EMI interference can cause this

Hi, for me the bit broke and when i put in a new one, it didnt spin again... did you find a solution?

I went to the distributor to get this coupling, but it would not fit my 2006 Beaver Monterey line. They said the coupling only works on Parker hoses.

Extremely helpful

This worked for me! Thanks!

You mentioned that the new Parker part # 2-651-r-4-4 will not work with older hose. Can you please elaborate? The original part# 20651-4-4 is no longer available anywhere.

You’re an absolute hero! That never would have occurred to me!

What kind of saw is that and what size? I know it's a Dewalt... but... I need one Exactly like it...

OMG! thank you so much!!!!!!!!

Nice tip! Now I only need to build a router table ;) Tabs can also be removed with a band/disk sander, and it can finish the edges as well.

Wow, an old Sears Craftsman, tilting head bandsaw.

Thank you...straight to the point! I went through 3 other vids.

This would be great for the apartment life if I had something like this El Cheapo table for now until I get me a sturdy skid table made and that way I can have a can crusher device in my apartment that don't make a whole lot of noise this would be perfect and make it to work to fit all different size cans in there that will be awesome whoever made this did a great job

You did a great job in explaining what you did. I was going to comment on the dimensions but you did give them at the end!

Thanks, very helpful!

I had to have a new hose made. Could not find the fittings. With the 7/16 JIC female and 1/4 hose end and 153" of hose, I paid $132. If I called Exotic Automation and gave them your part number would it fit my camper leveling system hose and the 7/16 JIC female?

Difficult to find a better reason for cutting wood, than to bring a little joy into the lives of sick children. 👏👏👏

Sincerest respects for what you are doing.

Very nice project Cecil. Did you design this yourself and do you have a file for this? I would love to try this project myself.

WOW! Thanks! Worked perfect!

Would you provide a idea of what the floor cost you?

Hell yeah ty.

I just did the same setup and wondering if you found a way to manually run the speed controller?

How did you add a MYPOST PROCESSING folder or how did you do it. Also how do you get the MY POST PROCESSORS to show up when going through list of setting up a cut? Thanks Hager

Nice, this is what I am looking for. It would be great if you can show how you prepare the toolpath in VCarve for a tapered cut.

The image you provided is blurred.

Cecil, your filming of the screen is blurred + no one wants to hear your issues when viewers want solutions to their issues.

If you put something as a fulcrum under the pivot of those Klein cutters you’ll get more lift per grab. If you use a stiff back broad knife or steel junction box cover under the cutters you can get a nail out without marking up the surface of a piece your trying to reuse

Dear Lord, this saved my butt. My mom had one of those stands for the angel that was cylindrical, like a toilet paper roll. i wadded up some tape to keep some two-pronged metal stakes ( like giant, U-shaped paper clips) locked in place...Slid right down and didn't budge. Thank you for the idea! You just saved me a giant headache.

how i can contact you sir?

very nice video sir😍,to rank do seo to your video😊

amazing video but not for seo your video dont rank

The end that screws onto the hose are left handed threads (counter clockwise rotation to install) . In the video you are rotating the wrong direction and that is why it is not going on the hose very well.

Thank you so much! I cut some really pretty dead tree wood down and it is thin enough to put on my miter saw.

Brilliant thank you

Thank goodness for this video. Worked so well.

I removed mine, but now I can't get the bit back in the magnetic bit holder.