Видео

What bout the shocks

I've seen the bigger kit for 150. What do you think of that one?

A scanner code number tells you the circuit that is giving the code , so like a engine temp sensor code tells you that circuit is doing it , not necessarily the sensor itself .

Dude. The scanner works properly. Tte problem as usual, is the ignorant monkey behind it…

Please don't think I'm trying to be rude or nasty, but I don't understand the point of this video. I have 3 scanners and none of them say "this part is bad/replace it". They all show the codes that are either pending or history. Some scanners will show a list of possible problems that could set a code, but I've never seen one that told you what is definitely wrong with it.

I never go on what the customer says and start diagnostics from scanning for codes to get a general idea where the fault is and troubleshooting the electrical wiring or modules involved with the code. What I hate about cheap bluetooth scanners is they want you to pay them more to unlock features of the software. At that point, you can just have AutoZone scan for codes and if the guy behind the counter is knowledgeable, he can point you in the right direction. Had a friend bring his truck in to have a code scan done. The guy scanned it and the code popped up that all banks were lean so he troubleshooted with us by saying whenever he sees that code come up, there's a vacuum leak somewhere. We found out that one of the rubber hoses rotted away and was setting the lean code. Sometimes the computer will think the MAP sensor is bad because it's not reporting proper vacuum from the manifold. You always start out by diagnosing the problem because the customer can steer you in the wrong direction wasting a lot of time. It's happened to all of us. Good luck and thanks for the information.

i had replaced my acura MDX odometer then i purchased an OBD scanner with Odometer correction from AMAZON. i had to return the unit. it does nothing as they had described. then i scanned my neighbour honda civic he had check engine on and also that 700$ OBD scanner did not find anything even after the updates that i had installed. good thing i had purchased it from AMAZOn so i could return it.

Glad you are making progress

Me and my dad hate squatted trucks and watching this video gave me the idea to squat his truck for his birthday next week lmao thanks for the tutorial though

Did u have any issues with getting an alignment?

Very practical installation sharing. Thank you, Hayden!😊😊

This is cool

thanks for the coming out tutorial.

NIce. Are you interested in vehicle lighting stuff sponsorship?

Do you know if the 2500 pins will work or the newer longer alignment pins? In a 99-06?

Nice video buddy🤟🏼

Get you some small like half inch blocks so you won’t rub so bad I bet your hard rubbin

Thanks for getting this diseased alabamothy dookie fest off the street.

I swear when squatted trucks get banned I’m going to be so happy

quick n simple,appreciate ya gang

Thanks for the video, with the leak, do you think it is rings, valves or seals? Frankly at 300K, I think it's not bad...a lot of engines won't last that long!

For everyone asking the drop brackets for the UCA they come with the lift kit. I just got done putting a 2.5in level spacer on top of my 7in rc lift just like this video and my truck rides terrible and is super bouncy now almost to a point that its unsafe. However I was still running factory UCA. I ordered the rc UCAs hoping that will make a difference? Will put on new UCA and get alignment and see if i get back the ride quality i had with just the 7in kit

Hey man I have a 15 Tacoma and wanting to install a 3.5 strut and upper ca is it possible to install a 2 inch puc on top of the 3.5 strut??

Real men dont squat

stupid ass video made no sense 👎🏻👎🏻

Hey man, I’ve got a 2011 Silverado with a 7.5 rc and I want to bring the front up some more. I ordered some cognito uppers and Ige got a 1.5 and 2 inch front lower strut level. Which do you think I should add. I know angles will be bad but do you think I’ll be able to do the 2 inch or should I just do the 1.5

Can I stack a 2 inch front lvl kit on my mcgaughys 9 inch lift?

I got a 2014 , with the RC 7.5 and a 3" leveling spacer, (2wd) truck is been doing fine for almost a year now

If mine is already set at 9 can I still do this?

Where did you get them drop brackets that your control arms are bolted to?

Ok was the strut set at 9 inch when yu stacked it or at 7 inch?? Thank you

Do you do side work

Nice

Where you get the control arm drops??????

Is this bad on your shocks like would it be better to put my stick rear shocks in?

I’ve got a 2000 Silverado with 206k on it and I’ve noticed I’ve got gas in my oil I’m thinking it’s injectors but I’m not 100 percent fr

i have a 2014 silverado with a 3” level and i want to add a 5” or 6” lift kit, would this work?

Do you need to have drop shackles or can you just take the 6 inch blocks out the back just like that?

Great video !

Yo so here’s the setup homie 2011 Silverado 4WD with a 6” RCX I’m gonna throw a 3” level stack on the front but the real question is where am I gonna get a 9”rear block for the back? rear N3 shocks are rated for a 6”-9” lift so we’re good there. The main question is I’ve found an 8” rear block to run in the back do you think it would level it out pretty good to where it’s not noticeable? Running moog tie rods and rough country UCAs

So I got a 6 inch lift on my truck and say I took out the 6 inch blocks and put 4 inch would it have a baby Lean to it

Don’t really know why you time lapsed everything. Would have been nice to see you actually do the work.

Fine job, sir, good information

where did you get the control arm relocation brackets from

good information

What gauge wire are you using ?

We have 7/9 mcgaughys whit uper control arms cognito i want put 3” spacer u tink need the ball joint spacer for alignment

Is that a 6.2

What soap brand did you use

Is the visibility still good or is it difficult to see what's in front of you