Видео

Love to know what a tiny pair of vise grips are needle nose regular?how do you reach the clip, how do you reinstall the clip?

how the hell are you supposed to get the clip in

This is a self bleeding system. All you have to do is set the throttle to full and crank it and it self bleeds the air out of the system.

how connect the spring on the pump

This is so awesome

Can you adjust the fueling on these pumps?

Throttle control is external. Fuel on/off is internal.

Say , where is your other video

My pump appears to be leaking but is working fine. Any tips?

Carl Larson was my great-grandfather. His sister Hilma was married to William Cline.

Matt Estes? more like ma testes.

Any update

I too went with an NH TC35, 03 shuttle shift with 1000hrs. Love love love it. I got one with grapple, already had 3rd function kit installed. I lifted a log half that heavy and realized the bush hog or tire ballast needed to be on. The 16LA loader sits out pretty far from the unit which is nice. It’s capacity is just fine. I’ve ran my share of T175s and T190s and would say the TC35 is close as far as lifting, speed with the shuttle shift is another story but like you I’m not solely using it for one purpose. Good luck hope you still own the TC35.

I’m redoing my transom in a 1448 johnboat and I was thinking about leaving the bracket off myself I’m glad to see you thought the same thingAnd I’m going to add a quarter inch piece about 30 inches across to mount the supporting brackets that go to the floor both sides that all to increase the Strength

Operator should back drag material.. even with a brush cutter. But at $80/hr you get what you pay for!

I have to send my injection pump out to be checked. Who can I send it to that is reasonable? It is out of a TC45 4 cylinder.

Did you ever figure out if it was suppose to move when you hit the throttle I am in the said situation and with a new pump I have no movement with throttle

How do I install it (shim it) to the cover properly?

Hey i know him

I have same problem. Did it get fixed?

Same issue here. Still working on it.

This video helped me big time. I looked all over RUclips to find my exact pump and finally found you. Thanks a million

I am using 80 hp tracked bobcat this coming tue. to clear 12 acres of brush ranging from 4' to 8' tall and from 12" to 2" diameter I have been using a quick attachments LO-flow rotary cutter and pretty disappointing on tue I will be demoing a 71" diamond open front cutter, they said I should be able to clear the entire 12 acres in 1 day, I hope they are right!

Thats my Cary

nice place!!

what's the biggest log you have had on it?

it's really hard on the planer to operate without a dust collector. the chips get recirculated and slow the process down.

Why don't you buy a dust collector, your lungs will give up, after so muck dust inhalation. I leave in California, where a lot of folks are selling their equipments because lungs problems.

a dust collector is a must. your just recirculating fines in the cutterhead and griding them into the board face. also sounds like your rollers are out of range

Either your taking to much in one cut or its not adjusted right, that planer shouldn't need any help to push it threw..

why not joint the boards 1st????????

Thanks for uploading this, Cary!

THE ONLY THING GROUND SHARK NEEDS IMPROVEMENT ON IS THE CARBIDE CUTTERS THEY NEED TO USE FULL FLANGE STUMP CUTTER CARBIDE

GO WITH GROUND SHARK HIGH FLOW ROTARY CUTTER AFTER 200HRS STILL CUTTING AND MULCHING

DO NOT BUY THE BUSHMASTER HEAVYDUTY ROTARY CUTTER ITS ONLY GOT TWO GOOD THINGS ABOUT IT THE DRIVE MOTOR AND THE DECK BUT THE TOP SIDE OF THE DECK NEEDS IMPROVEMENT BOTTOM SIDE OF THE DECK I LIKE NON MULCHING FULL DISCHARGE

I CHARGE 150-200 PER HR FOR ONE MACHINE CHAIN SAW WORK I CHARGE 125-150 HR

DO NOT BUY A DIAMOND SKIDSTEER ROTARY CUTTER THE ONLY THING GOOD ON IT IS THE BLADES AND FLY WHEEL

ALWAYS SPRAY TREE KILLER AFTER WARDS DUMMIES

I HAVE RAN THE BUSHMASTER LIGHT CUTTER A LOW FLOW UNIT TWO BLADES NON MULCHING DECK HOOKED TO A MTL 25 AND GOT A BETTER MOWING RESULTS THAN THIS AND I HATED THE LITTLE CUTTER WENT THROUGH THE LINE OF HEAVY DUTY ROTARY CUTTERS THE GROUND SHARK IS THE BEST

This air dried white oak is hard. Pushes the grizzlie planer to the max. Band sawed boards have some variation in thickness. 1/16 pass seems to the best way to reduce thickness. Final pass was consistent and smooth. Early passes were PNA.

Boa Maquina!

You should be able without pushing or getting stuck. Also use entire blade, middle, right, and left to wear blade even. I usually run and stack on top. Your blades dull?

my colleague actuallly has owned this Skid Pro mower for over a year. No problems,beast of a mower for the dollars

This mower annihilates anything under 3",diameters of 4 to 5 are within the limits of the cutter but acre/hr production is reduced considerably. This is the cheapest way to mulch small acerage under 7 acres and supplement with some chainsaw work on the larger diameters over 5 inches. This particular tract took about 2 hrs per acre with the larger trees still standing. Rate of production is directlly related to the size of the trees.

Invest in a dust collector system.

I paid $80/hr not counting trailer time

What can one expect to pay an hour for one of these and an operator?

That's my dad that scored

well that thing puts the little 13" planers to shame haha

Stereo sounds good