- Видео 135
- Просмотров 85 004
The Machinist
Кувейт
Добавлен 30 май 2011
Benjie Orcuse Tebelin official
Creatively is best to succed!
Skilled Machinist - Oil and Gas drilling maintenance
Do: mechanical parts fabrication
Machining,turning,threading, drilling,repairing spare parts.
Do making Jigs and fixtures
Minute crafts, ideas for newly machinist
Hobbies singging,collaboration,
Life changing encouraging videos
Creatively is best to succed!
Skilled Machinist - Oil and Gas drilling maintenance
Do: mechanical parts fabrication
Machining,turning,threading, drilling,repairing spare parts.
Do making Jigs and fixtures
Minute crafts, ideas for newly machinist
Hobbies singging,collaboration,
Life changing encouraging videos
How to re-store broken bolt with a tilted milling head @ 55 degrees
Iron roughneck slider/graber. Has broken allen bolt located on the angled side,
Work piece clamp on the milling table, X Y Z axis was locked in position.
Only the milling head spindle moves up ang down
Miliing head was setted to 55 degress angle
And performed drillng /oversized the hole
Threading with 1/2 UNF tap
Inserted with threaded 1/2 UNF stud bolt
And drill with required tap drill size for making the original tapped hole
Work piece clamp on the milling table, X Y Z axis was locked in position.
Only the milling head spindle moves up ang down
Miliing head was setted to 55 degress angle
And performed drillng /oversized the hole
Threading with 1/2 UNF tap
Inserted with threaded 1/2 UNF stud bolt
And drill with required tap drill size for making the original tapped hole
Просмотров: 117
Видео
How to make lathe machine tailstock leadscrew nut
Просмотров 2913 года назад
The lathe machine tailstock leadscrew was worned out /lost square thread lead screw has 8TPI (eight threads per inch) Foremerly the leadscrew nut has only designed 2 locking set screw. A newly made has designed 4 locking allen cap screws with in the flanges 4 each 1/4 Nc cap screws
Blow out preventer Bolt,Re-threading
Просмотров 383 года назад
BOP (blow out preventer ) 4-1/2 Diameter bonnet bolt the thread is bit swollen may be due to some foriegn object inside and right heavily. so ,re -thread on the4 jaw lathe then pass through with the threading Die to assure the original thread spec's
How to machine eye bolt without using 4 jaw chuck
Просмотров 853 года назад
The eye bolt has bigger thread diameter So it's not able to used safely using lifting Due to few thread's only way in the flange t9 lift This vedio shows a new Idea how to machine eye bolt on 3 jaw chuck using special centering jigs/attachments To applied re threading operations
Wash pipe wear flange
Просмотров 243 года назад
This part was used in wash pipe assembly unit ,that face was worned out. So need to build/filled up with the stick welding. And machined at 3 Jaw lathe machine
How to machine victaulic pipe
Просмотров 2,2 тыс.3 года назад
machining a victaulic pipe 5-1/2 OD pipe 12 inches length 5/16 wide groove 1/8 depth groove
Fabrication of air regulator bracket
Просмотров 293 года назад
New bracket was made and machined/ to fit on the regulator flanges Operations involved such as: Lay out and Drilling hole's Counter sunking to attain bolts lengths to tight properly on flange /diaphragm
Crain swivel pin fabrication
Просмотров 313 года назад
new crain swivel fabrication 2 inches diameter fabricate pad eye for lifting. welded on the top to lock and un-ock (welding process not shown on the video due to rush..turned over to the welder and i stalled by the mechanic)
How to make pipe nipples
Просмотров 10 тыс.3 года назад
Machining, making,fabrication of pipe nipples 3 inches diameter pipe ,threaded both sides 8 thread's per inch 6 inches long and 12 inches long
Coupling , boring and keyway making
Просмотров 1,3 тыс.3 года назад
machining coupling 1 inch bore 11/4 key way
How to cut heavy wall seamless pipe
Просмотров 393 года назад
A heavy wall seamless pipe need to be cut /separated for a purpose/ material for spare parts using center square to locate the center line clamp on the milling vice and drilled thoroughly until completely drilled both wall side Separated by using hacksaw
bolt / cutting and re-threading
Просмотров 233 года назад
bolts are long.. need desired length do center drilling and threading longer than the original thread lenght cut and facing
How to make Spacer
Просмотров 783 года назад
fabrication of 4140 grade spacer from a piece of mechanical pipe clamped on chuck lathe and drilled series of drill bits from small to big size Do boring operations. repeatedly to reach the required bore diameter, turning outside diameter cutting off , facing and champering
How to Fabricate a stud bolt
Просмотров 1873 года назад
Fabrication of stud bolts from old bigger pins rough cutting simultaneously on my 3 lathe machines 2 lathe machines has equipped with automatic feed stop mechanism so it helps to produced rough cut round bar finished product.. 1inch diameter round bar, Threaded with 8 TPI ( thread per inch) x 3 - 3/4 Thread length all nuts and washers are OEM (originale quipment manufactured)
Equalizer pin repair
Просмотров 713 года назад
Truck suspension Parts equalizer pin worned out. welded /build up then machining into proper /original size @70mm Diameter
Fabrication of milling machine table stopper
Просмотров 1203 года назад
Fabrication of milling machine table stopper
Fabrication of cassette type torque wrench, Ratchet Pawl
Просмотров 363 года назад
Fabrication of cassette type torque wrench, Ratchet Pawl
How to service and repair Chain blocks
Просмотров 1,3 тыс.3 года назад
How to service and repair Chain blocks
Paano tanggalin ang naputol na pipe or fittings
Просмотров 1,5 тыс.3 года назад
Paano tanggalin ang naputol na pipe or fittings
How to convert universal unions to fire hose adapters
Просмотров 643 года назад
How to convert universal unions to fire hose adapters
How to repair / re-machined worned out high pressure fitting
Просмотров 673 года назад
How to repair / re-machined worned out high pressure fitting
2-Way's how to extract broken Npt pipe threads
Просмотров 1,1 тыс.3 года назад
2-Way's how to extract broken Npt pipe threads
How to drill multiple hole's, on a multiple plates
Просмотров 1573 года назад
How to drill multiple hole's, on a multiple plates
How to make 5/16 hex key socket screw driver
Просмотров 2443 года назад
How to make 5/16 hex key socket screw driver
Good idea but the video is looks like its taken during a earthquake…
stop the music
Is there an automatic machine for making iron gate hinges? Please talk to me, my dear friend.
Hello, thanks for your information but kindly show how to mount the work piece on lathe machine using lathe dog
What lubricant do you recommend?
@@euanconnelly8122 we used mechanical grease yellow color
1:27 "Paparallel"?
Did you lubricate the friction discs? 🤔
It is BSP or NPT
ang galing nyo naman po boss
Great
Sir apka aders orno deto
Way too slow
It's a manual machining
Hello
Thanks for your comments but for me it's Easy to tighten and to lossen God bless you
That chuck with the centre drill has been seriously abused. It must have been used by an absolute moron to get in that state. And what is that giant locknut on the other chuck, presumably to stop the thing slackening off????
Sir g ma ya Kam krt ho
sir are u using a cnc machine to cut the threads can it be done with rolled sheets or pipe only plz help
I am using manual lathe machine and I do it threading manually; And the material are seamless pipes
Horrible music
Boss paano ako maka bilinian ng bhusing mo
boss pwede ba gawing shock spacer ng sasakyan ang ganyang material?
Ppwde rin
@@BenjieTebs ano po ba pangalan ng material na yan sir?
How much did you remove and how long did that take? Asking because I need to machine down a 5 1/2” impeller to 3 3/4” for a 2hp grinder pump
Nice 1 bro
Parang cnc milling din, ganyan gngwa ko nung nsa HItachi taiwan ako and sa dito sa local PMC
Manual machining bro. sa vedio naging cnc moves hahaha
Nice video. God bless you and your family. #Godfirst01
Why you didn't tapered it?
My machine did not have a taper attachment
Good
Is it possible to cut tapered NPT threads to straight threads? I'm working with 2.5" NPT.
Yes. You can make it unless the diameter of your straight thread is smaller than the diame of straight thread
Hi where you from
Nice love from sri lanka ❤️
very nice, but, what happen when some client ask you for 500 nipples? xD
ЛАЙК однозначно ЛАЙК!!!👍💯👈
Thanks for your such appreciation God bless you
Eto pala ang ginagawa mo kuya,☺️
Yes po as a machinist Lahat ng repairs Fabrication or paggwa ng pyesa At design or modificstions, Remedies minsan matagal ang OEM( Original equipment material) orders
Nice keep it up po , take care and god bless po sir
Welcome po and I'm happy to hear your good complimentary
😲😲galing👏👏👏
Oh salamat po sa compliments
Galing ng tuturial bro maganda nga ganyan ng sasalita ka,goos job
Shukran..
Cgi po basta papanoorin nyo hehe
Very nice tutorial sir tnx for sharing your video God bless and stay safe always sir I'm watching from port of Panama idol 👍👍👍👍👍
Welcome po and .thank you po sa pag tangkilik be safe din po always
No probs sir 👍👍👍👍👍
Good job bro
Bro mega Love SHOUT OUT
Bro mega Love SHOUT OUT
Bro kumusta dika na naka vedio bz ba bro ingat lagi Po sa trabaho
Oo busy sa work at mainit dito Tsaka mga gwa ko same din sa mga nagawan ko na ng vedio
Soon more videos to come with voice over hehehe
Can I ask you about the type of the plastic that you used sir
We called it engineering plastic
KatroPa kumusta ingat sa pag gawa
ang galing naman
ang ganda pag may mga gamit din na ganyan..hehehe
👍👍👍
Galing mo tlga bro gumawa
Katropa ingat sapag maniho ng makina pero galing mo
Watching here idol warly tomas
Good job sayo bro
Hi Friend how are you so noce music
Im fine...thank you