- Видео 6
- Просмотров 34 325
Trick-tech
Добавлен 19 янв 2021
This channel will makes tech easy for you to elevate you your mind with what you could be done with technology and every thing its made from the same main thing that's surround us in every place we go or where we go its Electronics which every tech made of . here i will show you tricks and schematics and microchip programming and how could you make any project you want i hope i for you all to get out from my channel with some info that could help you in life or at less makes live easy for you
إنها تسهل عليك التكنولوجيا لترفع عقلك بما يمكنك القيام به باستخدام التكنولوجيا وكل شيء مصنوع من نفس الشيء الرئيسي الذي يبدو لنا في كل مكان نذهب إليه أو حيث نذهب إلى الإلكترونيات التي صنعت منها كل تقنية. هنا سأعرض لك الحيل والخطط وبرمجة الرقائق الدقيقة وكيف يمكنك إنشاء أي مشروع تريده ، وآمل أن تخرجوا جميعًا من قناتي ببعض المعلومات التي يمكن أن تساعدك في الحياة أو على الأقل تسهل عليك
إنها تسهل عليك التكنولوجيا لترفع عقلك بما يمكنك القيام به باستخدام التكنولوجيا وكل شيء مصنوع من نفس الشيء الرئيسي الذي يبدو لنا في كل مكان نذهب إليه أو حيث نذهب إلى الإلكترونيات التي صنعت منها كل تقنية. هنا سأعرض لك الحيل والخطط وبرمجة الرقائق الدقيقة وكيف يمكنك إنشاء أي مشروع تريده ، وآمل أن تخرجوا جميعًا من قناتي ببعض المعلومات التي يمكن أن تساعدك في الحياة أو على الأقل تسهل عليك
How to Burn bootloader on new atmega328 using Arduino UNO
Here in this video i will show you How to burn bootloader to the new Atmega328 using Arduino Uno to be ready for easy programing for new projects or to replace the original Atmega328 chip on the Arduino Uno
---------------------------
you will need
1-Arduino Uno
2-breadboard
3-jumper wires
4- Resistor 10K ohm
5-crystal 16Mhz
6- two of 22pf capacitors
And finally any Atmega328 without bootloader
-----------------------------------------------
you will also need the
Arduino IDE
-------------------you could Download it from the link--------------------
www.arduino.cc/en/software
--------------------
If you like Please Support me with like and SUBSCRIBE and share
Hit the bell to get the notifications as...
---------------------------
you will need
1-Arduino Uno
2-breadboard
3-jumper wires
4- Resistor 10K ohm
5-crystal 16Mhz
6- two of 22pf capacitors
And finally any Atmega328 without bootloader
-----------------------------------------------
you will also need the
Arduino IDE
-------------------you could Download it from the link--------------------
www.arduino.cc/en/software
--------------------
If you like Please Support me with like and SUBSCRIBE and share
Hit the bell to get the notifications as...
Просмотров: 1 200
Видео
DIY Digital Tone Control Rocking Sound TDA7313 controlled by arduino
Просмотров 21 тыс.3 года назад
#Arduino #ٍSound system #Amplifiers #TDA #sound processor #Electronics #diy #homemade #Howto #Audio IN this tutorial video i will show you On the TDA7313 audio processor using Arduino, you can make a simple but functional tone and volume control. The TDA7313 microcircuit has three stereo inputs, bass and treble tone controls, loudness and four outputs (pseudo-quadro). The control is carried out...
How to make a Soldering Station DIY كيفيه صنع مكواه لحام ستيشن احترافى ديجتال
Просмотров 4,7 тыс.3 года назад
#Soldering #Homemade #How to make #Diy #Arduino صناعه مكواه لحام ستيشن احترافى مبنى على Atmega328 و به مزايا متعددة -قياس درجه حراره سن المكواه -التحكم فى درجه الحراره من زرار واحد روتارى -boost mode بضغطه قصيره على الروتارى سويتش -ضغطه طويله على الروتارى سويتش للدخول لقائمة الإعدادات -حساس حركه دراع المكواه عن طريق (ball swich) -الكشف عن المكواه الغير المتصل (عن طريق تحديد قراءات درجة الحرارة ...
How to make oca lcd bubble removal controller شرح طريقة صناعة كنترول ازاله الفقاعات
Просмотров 6 тыс.3 года назад
#How To Make Automatic Oca bubble Removal Machine #Homemade #How to make #oca #Arduino. My other project is How to make a Soldering Station DIY كيفيه صنع مكواه لحام ستيشن احترافى ديجتال 👉👉 ruclips.net/video/yQ_QE0j6xsY/видео.html
فية تليفون للتواصل
يمكن التواصل على الواتس 01227127669
hallo sir I have Kinley followed your work its impressive ,my question is i have tda7433 will it work in this project thanks bro
Thank you sir and yes tda7433 could be used as the same but with different code and schematic I could provide you with it if you want
ola ,voce tem algum projeto de um pre amplificador que usam 2 potenciometro e no display mostra o VU meter em barra no fim do display mostra os dbs canal A e canal B tudo isso em stereo
اذا اردت تبديل لوحة اونو بلوحة نانو في هذه التجربة ما هي الخيارات في البرنامج التي سأختارها ؟
فيديوهات كتير شاهدتها بتشرح نفس الكلام ولكن للأسف لم تفلح معي أي منهم ، أما هذا الفيديو فهو الوحيد في توصيل المعلومة ببساطة ودقة ودون تفرعات وتضيع وقت ، ونجح معي من أول تجربة ، تسلم وبارك الله فيك .
شكرا اخى الله يباركلك و يصلح مابين ايديك و لو احتجت اى شى انا تحت امرك
boarddefs this lib is not connecting
Dear, please advise me.
Hi dear all, I have facing some problem with this project like: first when I upload the same code, I didn't get any message on to the LCD, only light up. I have already solve this problem to write lcd(0x27,16,2); instead of lcd(0x3f,16,2) but now I have got another problem " menu changing its self continuously and not working. Can anyone help me please, also inform me about encoder connection detail. Thanks
Hi dear all, I have facing some problem with this project like: first when I upload the same code, I didn't get any message on to the LCD, only light up. I have already solve this problem to write lcd(0x27,16,2); instead of lcd(0x3f,16,2) but now I have got another problem " menu changing its self continuously and not working. Can anyone help me please, also inform me about encoder connection detail. Thanks
ini jga bagus ruclips.net/video/XTGUwuxoZdA/видео.html
Hello friend, a favor, help me to program my arduino, it does not recognize the library or it tells me an error, how could I do it? Could you give me your watsap? I pay your work
No problem sir my WhatsApp # is 01227127669 I think you need to put 0012 on the beginning
Hello friend, please help me program my arduino, it does not recognize the library or it tells me an error, how can I do it?)))))))
Hola amigo la verda no puedo instalar ami arduino la libreria como puedo hacer ? Me ayudas le pago $$ amigo dame tu watsap
Can give me only pin connection 👍 i will make a schematic for you and u can post it on drive it will be helpful for me too .. thx for replying
Sir all the pins in and out are on the code but tell me what the problem and I will help you out
@@Tricktech1 thx
You are welcome sir did you got everything working
Hello everyone, I would like to inform you that finally I have build the code but now I have got another problem "I can't understand the schematics" can anyone give me the whole schematic. Thanks
Sir the pins in the code and let me know if you still need any help
Can any one inform me that showing an error "Error compiling for board Arduino Uno." many ways I try to solve but I cant
please اخی I'm waiting for answer.شکرا
hello my friend .can you please give my the diagram of soldering handle wire ?like how did you wire ball switch and temp sensor to main borad?
شغل ممتاز وكود متقدم جدا جدا لى طلب ... نبدأ من البسيط الى المركبب يا ريت فيديو عملى لتوصيل طرفى حساس الحرارة والدائرة الخاصة بالحساس فقط بناء على قراءة الحساس والنجاح فيها ... ممكن تكملة المشروع حتى ولو محدود الامكانيات انا حاولت ابدأ بالحساس لكن للاسف فشلت ... مافيش اى قراءة المرة الوحيدة اللى تمت القراءة بشكل جيد لما وصلت الافوميتر مباشر لطرفى الحساس وجدت المقاومة ترتفع عند توصيل 12 فولت على طرفى السخان خلاف كده ما عرفتش انفذ الجزء الخاص بمضخم الاشارة فى دائرة ابسط من دى ================== يا ريت شرح كيفية تنفيذ ادخال طرفى حساس الحرارة وقياستها كيفية توصيله للاردوينو شكرا جزيلا لحضرك تحياتى
شكرا لزوق حضرتك باذن الله حعمل لايف فيه شرح بالتفصيل الممل عشان فيه ناس كتيره واقفه فى حته قراءه الحساس و مكبر الاشاره حضرتك ممكن ايضا استعمال max6675 to r للقراءه من التيرموكوبلر بس غالى عشان كده بنستخدم مكبر اشاره lm358 حضرتك فعل الجرس و باذن الله الايف حيكون قريب و ممكن حضرتك تتواصل مع واتس لو احتجت اى مساعده 01227127669
@@Tricktech1 ارسلت لحضرتك على الواتس سؤال بخصوص موديول max6675 اللى هاوصله للموديول طرفين حساس الكاوية ولا هاستخدم السلك اللى مع الموديول والصق طرفه لمعدنى مع الكاوية شكرا جزيلا لحضرتك
تكلف كام دلوقت يا هندسه
تواصل معى على الواتس ٠١٢٢٧١٢٧٦٦٩
ممكن اعرف حساس الحركه متوصل ازاي في قلب المكوه
دى كاويه هوت اير
@mohamed_essa2010 كاويه 907 وممكن تشتغل على t12 ايضا
What hating element did you use in the video? is it A1321 or A1322 and thermostat sensor or thermocouple sensor
Both are thermocouple for 907 Hakko and if you needed any help let me know sir
Wich one pin of 7313 if im using as subwoofer output (mono)? Tx mr
Sir Tda 7313 got 4 output which you could use 2 of them for l and r and used the other two with subwoofer 4558 preamp for mono sub I have my set like that
@@Tricktech1i see that, put the 2 output to the subwoofer module as mono n controll manualy right?
Which pins are for Rotary encoder and IR receiver?
Remote is not working could you please suggest which Remote is compatible for this project.
Sir you could use any remote with this project you just need to read the remote single in hex the put them in the project on the remote section
Sir check the pins in the sketch
Sir i have uploaded the same sketch as you shared with link and the issue I am facing is when I press any key of old apple tv remote the volume Information comes on i2c and nothing is happening, no volume increase decrease no input change. Please suggest what mistake I did in this process
Hi, I am resently join with you I am really surprised to watching this project, but i have got aproblem to built it with sketch, its showing an error like "Error compiling for board Arduino Uno." can any one help me please.
Do you have the included libraries installed
@@Tricktech1 I have tried to include libraries as sketche then include libraries. But I am not sure if it is installed or not. If I made it wrong, would you please show me the way to install the library?
No sir you need to install the library’s in document/arduino /library
@@Tricktech1 Thanks a lot with respect
No problem you more then welcome
ماشاء الله الله ينور على حضرتك فضلا تليفون أو طريقة للتواصل واتس او ماسنجر
واتس 01227127669
Hello sir. Thanks for the code. I am little confuse about connections. Can you give me full schemitic diagram
you must try tda 7719/ tda 7419
I would love to bro specially pt2323 for 5.1 but I don’t have it in my country but I will keep looking thank you though for bringing it up and by the way I got the codes for them and the libraries
hola me gustaría hacer este proyecto , pero requiero ayuda, como programar paso a paso el Arduino uno
Sure thing sir I will be glade to help you could hit me up on WhatsApp and I will be posting shorts soon for every little thing
oP!
Yup
amigo buenas noches me puedes ayudar a hacer con el arduino leonardo y pt2313
Sure thing my friend gime your email and I will send you the files for pt2313
Sir, please help me out? I am getting an error like this C:\Users\xxxxx\OneDrive\Documents\Arduino\libraries\TDA7313-master/TDA7313.h:8:10: fatal error: vector: No such file or directory #include <vector> ^~~~~~~~ compilation terminated. exit status 1 Error compiling for board Arduino Nano.
Sir install the Tda library including in he description folder
Bhiya number do
لو سمحت انا عندي مكواة لحام بس انا بستخدمها فحجات فنية زي حرق على الجلد و كده المهم هل ينفع اركبلها زي مقاومه او زي مفتاح النور البكرة اللي بيتحكم في الاضاءة عشان اقدر اتحكم فدرجة حرارتها ولا ده يبوظها؟
Hello brother. I'd like to ask, can I use TDA8425 instead of TDA7313 by just replacing to TDA8425.h?
Thank you for asking bro no it can’t cause it will need to be changed cause tda8425 got only 2 output but if you need full sketch made for Tda8425 I will be happy to help 🥳🥳
Hi, I successfully coded arduino uno. But i can't make the Lcd to work. I made the SCA and SDL connection from lcd to A4 and A5 to arduino uno. But still nothing on screen can you help me?
Disconnect the Tda from the circuit and see if the lcd working after you upload the code and pay attention to the pins in the code cause I had changed the pins in the code but not in the schematic try and let me know if you need any help I would be happy 😊
انا عاوز اعمل مكبس لشغل صيانع محمول ممكن تساعدني ياهندسه
طبعا من تفضل كلمنى خاص و انا تحت امرك 😊
@@Tricktech1 تسلم جدا على ذوق حضرتك العالي
ببعت لحضرتك عالواتس
TDA7313.h:No such file or directory Arduino code error bro
Add the library included in files and if you need help feel free to hit me up 🤙
@@Tricktech1 bro library file direct link please send
All files included in the description you will find the library folder copy them all to your Arduino library folder it will include the Tda7313 library
@@Tricktech1 ok problem solve bro❤️
Can this project use lcd keypad shield?
Thank you for asking sir and yes you could use it but you need to change the lcd library from I2c to normal lcd and point out the pins you need to use and please feel free any time to ask if you stuck at something
👍
sorry sir... when pins 27 and 28 are connected to a4 and a5... the program immediately stops. (hank) what caused it to be like that?? and if i replace tda7313 with pt2313 does the coding have to be adjusted again....?? Thank You.
🙏
Is it possible to add "Middle" controller with TDA 7313?
No the tda7313 doesn’t have mid range
@@Tricktech1 Okay, i'm looking for 3 band tone control. Thanks for sharing anyway.
There are Tda with 3 bands like tda7718
@@Tricktech1 Can you share the schematic diagram and Library compilation for such control using TDA7718?
Yes sir if you have the Tda ic and you need the code and schematic please contact me on WhatsApp my # +201227127669
Bisakah saya mendownload foldernya secara langsung?
Yea you could sir all the files included in the description 🤩🤩if you need help let me know
ملفات المشروع كتير ممكن الملف المستخدم في الفيديو هشغلها علي نفس نوع الكاويه اللي ف الفيديو
رفعت ملفات المشروع فى ملف مضغوط اسمه hakko 907 ولو احتجت اى مساعده تحت امرك 🤩👍👍
@@Tricktech1 شكرا هجرب واقولك النتيجه
لو احتجت اى مساعده قولى 🤩
yalla yalla
My brother
I have this amplifier I want volume, power on, if possible Pause, nest and previous displayed on lcd.....pls can u help me....thanks...I can drop few dollars....pls the money is not to get u to doing it....it's just to show seriousness on my part...thanks....reply and I shall send my mail do we can communicate in real time
Thank you for asking sir you could tell me what you need to do and I will be super happy to help you
@@Tricktech1 I need a custom display console for Amplifier....I'm working on a rechargeable home theater speakers
Hit me up on what’s app +201227127669
@@Tricktech1 ok
Hello brother, where we can buy the tda7313? Can you share link for the store.. thank you
Hello bro thank you for asking but i buy them from my local electronic shop I haven’t try to buy it online but I guess you could find it on AliExpress just give it a try 👍👍
@@Tricktech1 ok thanks, ali express i.c. most of them are fake, it won't work...by the way where you from?
I didn’t know that and i grew and raised in the us but iam from Egypt 🇪🇬
hello, I did not understand the connections between the tda7313 and the display, in the video you say pin 1 and 2 but reading the datasheet would be cref and vdd. Thanks for the reply
Thank you for asking to make it clear the lcd is connected with I2c and the Tda also connected with I2c both they connected to the arduino i2c a4 and a5 and the I2c pins on the Tda 27 and 28 i hope you got what you was asking for and if you have any question please feel free to ask any time 😊👍👍
@@Tricktech1 thank you very much for your reply, you have clarified my doubt
How to program adrino
You got all files you need in the description 🤩🤩
can it work for arduino nano?
Yes it will work also work on nano sir 🤩