Видео

Very good drone video please add me

Looks like ancient ruins. Very good!

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

1

3

2

1

Super cool vid

The video is still really good. Consider next time doing some software stabilization after recording the video.

is this belt different from the serpentine belt? or does our accord only have one belt? I have 2009 v6 coupe manual. car is 200,000km and i have not had anything done on it before except for oil changes and tranny fluid change

Thank you soooooo much. That job took me like 30 minutes and that included the time to get my tools and put them away. 19mm on my Harbor Freight breaker bar and I was DONE.

Thank you... please tell me what milleage and years you need change this timing belt... ???

Hi next time you heat the crankshaft bolt up.

Thank you!! I kept thinking my tensioner hydro strut failed / seized (204,000 miles) ended up being the fact that I didn't hold constant / slow pressure to let it contract. Sheared the adjustment point off both ends and had to get a new one. This info wasn't listed anywhere I looked. Much appreciated!

can you please advice me ? my car done the 200,000 KM / the engine voice became noisy & indicates that something is wronge shall I send it for a mechanic or ignore it COZ some mechanics told me to ignore it please advice boss ???

Thankyou for posting this...Taking the power steering pump off helped me to replace my knock sensor wire that a mouse chewed up in our 2010 honda accord exl v6..

what about cam, crank seals + waterpump?

Holy Moly was this important info for me. I've worked on cars for over 50 years, less in the past decade or so with the greatly improved reliability of the cars I have bought. But I haven't seen anything like this with the exception of a Harley Davidson hydraulic chain tensioner for the cam drive. If it had been a weekday I would have already called a service center to have it done I was so pissed. I am replacing the power steering pump and couldn't even loosen the belt. Thank you so much. The rest of the job was a breeze. What might be common knowledge to some might be a nightmare for others. I'll share one little tip for removing the P/S pump. You'll notice on the 08' and 09' V6 that the lower pump bolt is really a pain to get to. Removing the pulley will help but it hits the motor mount before coming off it's spline. Remove the rear/upper mount bolt *ONLY* and you can scoot the pulley off revealing the lower bolt. Thanks again.

Thanks for posting this!

Is it necessary to replace a tensioner if it's dirty and the drive belt is cracked?please let me know, I'm looking to do these repairs before the warranty is up on my contract.

You should of gone to www.rockauto.com and bought a timing belt component kit with the water pump. You would of saved a lot of money.

Another thank you from Dallas, Tx.

Thanks for sharing this because this is my next project. I do Honda maintenance videos as well on my channel. I have over 20 videos of scheduled and basic maintenance on my 2008 Accord EX-V6 sedan. I do warn you though, I grew up in a blue collar family, and have spent the last 11 years of my life working with the Navy...both being enlisted and working as a civilian contractor so there is cursing and swearing in the videos. So if you do watch, please don't be offended. I'm trying to keep the cursing and swearing at work and off the camera. Thanks for sharing this

Thanks for sharing this.

Dude!!! There are not enough videos about the 2008/09 accord V6 hydraulic tensioner! Thank you!!

You saved my butt. my daughter was heading back to university, I was checking her 2010 Honda accord V6 over I noticed her serpentine belt was half gone, I keep a spare belt but no garages open to change it. I know about tensioners but was not aware of the hydraulic type on this car. when I got the socket on the tensioner I was expecting it to move instantly like most, it did not, so I thought it was ceased until I watched your video. had it changed in 10 minutes. just wanted to thank you for taking the time and putting the video on.

if my my tensioner piece is stripped. is there any other method of releasing the tension?

sir you save me so much time, i did the same thing you did, I tried everything until i saw your video. keep up the good work