- Видео 163
- Просмотров 43 212
OpenLearning Channel - Sumithra
Индия
Добавлен 28 мар 2020
Hi friends,
In this channel, u can learn new software's how to use them and tool used in it.
designing of complex geometries, analysis of the models, and some new techniques .
For more interesting videos, subscribe to my channel.
In this channel, u can learn new software's how to use them and tool used in it.
designing of complex geometries, analysis of the models, and some new techniques .
For more interesting videos, subscribe to my channel.
Видео
V- Fitting - Isometric Figure
Просмотров 92День назад
Hi, Today will discuss about the Fitting trade - V- Fitting Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
L Fitting - Isometric Figure
Просмотров 80День назад
Hi, Today will discuss about the Fitting trade - L-Fitting Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
Rectangular Scoop - Isometric drawing
Просмотров 126День назад
Hi, Today will discuss about the TInsmithy trade - Rectangular scoop Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
Rectangular tray - Isometric figure
Просмотров 114День назад
Hi, Today will discuss about the Tinsmithy trade - Rectangular Tray Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
Half Lap Joint - Isometric Figure Part-2
Просмотров 102День назад
Hi, Today will discuss about the Carpentry trade -Half lap joint (Figure-2) Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
Half Lap Joint - Isometric Figure Part-1
Просмотров 135День назад
Hi, Today will discuss about the Carpentry trade -Half lap joint (Figure-1) Isometric drawing from Engineering Workshop. Thank you Subscribe for more videos
Corner Lap Joint Isometric Figure Part-2
Просмотров 156День назад
HI friends, Today will discuss about the Carpentry trade corner lap joint (Figure-2) from Engineering Workshop. Thank you Subscribe for more videos
Corner Lap Joint- Isometric Figure Part-1
Просмотров 228День назад
HI friends, Today will discuss about the Isometric drawing of carpentry trade exp-1 corner lap joint part-2 from Engineering Workshop. Thank you Subscribe for more videos
Some Important Abbreviations
Просмотров 44Год назад
Hi friends, In this you can learn some important abbreviations. For more videos, subscribe to my channel
Convert perspective to isometric in CATIA
Просмотров 107Год назад
Convert perspective to isometric in CATIA
How many constrain has in this sketch?
It works tysm bro
Thank you, it was very helpful.
i need report on this can i get
How to smooth visualisation of fonts in DRAWing-module in Catia v5?
Mam, when we applying force at different point location, firstly cleared old data and show the result again. if need to clarify that whether the result same after clearing data also
Results will be same if load is applied at same point, if you made any changes in input conditions (material, load position) results are different.
that's what i am asking case 1 load at one point (sum of three) & case 2 load at deferent location whether the result will be deferent ??? @@openlearningchannel-sumith5439
Is this 3D Or 2D
Mam your videos are really good for CATIA beginners. Thanks alot MAM
Thanks for this video......i was searching how to create coordinates in CATIA 🥰🥰
when i insert symmetry region and then then try to acces details of symmtry. nothing shows off
Can I get your contact
Can i get the softcopy of this ..!? Urgent
Om Namah Shivaaya
thank you mam
Thank u for the video..keep posting...all the best
Thank you, I will
Tqqq so much mam
Great one mam thank u
Greetings, I have followed the steps you applied. but the selected pdf has shown black page, not showing the line drawings. why is so? what is to be set to resolve the issue. than you.
why is the selected pdf showing a black page? the pdf figure will not be shown. thank for your response.
the file is open.
Thanks ma'am 🤗
🔥🔥
When i am select a plane in design moduler in ansys work bench, that geometry is missing what to do madam
check whether ur sketch is in hide option , if its hide right click on sketch to show
@@openlearningchannel-sumith5439 imported model is missing madam. I didn't see that import model.
After importing the model, click on F5 functional key to generate..so that u can see the model..
The geometry is appearing after generation, i have to select the face so i am select a plane after select a plane that import geometry is missing this is problem madam
@@vimaltadepalli320 can u send me ur model to my mail id once sumithraguni10@gmail.com
thank you so much mam
Most welcome 😊
Nyc explanation mam
thank you
Perfect learning point
Wow nice buddy 😀
tqq dear...😊
I want drawing could you give me pdf
ruclips.net/video/SPfxitzt7vU/видео.html Sketch to pdf
Thanks madam
Thank you so much, you saved me a ton of frustration!
Superbb explaination .....
Thanks a lot 😊
Nice
thank you ...
😁
What is the pad length of radius 35 and 18
Tq...for.slow n neat initiation
Keep watching
A good initiative to learn like this...