- Видео 6
- Просмотров 396 312
Green Baler Parts
США
Добавлен 29 июл 2016
Watch our channel for Tech Tips from Green Baler Parts. Our technicians have repaired, reconditioned and dismantled hundreds of John Deere square balers, and their experience has enabled us to learn what kind of baler problems are caused by worn parts, faulty adjustments and difficult conditions. This has also lead to innovative re-designs of OEM parts to create better baler performance and longer life for your equipment. Our custom manufactured updated Slip Clutch Center and Tucker Finger Kit represent significant improvements to original equipment for Series 6, 7, 8 and models 14, 24 and 224 John Deere Square Balers. All our used equipment goes through a rigorous checklist before it gets labeled "Technician-Certified, Field Ready", so you can save a barnful of money, and buy with confidence. Visit us at www.greenbalerparts.com
How to remove knotters from a John Deere 336, 346, 327, 337, 347 Square Baler (with captions )
We've had many requests over the years on how to remove knotters from the 6 and 7 series John Deere balers. It is a project that always requires patience. If your baler has been left outside or not cleaned regularly, the parts may have rust and grime that will make removing them harder. This video includes some tips that will help you overcome some of these issues.
This video is a step-by-step guide that sets the correct sequence to make removal a more simple process. Once you're done removing your knotters, pack them up and send them to us to rebuild them! We rebuild over 300 knotters a year, so we'll take care of them and send them back to you as good as new...maybe better!
This video is a step-by-step guide that sets the correct sequence to make removal a more simple process. Once you're done removing your knotters, pack them up and send them to us to rebuild them! We rebuild over 300 knotters a year, so we'll take care of them and send them back to you as good as new...maybe better!
Просмотров: 80 923
Видео
Improve Your John Deere Baler With Our Updated Tucker Finger Kit
Просмотров 27 тыс.4 года назад
A sloppy tucker finger assembly will make baling a hit-and-miss proposition. This updated kit will eliminate the wobble immediately, and keep it tight for many bales to come!
Eliminate Wobble With This Improved Slip Clutch Center
Просмотров 32 тыс.4 года назад
This updated Slip Clutch Center eliminates the need for the OEM spacer on the drive shaft splines. Extra thick center results in full engagement with splines, reducing wear and eliminating wobble.
Shim Your Knotters Correctly for Best Performance
Просмотров 89 тыс.4 года назад
Here's some things to look for when you're shimming your knotter.
Adjust Hay Needles To Tucker Finger Update Kit for John Deere Square Baler
Просмотров 100 тыс.4 года назад
Improve your bale-tying process with our Updated Tucker Finger Kit. Updated Tucker Rods make this unit tight and accurate.
Save Time and Money- Rebuild Your John Deere Knotters
Просмотров 67 тыс.4 года назад
The heart of the John Deere Square Baler is the knotter. But worn parts can mess up your bale ties. Green Baler Parts can rebuild your knotters- just replacing the parts you need- for less than half the cost of a new knotter.
Where is the guide that is to the right That the Tucker finger presses the string against Is it needed with the upgrade
❤❤
Thanks for sharing , greate help 😃
Are there any videos on wire tie balers. All I can see are about twine tie
Would there need to be any re-timing done after replacing the assembly?
Are there any videos for wire tie balers
I have a wire tie baler. Do you know parts for it
❤❤
Bravo colleagues, cool job 👏
Nice. Good to know.
I bought new knotter ( Rasspes 3663) and put it on the svaft...but but the new gears ( 2 small pinions were not samekind like in shaftgears, old one )so when I used the machinery manually it didn't work , starved and I had to take loss the parts from shaft...I put the old one back and try to make hay this year..and maybe use old gears ( pinions ) for my new knotter...when I have more time . I have Rivierre Casalis Er 40 ex baler
What is the cost of the modified slip clutch for the 24t?
مرحبا
Toop
Tension
Are you designing knot system.
I have a jd 336 baler. There are two holes at the top of each needle. Which hole does should the twine come through (top or bottom)?
top
Number
le falta el buge
I'm saudi It worked please visa me
How can I contact you and what is your phone number
👍
How to synchronize it or put it on time friend?
How to synchronize it or put it on time friend?
Я хочу, будь ласка, пояснити молодшому 349 металевий дріт
Где можно заказать
Hello! Tell me where you can buy a knitting machine?
Simply stated this is one of the best videos I've ever seen for equipment repair on anything I have looked up. Keep up the great work and thank you for putting this video together.
I just exploded my knotter frame on my 336 so I really appreciate this video!
Tank's
number whatssap please
God why wasn't it like that from the factory
Do you have a drawing of the part? Dimensions?
I have a john deere 346 wire the left side does not tie every 15 loose bales 2 or 3
Why? Does it give me more thread on one side, like an inch or two more?
Why? Does it give me more thread on one side, like an inch or two more?
Where are you located?
Wie stelle ich sicher, dass die Saiten nicht von Nagetieren geschnitten werden? Danke
Some twine comes with rodent repellent
Wie stelle ich sicher, dass die Saiten nicht von Nagetieren geschnitten werden? Danke
Wie stelle ich sicher, dass die Saiten nicht von Nagetieren geschnitten werden? Danke
the needles on my 337 baler seem to be about a foot too long. i just bought this baler
Can you guys put phone number please thank you
Excellent, because my friends just snapped the beak off, which looks to be because it has more like 50 though of gap. And we have no book on setting it up. Fingers crossed the shaft comes out okay.
Sme z Slovenska. Kúpili sme balikovač Johann Deere. Máme veľký problém. Není tu servis na našom trhu. Náhradné diely sú strašné drahé. Mám hlavu v smútku.
En español
Traducción en español
Traduccion en español x favor
Could you guys make a video showing how to time the plunger to knotter on a 24T?
Ok servis jundiyer