Видео

Hope everyone is getting excited for the 2025 season! Let's do this, y'all!

It's been a dream of mine to dig a really deep hole. What man does not want that?

Where is you top plant

Only thing I do differently is in sequencing your steps - I make the actual bar length sizing cut first (instead of dealing with double length material and splitting it later), then the two dato blade end cuts BEFORE the thinning cuts on the planer. That way my "center" for the material thickness is consistent for both end cuts (fence distance to center of dato is constant) and only the dato thickness changes end for end. - then I run the material to the Planner to narrow the sidebar thickness on the bottom - then final step is to slice it into sidebars. Just feel like that is more efficient and easier to do measurements and adjustments on the saws. I don't use a dato blade on the table saw for my end cuts (I don't like placing material vertical on the saw) - I use a 7/8" (top bar groove) and 5/8" (bottom bar groove) router bits on a router table and since both have the same fence setting to center them I can run all of my material on a top end pass, then switch router bits and run the other end - all I need do is swap the bit and set the depth of the cut. Then last step of course to slice the material into sidebars. Good video though - your tool safety is well thought out and very repeatable.

Exceptional video. Thank you. Does the Diameter of the mesh matters for the bees?

We had the same problem. This year was strange. No honey produced in our 10 hives. The weather made it very hard here in Eastern Idaho.

Machine a wedge to go behind your fixed jaw to change your nip angle Also IMHO your bolt on toggle mount is weak and probably flexing. a shim adjustment against a welded in piece would be more rigid. Still one of the better diy builds I've seen

Finally somebody being nice and not just trying to make a buck off of newbees.

Easy pezzee lemon squezzee! Thank you for sharing this.

good review. looks like a nice unit.

friends, make damn sure you wear hearing and eye protection when using an angle grinder, and ventilation when welding.

Hello Welcome Good morning Sir you re a very Good and great very nice you machine Crusher

Hello Welcome Good morning Sir you re a very Good and great very nice you machine Crusher

Great content! Looking forward to seeing your progress!

"Elelater go down the hoooole"

This is by far the best nico tutorial I have seen yet. Thanks.

Great video! Thanks, for showing every step only once, instead of showing 4 x the same! It makes looking this a joy! Well done!

Good job making box joint supers and deeps. These will last 20 years and more. Pre-drill all nail holes, use water proof glue if you have it. It will seal the wood from moisture. A simple jig like this is all that is needed and keeping focused as to what you are doing so you don't cut the wrong part. Thanks

Oh man I cant wait to see more of this in the future thanks for sharing!

Угол упорной пластины ,скорее всего, не тот,нужно точку опоры смещать выше прижимной пружины.

I would combine any of the weaker ones that you don't think will make it and feed, feed, feed. Invest in some hive alive fondant patties or similar.

Thank you for sharing your process. Very streamlined.

Can you share the link of these things, because me to i want to buy

Thank you

I loved watching this cut out. It's annoying when you go to watch a cut out video and they don't show you the actual cut out. They just shoe you the start and then the empty cavity and then the relocation. Sometimes people click on a thumb nail that says cut out because, strangely enough, they want to see the cut out. Thanks for showing the actual cut out, although not in entirety. May I suggest you fil more of the up close camera footage? Or film all the footage up close? The up close camera footage is amazing because we can actually see the bee behaviour and their colony, brood, honey ...everything. That's what is so interesting, the bees and what they have created!

too bad the "save" button is disabled, I would love to save it so I could come back and re-watch this great tutorial

simple and best

Outstanding work sir. Thanks for sharing.

Excellent video. So helpful. Thanks for all your time and work to create it.

Good video. I'm about to start with the nicot system.

Great series, you do a really good job explaining it all and making it clear- If you were going to build it again would you change anything?

Very helpful - thank you for posting this!

I build them somewhat the same. But no special top cut. 3/4 all cuts. And do the top corners opposite of how you set it up. So no adjusting my dado.

My man! These videos have been extremely helpful. Thank you for making them!

That's too cool 😊

Happy for you! Still waiting for the first swarm here. Unusual for me not to have caught any swarms this late in the season. Are your bees ahead of schedule or on time for swarming?

If the end boards that have the frame ledge had the pocket instead of the pin at the top you wouldn't need to make any adjustments. It would just be a full depth normal stepover cut. Correct?

Loving this amazing playlist! thank you very much, I wonder how did you just put the nuc frames immediately into the hive like wouldn't there be a fight?

Hi I have used the nicot system for years and had good results, but to get top results when you inspect your hives weekly save the Royal jelly from Queen cups in a small pot so when you have positioned your queen cups in your cassette using a cotton bud dip it in the Royal jelly and from the front of the cassette holes push the cotton bud covered in Royal jelly in to the cell touching the cup bottom and turn to add the queen jelly substance and odor into the cell bottom, this will increase your queen cell take by 50% more. Regards Paul.

Thanks for sharing! Nice job.

Thank you so much, perfect man. L o l❤

Great video and just what I needed. Thank you!

Good Stuff! Well done!

With the box on the floor and the handles up to the sides mark the angle on the bottom of the 2×4's and counter sink the nuts,wouldn't that help with the hight problem picking up the box? I'm going to try your idea by copying wheelbarrow handles and a hinge. Thanks for sharing ✌️

Do you need to wire the plastic foundation?

You should got up close to show more. Good video tho.

You are awsome! I am so very tired of using my router to make my boxes. Thank you for showing me how to make a proper bee box!!!

Very nice but why you don’t use the board to all four sides to band the sheet?

Planning on using this in the future

That works. You have given me all the info I need to repair or build a new cover. Thank you for the BOM and detail construction.