Видео

I don't think your screwdriver is long enough, lol.

You must be a trump voter.

Your pump is recalled fyi. Contact bestway

The toilet spacer is supposed to be even with the floor then you add the flange which should be above the floor.

it’s a little extreme to say you got ‘scammed’…there was no exchange of money, no contracts signed. The guy most likely got tied up with whatever job he was working that day. He basically offered you free wood and delivery, payment being the convenience for him not to transport it further. Plus, whatever $ to take down that tree/trees. You and your son did more than your due diligence in getting the site ready, which is more than any customer would normally do. But just because the guy was a no show that day should not count as you getting scammed.

I do chimneys for a living. The top one isn't supposed to be mortared in place incase it gets damaged. Makes it far easier to replace.

How does the gps work

You would need the trap and vent to be in the same location as the new washer and dryer, you cant run a long pipe to it.

Great video!

We make stainless steel chimneys, if you want we can sell it to you

Not sure if the power wires you ran are heat resistant, THHN has a temperature rating of up to 90º F; the primary job of an electrician is to be a fire control technician; a Nichrome or Silicone wire should be used.

Where did you get that flashlight! I am blinded watching it siting on my couch. Lol

Hanging out with ordinary folks doing things ordinary folks do.

So this type you don’t need the 4x4 posts installed inside of them then.

You need to measure the cylinders to see if they are in specs and straight and round top to bottom.

The biggest problem and defect is the operator

😮😮😮

Kevin, Looks like I'll Be comment # 1 for your Video on "Generator interlock and inlet box install". I do appreciate your no nonsense, matter of fact way you demonstrated installing the interlock system and associated generator startup procedure. Tomorrow, as of this writing, I will be installing a generator kit. Trying to wrap my head around basically lining up to drill the holes, you helped alot in that. I appreciate the time you took in this video. Thank you.

Great insights

Looking at 20:08 you can see how the freewheel rod is bent. My mower is 6 years old and the freewheel rod got so bent, I couldn't get it back into gear. I have the plastic General transmission. I bought a carburetor throttle swivel and a 1/4" metal rod, removed the flimsy rod, heated a 1/4" bolt with a propane torch, and enlarged the hole that the rod was in. I bolted the swivel on to the plastic trans tab (use the nylon lock nut & washer), cut, bent & threaded the rod. Now I have a very stiff rod that will not bend. To make this upgrade, just remove the left rear wheel, and it is easily accessible. 1 - 36" rod will make 2 disconnect rods, each 18" with a 4" handle(14" + 4"). Thread the handle into the swivel, then use the supplied nut to jamb and lock it into place. I moved the location the rod comes out the back, to the corner hole to the left of the keyhole shape. Poulan Pro pp19a42 - 19hp Briggs motor with General Transmission. Parts; JEGS Carburetor Linkage Swivel | Fits 1/4" - 28 Right Hand Thread Throttle Linkage Rod | 1/4" - 28 RH Male x 1/4" - 28 Female | Includes 1 Washer And 2 Nuts National Hardware N316-372 4054BC Smooth Rod in Plain Steel,1/4" x 36" uxcell 1pcs Round Die Stock Handle Wrench Holder & 2pcs Round Die 1/4-28 UNF Machine Thread Right Hand

Giddy up.. 🐎🛞😅. Great video.. 👍🏻

I have the Husqvarna ST 138 2015 model and it drives fine in reverse, but when I push the foot petal to go forward it starts driving in reverse as well.. Can not work it out for the life of me..?

What are you using to clean your block and heads?

He prob went into the box knowing u we’re reaching in it constantly an wanted some more attention ❤

He's on break! Leave him be, by law you cannot interrupt it

The squint eyes letting you know he loves you❤

😂❤

Reminda me of my old cat i miss him😢

Aww

I wish I wasn't allergic to cats.

Give that apprentice a raise ❤

Tiger is so cute 🥰

We will see. I had the same problem. It was deflating. I figured it was the last year for the spa. I asked my son to fill it up with air in the middle of the week. He forgot. The way to the water, pulls it away from the Pump and it has cracked the water outflow where the hose is attached inside the tub so I think I can fix it but I’m gonna see what you found.

I would bore the cylinders, change the piston and connecting rods, those don't look right, and clean the crankshaft and the in side of the engine thoroughly and over haul it.

bro idfc about the rings i ned to know which way to put the pistons in smfh

Good job Kevin and Dawson 👍🏻

How long will that wood last

New sub, adorable cat ❤ I agree about more trains, less trucks

DAYUM! I love a good stack of wood😂 termite haven!

It looks good Kevin

Thank you for doing this video, my mother thinks one died in her dryer and it smells when she turns the dryer on. Funny thing is her dryer is new and this never happened before. Could it be the way the dryer was installed?

Nice job Kevin 👍🏻

Awesome job Kevin 👍🏻

How has it held up?

It looks good Dawson and you and your dad did great job on it 👍🏻

Nice deck but you need to complete the video and show how you insttalled the railings you got lazy

Awesome video! Love abandoned rail lines. Got to like the male Karen’s calling out trespassing while they praise hobo shoestring for illegally riding trains and breaking into locomotives. Anyway, thanks for sharing.

Seems Ryobi doesn't put any lube in the reciprocating assembly...the the HP version is a total pain to get in there if you want to lube it yourself. Planned obsolescence?

Get the GoPro goin

I wish y'all were in my neck of the woods. I have a project in mind that I'll definitely need help with. (Alabama).