Видео

thanks homie

Fck ur annoying subscription

Great video! Very helpful, thanks!

Great video thank you. My 2017 with 220k KM started to make bearing noise....going to be way easier than my old VW...

Link for front brakes www.amazon.com/gp/product/B0CGTFH5FQ/?tag=steevegmtec03-20 Brake cleaner amzn.to/47a1DS2 Brake grease amzn.to/4686u4X Wire brush amzn.to/47bcbAC Basic hand tool set amzn.to/45NgS2e Hammer amzn.to/49y3dyU Pick set amzn.to/45JVyKR C clamp used amzn.to/3SIogc0 T30 www.amazon.com/dp/B07R7DFYCS/?tag=steevegmtec03-20

Why does the harness on the website look different from your video?

Thank you for the help.

Graciassssss

What is the part number

I’m about to attempt this myself. But I have no idea how much fluid to let out. I don’t want to drain all of the coolant.

Thank you! This video was easy to follow and straight to the point.

I wish I watched this before attempting to replace my wheel hub. Just ordered a replacement hub because I messed up the thread trying to free the axle from the hub (the punch did not work). The cv axle is seized up in the hub. I think I'm going to have to take the entire cv axle, hub, and knuckle out as one. Any advice when I try to free the axle from the transmission? I see you used a prybar, but I don't want to damage the seal. Also, how hard should I push before hearing the "click" when installing the cv axle? Thanks

Great Video Thanks. Also, if doing a brake job, does it make sense to change the brake fluid? To avoid calipers jaming later on?

Don’t you have to do the screws in order and 71lb

I have a 21’ v8 5.3L Silverado Im getting this jerking or skipping feeling from my truck when I accelerate, i have no lights on my dashboard so i have really no clue what it could be (i have 90k miles). But anyways i started looking around for solutions to this “skipping”, ive found a list of things to change and im starting off with my spark plugs, i just wanted to ask you if there are any sensors i should watch out for? For example when i changed out my brake pads i accidentally damaged a sensor and then my truck was limited to 40mph.

What will happen if I leave it out because I hate the auto stop

Links to where u bought the wires ?

Is this the same process for 2018 GMC TERRAIN SLE?

What software is that?

This guy pulls these parts like butter and I was shaking the f out of them. Would of broke things if I wasn't patient

What are the lug size

Did you buy the kit or just replace pads. I wonder if you can reuse the sensor?

If you replaced the brake pads after receiving the "Service Brake Pad Monitor" message on DIC, you'll need to erase the fault codes in the EBCM before resetting the pad life. I was able to erase these using my local Autozone's scan tool at no charge. My fault code for rear brakes was C116B "Rear Brake Pad Wear Signal Circuit - Not Plausible".

Thank you your instructions were perfect👍💯

What did you say? Not flush ignition coil?

Sadly, I never thought of putting the rotor on temporarily to clean it--much better than trying to do it off the car.

My guy, how did you get that 18 mm caliper bracket bolt off? The bottom one. I cannot for the life of me get the damn thing off.

i have this issue, take it to the dealer?

Hi just a front alignment or all 4

Torque on cover?

How long should the disassemble and reassemble take in total

This was the only thing that worked for me ! Thanks !

you don’t even show how to replace it ? that’s a waste of video

I changed mines and now the reduced engine mode comes on when I start my truck but with the broken one it wasn’t coming on right away 🤔🤔

Nonsense.. you cut how difficult it was to remove e the pump .

Im working on a 2020 Chevy Blazer. Do i need a scan tool for the front brakes?

Can you make a water pump tutorial for this type of truck?

I think I'll just stick to wiggling the shift knob every time i get that message xD

Good joob

I have a P0089 an P228D p0013 for a 2012 Buick regal 2.4l any tips?

So far not working on a 2020 Equinox. The light comes on but does not flash.

It’s happening to me Suburban 2024 I don’t find the conector in the driver seats any help please

Finally a how to video where you get right to the point! Thank you for your help! It worked!

Nice edit ❤🔥🔥

Link for scantool www.amazon.com/gp/product/B0C3GJTD45/?tag=steevegmtec03-20 Link for the rear brakes www.amazon.com/gp/product/B084DVDTM3/?tag=steevegmtec03-20 Brake cleaner amzn.to/47a1DS2 Brake grease amzn.to/4686u4X Wire brush amzn.to/47bcbAC Basic hand tool set amzn.to/45NgS2e Hammer amzn.to/49y3dyU Pick set amzn.to/45JVyKR C clamp used amzn.to/3SIogc0

you scratched it all up. get some plastic trim tools and save your interior. nice video though

Those handbrake shoes where done as well

Thanks for the video straight to the point and saved me about 50 bucks! 🫡

You are amazing sir thank you god bless 👍🏽🙏🏽💯

Do you need to add any oil to the system?