Видео

U cemu je problem

What was it?

U can also you brake cleaner.. it works very fast and it will evaporate just as fast

mine doesnt sound like this. only the last part where its idling so i might have the same problem in the future

110 volts or 220

Coolant maintenance issues

Hello sir how much it will cost to rebuild this engine issue? I got same issue ford focus diesel engine

Was it driving fine?

How does one fix this issue??

That disc dont look much better than the one you took of , why use scrap metall ??

Thank you for the video, I have changed them myself now. If anyone wonders about torques, for tensioner bolt it's 8Nm plus additional 270 degrees. For fuel line bolts it's 28Nm. If you have air in fuel system, try to prime it by pressing the on button and then off after 4 seconds without the clutch depressed around 7 times and then start the engine. For me the engine started around after 8 seconds 👍

How are you brother? Does it work on Siemens and Piezo injectors?

Times the waterpump too nice

Solution?

Hello, I have gas in the air conditioner but it doesn't give cold, what could be the problem?😢

What happened

Is it easy to remove those last 3 wires if i want to take out the fush box to replace it?

Thanks for the video . I have a couple questions 1. Do i need a torque wrench when tightening the stud back into place? and 2. Can i just use a regular ratchet? The tool you used seemed pretty heavy duty.

it is the relay from the passenger compartment fan?

it's about the passenger compartment fan not working for me

Slapping noise bore change round to oval shape slightly that noise coolant maintenance over heating issue

Perfect video. Thank you, EXACTLY what I needed to know

Mine is doing the same happy days lol

Hello! I think that i have same problem as this ford. Was there lose of power when this noise appears?

Useless video

Was the car using much oil? Have the same problem with a vrs

MAF sensor as featured in this vid is usually very close to the air filter and I use spray brake cleaner to clean. The MAP sensor is commonly fitted to the inlet manifold airway and can be successfully cleaned with oven cleaner. Hope that helps because after that you're looking at removing the EGR and /or manifold and clearing all the soot out.

Excellent video, thank you.

"promosm"

is it worth rebuilding the engine with the parts and time or would you rather got a new car? i have the same issue i’m pretty sure

so why was the sensor worn out on the end? was the bearing damaged ?

Truly appreciate your step by step video. Your tutorial is spot on. You saved me a lot of $$, also gave me the confidence to take the job on. Thank you friend!

Golf 6 1.6 TDI I have the same problem, I changed the injectors with new ones and seals but fuel doesn't come out from the lines of the injectors. Do you have any idea what it could be? The seals are new

👍

How did you know this was the problem ?

What was the problem

Now it's a tractor.

Bdfhfhfh

Hi my fan runs continuously even after I’ve switch my engine off I’ve got Peugeot 3008 Please help

Rod knock , bearings from the rod. Comon problem on gtd

Thanks

Would this be the same for 2005 plate?

This is the hight presure pump i belive

Hello, have you fixed a problem and how? Thanks

Iniettori da sostituire

Mia ford focus 1.6 tdci 109 cv 427.000 km mai mai un problema mai....!! Motore eccezionale...!!

I did this and now my car won't start. I tink all injectors are stuck... I just replace the rubber part, put it back and bam, not working

I just got a ford 17plate with 49k miles the same noise is coming and the low engine light is one. Does that need a mechanic or putting the oil would fix it ?

Definitely needed a new disc

So what was the problem with this one in the end??