Видео

แนวนอนครับ

หน้าจะมีตัวไดตัวหนึ่งเสียหละครับแบบนั้นครับ

an esc for DC motors 'brusched esc' in theory should emit an output signal composed of a wave, more or less square, at a fixed frequency with modulation of the duty cycle proportional to the ppm in output from the channel of the RC receiver. I say in theory because in some ESCs, in the outputs towards the moTors there are filtering capacitors and also recirculating diodes inside the Mosfets themselves that could alter the pure signal, so in the end, instead of many square waves, a single modulated wave would be obtained. only on the wave crests, therefore an almost continuous signal and therefore fixed or slightly variable speed on the motors. the best and rather easy solution to implement is to use a microcontroller like Arduino which also has libraries ready for the BTS7960 modules, to convert the ppm RC receiver signal into PWM and DIR + Enable to better control the power module and take advantage of the variable speed

/* ARDUINO 1 Board No 1 for right motor IBT-2 pin 1 (RPWM) to Arduino pin 5(PWM) IBT-2 pin 2 (LPWM) to Arduino pin 6(PWM) IBT-2 pins 3 (R_EN), 4 (L_EN), 7 (VCC) to Arduino 5V pin IBT-2 pin 8 (GND) to Arduino GND IBT-2 pins 5 (R_IS) and 6 (L_IS) not connected ARDUINO 1 Board No 2 for left motor IBT-2 pin 1 (RPWM) to Arduino pin 8(PWM) IBT-2 pin 2 (LPWM) to Arduino pin 9(PWM) IBT-2 pins 3 (R_EN), 4 (L_EN), 7 (VCC) to Arduino 5V pin IBT-2 pin 8 (GND) to Arduino GND IBT-2 pins 5 (R_IS) and 6 (L_IS) not connected */ int RPWM1_Output = 5; // Arduino PWM output pin 5; connect to IBT-2 pin 1 (RPWM) MOTOR1 int LPWM1_Output = 6; // Arduino PWM output pin 6; connect to IBT-2 pin 2 (LPWM) MOTOR1 int RPWM2_Output = 8; // Arduino PWM output pin 8; connect to IBT-2 pin 1 (RPWM) MOTOR2 int LPWM2_Output = 9; // Arduino PWM output pin 9; connect to IBT-2 pin 2 (LPWM) MOTOR2 int motorSpeedA = 0; void setup() { pinMode(A0,INPUT) ; // connected to CH2 forward and reverse pinMode(A1,INPUT); // connected to CH1 turn Left and right Serial.begin(9600); pinMode(RPWM1_Output, OUTPUT); // Rigth side pinMode(LPWM1_Output, OUTPUT); pinMode(RPWM2_Output, OUTPUT); // Left side pinMode(LPWM2_Output, OUTPUT); } void loop() { int rcValue1 = pulseIn(A0 , HIGH); int rcValue2 = pulseIn(A1 , HIGH); if (rcValue1 >= 1500 and rcValue1 < 1900) // Reverse { motorSpeedA = map(rcValue1 , 1500, 1900, 1 , 255); analogWrite(RPWM1_Output, motorSpeedA); // POSITIVO MOTORE COLLEGATO ALLA USCITA MOTORE POSITIVO DEL DRIVER analogWrite(LPWM1_Output, 0); analogWrite(RPWM2_Output, 0); // POSITIVO MOTORE COLLEGATO ALLA USCITA MOTORE POSITIVO DEL DRIVER analogWrite(LPWM2_Output, motorSpeedA); } else if (rcValue1 >=1000 and rcValue1 <= 1430) // Forward { motorSpeedA = map(rcValue1 , 1430, 1000, 1, 255); analogWrite(RPWM1_Output, 0); analogWrite(LPWM1_Output, motorSpeedA); analogWrite(RPWM2_Output, motorSpeedA); analogWrite(LPWM2_Output, 0); } else if (rcValue2 >= 1000 and rcValue2 <= 1430) // Turn Left { motorSpeedA = map(rcValue2 , 1430, 1000, 1,255); analogWrite(LPWM1_Output, motorSpeedA); analogWrite(RPWM1_Output, 0); analogWrite(LPWM2_Output, motorSpeedA); analogWrite(RPWM2_Output, 0); } else if (rcValue2 >= 1500 and rcValue2 <= 2000) // Turn Right { motorSpeedA = map(rcValue2 , 1500, 2000, 1, 255); analogWrite(LPWM1_Output, 0); analogWrite(RPWM1_Output, motorSpeedA); analogWrite(LPWM2_Output, 0); analogWrite(RPWM2_Output, motorSpeedA); } else // STOP { analogWrite(LPWM1_Output, 0); analogWrite(RPWM1_Output, 0); analogWrite(LPWM2_Output, 0); analogWrite(RPWM2_Output, 0); } Serial.println(rcValue1); Serial.println(rcValue2); }

I think it is using an besc for DC motors 'brushed esc' costing a few dollars on aliexpress, the output of the BESC instead of directly driving a small motor drives the inputs of the bts7960, obviously it feeds the BESC with no more than 5 volts for not damage the inputs of the bts7960. in principle it works fine as a system but it would be better to use a microcontroller like arduino to create the interface :)

@@salvatorebarbaro5862 thanks

@@salvatorebarbaro5862 how can I operate 48V 1200watt motor wirelessly , plz guide.

@@pushpakdeshmukh9106 you intend brushed motor or brushless ? 48V - 1200W are 25 Amp, for brushed motors : some H Bridges can handle 25 Amp 50 volts, a lot depends on whether you then have to control them via an RC remote control, in this case there are 2 alternatives, an H bridge that accepts the PPM signal of an RC receiver as input, or an arduino that converts the PPM signal of the receiver into PWM signal to drive the H Bridge . A little more difficult to manage a controller for Brushless motors at 48V , which hardly have an input for PPM RC signals, often only have a 0-5V input which comes from the throttle knob. in that case, always with an arduino-type microcontroller, the PPM signal must be converted into a 0-5 Volt signal and applied to the input of the BR controller instead of the knob

ESC for pwm signal.

ได้ครับ แต่ต้องใช้วงจรนี้2ตัว

@@doit-aimlessly พอจะขอวงจรได้เปล่าครับ สนใจทำรถบังคับเล่นครับ ขอบคุณครับ

ฟอรจูน ทำได้แล้ว ขอบคุณ .เจ้าของคลิป