Видео

What where the symptoms of faults the car haves?

I was changing my spark plugs cause of rough idle. At the end doing some cleaning I accidentally found it was completely snapped off

Thank you for the good instruction.

Best method/video is this one on this problem IMO. The technique allowed me to refit the sensor within 15 minutes. This worked on my 1er E87 diesel, just careful the sensor is elsewhere, located on the right side below the brake fluid container. After changing the sensor, the error dissapeared, no need to clean the codes.

How did u get the second screwdriver in such a tight space to push the sensor back into the servo ?😮

Were you getting eml light for this

1900% !

You're welcome!

Mine was really really badly corroded rather than spending the time fixing a new one is only £15 on eBay

Thanks! Replaced mine exactly like here. However it doesn’t have it’s 180degree range anymore even though its smooth and so on. Its only about 130-140 deg maximum.. weird!

Superb video, thank you

sorry any suggestions if the pivot and wiper central part stucked together? thanks

Noticed mine wasnt going all the way over and all the way back, i used silicone lube spray and it doesnt work at all now😂😂

Take the sticker off.

I like the way you highlighted fuse))) Thanks for the video!

thank you

guess what I know what I'm doing tomorrow... cheers

Spent 4 very frustrating hrs trying (unsuccessfullly) refit this sensor yesterday. Watched your video this morning and had it done in 15 mins! Thanks so much for posting this video 👍

What did you do to fix your mirror back on ?

I didn't even have to disassemble, I just sprayed wd40 on the pin, pressed it in and out, cleaned it and now it is working again! It doesn't spray wiper fluid though...

mine just goes in and doesnt come out,like it doesnt have a spring,what should i do??

Thank's !! i was thinking by all system but after i saw your video i fixed it. :)

Thank you!

Hi good video and did it sort the code out ?

Who do you recommend to fix the frm.

I’ve got the same problem but it isn’t coming so easily.

so did it work, when you installed oem bmw sensor?

Great video, best (easiest to follow and do) description I've seen yet! Thanks.

Hi. Would you please tell me what is your engine N47 2L diesel? As I have BMW 320d M Sport N47 engine and can't find the right map sensor. The Ebay send me wrong one but they said its suitable for my car! My map sensor looks similar to yours as the size is slightly bigger than Ebay send me ! Big thanks if you give me some information!🤔😉👍

Thank you! You have just made my life so much easier! 👍🏻😎

I had the same problem, I send the module to Grosvenor Motor Company in Reading, post code RG1 8EQ

problem in ABS sensor on one of your wheels.

Nice video. Did you manage to get a refund for your dodgy sensor? My start/stop warning light comes on intermittently but even when it’s not on my auto start/stop doesn’t work. Was yours like this?

Would you (or anyone else) know of how to test these sensors - e.g., should they have a specific resistance between the pins?

On left side way is impossible to take the sensor out

Nice editing on the hard bits pushing in the gromit lol, thanks for the video very helpful

Hello, If your BMW has an AGM battery, then select the car & AGM symbols (middle two LEDS) using the red Mode button. This limits voltage to around 14.2 - 14.4 Volts, the recommended voltage to charge an AGM type battery AFAIK. It's best to avoid using the RECON (fourth LED) charge setting with an AGM but its fine for an FLA battery as this applies 15.5 Volts for an equalising charge. An AGM battery would gas excessively and pop out the pressure relief caps which results in your AGM battery drying out.

Did you clear the codes when you fitted the new sensor

did this fix your problem?

I had this issue on the 1 series. Buying the genuine part from BMW was the only way I was able to fix the issue

Hiya, I have managed to get mine out but I'm struggling put the new one in

How did JB ClearWeld 50112 hold up?

Does brake fluid leak when the sensor is removed or is there nothing behind it that can leak? Do you have to adjust anything on the brake system afterwards?

Hey. I have same problem.. but i'm opening the trunk and lights does't work.. if I'm opening rear window ( from button) lights work... Did you know how to solve this problem?

gsf and eurocar do it at half that price

The bottom part that the crankcase hose goes into, what is that called? Mine is kinda broke and doesn’t connect to it properly

This is exactly what i needed! thank you!

I have the same issue and was think how to get thing back in, so thanks for the tips but I also just brought a cheap one off Ebay claiming to be new but definitely isn't. Don't even use startstop just want to get rid of the annoying bong lol. 115 quid is a lot for something you don't use.

Only 20£ ?