Видео

The usual nice neat work. My only suggestion is to upgrade your recording equipment. A little too much distortion

It’s not a V6, just saying…..

What brand and size are those rims? That's exactly what I'm looking for.

these have some back fire from stock once you remove mufflers

That's perfect. I've had the 40 series, outlaw as well. I'm going to go this route, with the resonator. I guess I'm getting older...lol. Thanks for sharing, I "liked"

I like that.

The Frontiers Red and Blue are awesome!

Is that 2 y pipes 😂😂😂😂

Very well done work sir.

What kinda mufflers you got there?

Super 44 or 40? You said 44 in the video but your title says super 40? Please let me know i am after this sound!!!! 😮

The rear of the car doesn't look stock, but I like it.

Which super 44 was this one I seen like 4 different part numbers

Glad to see you back. Beautifully done, and sounds great!

🔥🔥

Would doing this affect any of the sensors in the truck? And also would this void the warranty of the truck?

This sounds amazing , would you happen to know the part number?

Yeah I need to do this to my pro 4x

Why didn’t you put the y pipe where the heat shield splits ??

Sounds great and I can't believe you're in Jax! If I get a mustang I'll be swinging by. I'm new to mustangs but have always used the flow master 40 on different vehicles. I know there are a lot of mustang exhaust options but some of them sound too raspy or too loud in general. This one sounds pretty good. What does removing the resonator do?

My car is a 2018 civic coupe and it’s stock rn but if I did a resenator delete and got a 2.25” mgma flow muffler would it sound around the same?

way overdone

This is a first. I have never seen the 2nd Exhaust Outlet from the Mufflers connected in the manner. Interesting set-up.

What specific Magnapack was used? Did you guys replace resinator with the Magnapack?

Sounds great, very nice tone. 🤘

WOW!!!

Sounds great

The rear brake ilght panel is not 77.

Will you lose horse power if you just delete the resonators? They are located where you swapped out those Super 44s

Anyone ever figure out what motor this is? I have a 3.6 but don't want it sounding like rice like in most of the videos. Edit: This is more than likely the V8. 3.6 would be AWD and have an AWD badge on the trunk. I could also be wrong tho. I'm from way up north, so basically all the 3.6 here is AWD.

will these fit a 2022 model?

And my doors are hard to close in the winter

Do you have the 36 gallon tank? I do and I I'll run outta fuel when the gauge reads 1/4 tank. I know it's empty bc I'm getting over 600 miles a tank

Got to lose the resignator. I took mine off and sounds way better and probably twice as loud

Part number please

U have part number

Sounds awesome

Can I get the pipes to come straight out the back of 2018 Tahoe or do they have to go to the side like in this video ? CHARITYBOWL85

I want side pipes on my 68 so bad.

thanks for your information

I think you might want to upgrade your camera or microphone. I don’t think it’s capturing the sound as good as it can. The work looks very clean though.

The problem is that no matter what year or model of a Corvette you buy; one accident and it is totaled. They are all plastic. Hello!!!

Sounds great you wouldn't think it's a 4 pot

X pipe isn’t factory

its sound awesome in that 6Cyl

Hi magnaflow but what series?

Your welds look very clean from the few videos I have seen so far. Nice work. Sounds great

Can you do dual tips with the factory valance?

I wouldn’t mess with a 4-cylinder car. It’s a joke to try make it sound like a V8. Leave it stock boys

What’s the part #