Видео

Im sorry, my inverter model is different from yours. I dont know how to correct the fault. Plese read the manual that came with the inveter.

Disable the alarn. If we have the same model, it is parameter setting # 25,

Ayos naman. Wala namang problema.

​@@MrOwenyeynaranasan mo na sir ang fault 26?

Nasa 3k yata yan bossing, di ko na matandaan. Ginamit ko sya minsan ng 15mins di naman nag lowbat.

Anong "sos"? Baka OSO yun

Negative boss, masyado na malaki wattage ng pv. Ang max nya ay 1,600 lang. Dapat yung voc nya di lalampas ng 100

Tansya ko bossing nasa 2kilos.

@@MrOwenyey salamat sir.

@@MrOwenyey another question, ilang hours bago mafull ung battery & paano mlalaman full na?

Kapag nag green yung led ng charger, full charge na yan. Depende sa state of charge ng baterya yung pag charge, mas matagal nagamit yung baterya mas matagal i charge.

ruclips.net/video/5uX4qFb2xMI/видео.htmlsi=EW4zqqLf1C8S93DQ Watch mo yan bossing, parameter settings ko.

@MrOwenyey salamat po sir

Naka power saving mode yung inverter pero yung mppt nya umaandar.

On testing yan, kung gumagana ang automatic transfer to du kapag umabot ng low voltage na setting ko.

50amp, 40amp dati kaso umiinit masyado kaya nagpalit ako ng 50

Pacensya na boss, nawala sa isip ko. Di ko na matandaan ngayon kung ano ang link.

Hindi pa naman. Naka set kase itong sakin na mag transfer sa meralco kapag na reach nya yung 24.8v ng baterya.

@@MrOwenyey ah un sken po kc hindi ko nilagyan ng ac input..

same issue sakin ngayon

7 days lang warranty boss sa shoppee. Pero mahigit 1year na sya, maayos pa rin.

There are 2 kinds of inverter, one is 220/240v output and the other is 110/120v output. Each of them also has two different hertz output. Either 50hz or 60hz. Check your your inverter if it is compatible with the requirements of your appliance. Hope this helps.

@@MrOwenyey Thanks Sir your response in time the specs is Ac output 230Vac 50/60hz but currently is on 50Hz I tried all I can so solve the issue , Because the inverter is not connected to AC/DC at the moment I hooked it with one my battery to test the inverter while I'm still waiting for solar panels that I have ordered but I think it must work even though the the inverter is not currently connected to anything but 12v only?

@@MkatekoChestar set it to 60hz. That should work just fine.

@@MrOwenyey thanks Sir I will adjust it

Yes, sa kanya.

@@MrOwenyey hm kuha mo ilan ah yan?

@@reyreyes621975 17k 100ah

@@MrOwenyey boss makunat pa rin ba battery mo nganyon?

@@MoleraTagupa makunat naman, basta na charge ng maayos.

Maayos naman. Naghaharvest kahit makulimlim.

@@MrOwenyey malakas din ba magharvest gaya ng srne na mppt controller?

@@kasanaall9848 malakas kung sa malakas, depende yan sa solar panel kung magandang klase.

@@MrOwenyey ibigkong sabhn po is meron naba kayong experience ng comparison ng harvest nya?

​@@kasanaall9848ang gamit ko dati walong bosca 160w. Mahina ang output nya

Ok boss, gumagana pa naman.

Maayos pa rin. Mga 2,500 to 3,000 bawas sa meralco kada buwan.

@@MrOwenyey as a whole setup or sa srne lng?

Sa lahat na. Sa 3kw mga 2 to 2.5k. Sa 1kw 4 to 6 hun.

Pwede, basta cguraduhin mo na hindi ka didikit sa kung ano man ang winewelding mo at dapat naka leather gloves ka. Safety first parati.

Series yung 2 tapos parallel.

Solid yung copper nya boss.

@@MrOwenyey buti po yan solid..yung nabili ko may halo na tube na maliit

@@cellibra3117 saan gawa yan?

@@MrOwenyey nabili lng boss online.

Baka china clone yan. O baka ganyan na talaga ngayon.

4x 405w jingko bifacial mono, 25.6 v 100ah

Kelangan ng baterya para gumana.

2350W I believe

Kung di ako nagkakamali nasa 6k bossing.

Di ko maalala eksaktong presyo, pero nasa 1k yata.

@@MrOwenyey saan po kau bumili

Ngaun pa lang po kc ko gagamit mg welding machine DIY lang po

@@MarkSantos-u5n sa lazada. Hanapin mo yung ingco official store.

@@MarkSantos-u5n ayos yan, ingat lang. Malayo sa mga madaling masunog. Safety first.

Apat na jinko 405w yun akin bossing. 48.45voc at 40.19 ang vmp. 1,600w ang max pv wattage. Pwede sumobra ng konti.

Ok naman. Sa halos 1 yr na gamit ko sya, walang aberya.

Yes, basta malakas si haring araw, ayos.

@@MrOwenyey ano batt naka kabit sa snre mo?

24v 120ah Pina assemble ko.

Anong fuse? Yung mga circuit breaker ba?

1,620w bossing Apat na 405w

Gumagana pa rin boss. Almost 3 yrs na, maayos pa naman.

Mas recommend ko yung mas mataas na wattage boss, para di masyado hirap ang jigsaw sa pagputol.

@@MrOwenyey ginagamit ko lng ng marine plywood numero 1 ok lang ba?

@@angelogantalao5050 mahina pag 1 lang, sa 4 o 5 para mas mabilis makaputol.

Importante rin dyan yung klase ng blade na gagamitin.

@@MrOwenyey hindi paps yung uno na plywood lang.. hindi yung variable speed..

Eto mas maingay boss.

@@MrOwenyey thanks for the reply, yan sana bibilhin ko, buti nlng at na mention mo na medyu maingay kaya naghanap ako ng ibang brand na less noise

Parameter # 8 is battery type. Ask your battery supplier how many string does your battery pack have. Parameter # 9 is boost charge voltage. Do not exceed the recomended charging of your battery pack.

Maayos pa naman, wag lang isabak sa mabigat na gawain. Di sya heavy duty. Pang DIY lang sa bahay.

@@MrOwenyey .. ok sir salamat.. ..

@@MrOwenyey NASA 2 years na Po Pala Yan tools mo Po.? Working pa rin Po ?

Yes, working pa lahat. Pang gamit sa bahay lang naman kase, pang diy ko lang.

Yes, it does.

Mine too. I was operating a Nespresso Machine with tv and lights. Thank you for answering.

@@AnonymousAnonymous-tt8irhow’s the inverter working out? Is your espresso machine more than 3000-6000w?

I honestly dont know how cells are arranged in a battery pack. Better ask the seller where you got your battery. Thats what i did.

Thank you for this video. It helped me very much. I followed your instructions. I got the inverter yesterday.

I have'nt encountered code 21 yet, but have you replaced the fan with the same specs? If yes, maybe it's the fan temperature sensor that is broken, i suggest to bring the unit to technician for proper diagnosis.

@@MrOwenyey actually we fixed the original fan ourselves. (Some wire needed to be soldered, but i noticed there’s a lil motherboard inside of it…) .And then it was spinning okay after plugging it back on the inverter motherboard . But the fault code was still there. But after watching a video in there with a guy encountering the same problem, i’m thinking about buying a new one.

​@@buisserethpatrice87 hey could you direct me to the video that you found in having the same issue now..please

@@roneilsmith3637 It's the same video you're commenting under now. My experience with the 2 exhaust fans on the bottom was that they were not receiving the proper signal from the board so they could start spinning, and if they don't spin , the code will show up on the screen and the inverter automatically stop working. Basically how it works is, when the inverter motherboard reaches a certain temperature or overloads, the fans (3 of them) must cool it down. On each fan, there are three wires, one is +, the other a -, and the other one is the sensor, which communicates with the motherboard. My suggestion is to check if they are all connected inside the fan. Even if they are, you might need to replace the fans because they probably gave up.... or the one that's failing because the inverter won't work with only one, and the code will show up no matter what unless both fans work normally.