Видео

Excellent job

Thank you❤

What model is your diagnostic tool?

Did you replace your chain guides? all the chain slack causes misfires

Can I use warning emulator ? Cheap and fast fix ?

Thanks you so mach

nice thanks for sharing, i have similar code but my problem was the battery was completely dead i kept driving with jump pack starter until one day gear box stoped engaging. i changed battery - the problem went away!

Thank you 👍

Thank You ! You saved my day .

That’s the same as mine though just looking at your video exactly same looks exactly like the sane

thanks for this!!!!!!

Ty so much for your reply I will keep trying to break it loose use so wd40 or some other penetrating spray

I took the bolt off pulled on it and everything it isn’t coming off I was just wondering how you got it off

Hi I really need some help here I have watched your video over over again how did you get linkage off colomn for steering angle sensor please help me out

Sveikas, pas mane pati juosta per trumpa, kad ir sulituota, susukus vaira iki galo ji vel nutruksta. Idomu, imanoma gauti pacia juosta ir pasikeisti, kad butu ilgesne ir nenutrukinetu susukus vaira iki galo?

i have exact same problem today

Bravoooooo,danke

Did it work on you?

Thanks that reale helped me 😅😅

Pytam o kolo zapasowe

Hello Tomas, can you please provide P/N for the part?

Ho questo problema Motore freddo parten subito Motore caldo fa molta fatica a partire Dopo 4 o 5 tentavi... Perché...?

Thanks you so much🙏🙏🙏

Qué le pasaba no entraba en modo deportivo?

Nu tu ir kiauras 😁

Thanks

👍👍👍👍👍👍👍

maybe Tesla too dirty it want to go to the sea and take shower!

hi friend can you help me I would like to understand how to deactivate the passenger side airbag of a Ford focus c max 2003 thanks for your help

Hey bro I got an 2014 audi Quattro I got the same exact problem how do I fix it it you don’t mind

Big thanks to Tomas a master of his craft, helped - solved my problem I highly recommend him

Thanks 😀

👌👌👌👌👌👌👌👌👌👌👌👌👌

i am doing it tomorrow too,.. using used epb unit. read eeprom st 95160 from my original car and copy files to the new used epb unit,.. i hope this will work the housing can be opened with constant heat and pressure. the RTV gets soft and the lid can be removed.

Thank you

Thanks so much.

Pouvez vous nous dire ou se trouve l'emplacement du bouchon de remplissage de l'huile de transmission? merci :)

Hi I have the same issue. I turned off it but the problem is the same 😢

Hi any ideas on how to get a circuit diagram for these ecus and how to read the ecu boot files

Может и не пропускать воздух, надо подключить диагностику и следить за долгосрочной коррекцией впрыска, когда поднимется заткнуть вентиль с лева палцем, если коррекция пойдет в низ, значит вентиль капут. Если не упадёт, смотреть клапан вентиляции картера, если всё нормально, посмотреть маленький клапан в впускном коллекторе, по середине гофрированный шланг снять и посмотреть. Если всё ок, надо проверять все вакуумные шланги.

Thank you

Perfekt, hat funktioniert. Danke 👍

Sveikas Tomai, Turiu tokia pačia problema 90DB, B4/2. Ar būtų galimybė kaip nors su tavimi susisiekti, atvažiuočiau išspręsti šita problema. Už pagalba atsilyginčiau.

For me helped hand brake reset. Just hold hand brake button for 5 seconds up, thant 5 s down. It was changed from manual to automatic hand brake release.

Where are the fuses for the electrical for lights inside and electric seat fuse?

Hi, I have the same problem when I go slowly it goes into protection. I changed everything and the car doesn't run. what could it be? thanks for your help, but if I go fast the problem doesn't appear. p0088

👍

Thanks it is work meg 1 fase 2 🎉

Sveikas tapati beda kaip tavo video ijungus D nieko nerodo kompa reikia irskot pagal koda ar gali skirtis kaskokios raides?

Nice work! I have exactly this clock spring, repaired it like you did in the video and now the steering wheel buttons work but now the servo is not working and orange light for steering and esc is now lit. The airbag lamp is still on but I suppose that needs to be reset by some other computer than I have. I did remove the screws underneath at the white part in the middle, could I have messed something up with that? Can you align that if you didnt mark it before disassembly? All the best! Daniel