- Видео 11
- Просмотров 40 024
R. SEA BOATS
Добавлен 30 мар 2018
Kids Jeep Wheel/Steering/Suspension Upgrade Fix
Any Bracket Or Pole, I used a Aluminum light Pole For Boats, squeezed each end to flat drilled a hole thru and put 10mm bolts and good as gold. just get it as close to front as possible when installing the steering won't be in the way and don't tighten too hard.
Просмотров: 22
Видео
10Ft 8" Seangles Dingy Boat/Inflatable New Review
Просмотров 6 тыс.2 года назад
10Ft 8" Seangles Dingy Boat/Inflatable New Review
2000-2007 Toyota Tundra Stereo Wiring
Просмотров 17 тыс.2 года назад
00-07 Toyota Tundra or Sequoia stereo Wiring
Yamaha 703 control bracket throttle fix pt2
Просмотров 1,9 тыс.3 года назад
Yamaha 703 control bracket throttle fix pt2
1996 Yamaha F50TLHU update to previous video throttle cable bracket
Просмотров 9053 года назад
in this video I just figured out after doing my research on what needs to be changed the bracket I will be describing in the video will come out in one piece and you will have to pretty much switch that C bracket to the other side.
05 jeep grand Cherokee Front Axle bushing how to
Просмотров 11 тыс.4 года назад
2005 jeep grand Cherokee front axle Bushing removal
I wish I could hug you. I wouldn’t have thought to do this!!!
Nice! What kind of fuel line is that
Mine did that. Wide open throttle on four blade prop for three hours it runs perfect now.
Perfect
Would you recommend this.
I just went through this. Seat the idle screws and turn them out 2 turns. Thats all i did, plus you need to get it in the water for a wide open clearout.
Check your compression mine did same thing and it was a broke ring in lower piston
The fuel/air mixture screws on the carbs needs to be removed and clean the seat of the screws, inspect the points on the screw if good then set at 2 and 1/4 turns from full seat of screw on each carb. With clean carbs should work good. If your 2 stroke oil in the tank is not fresh, remove and put fresh 2 stroke oil.
WHAT HP FOR THIS BOAT...
9.9 max I think
The front wheels aren't completely on the ramps and I don't see any wheel chalks in the back. 😬😬 That makes me super nervous.
Yeah I died that day. Said no more jeeps for me 😂
Hi What kind of pads were you going to get for the floor? Thanks
Just Amazon Floor foam Deck pads
What model, brand?
It's 10ft Not sure Model
Nice
Mines does this I need to figure it out
Hello, Is it ok to fish with 3 personns, i would like to buy this size but i m not certain about it. Thank you for your answer.
It's a little small for three people, but it can be done if you don't mind sitting close I'd imagine
What psi are you running?
No idea just pumped it up till it's solid
Did you ever figure it out mine is doing the same thing
Ended up selling it as is and got a four stroke 50 Yamaha
Did you figure yours out?
Mine was doing the same finally was problem from waters on second cylinder and ball bearing to up cylinder
Could also be reed valves
Excellent, Yeah pretty much the only one with the aluminum transom. Just wish they made a 12 or 14 ft. I will probably be going with this exact model myself. Thanks for posting it.
I trust you and don’t understand how or why all the others require the removal of the differential and CV joints. So much unnecessary work
How can I get a stripted 8mm bolt off
Depends we're it's located.
Thanks for the video, way easier than removing the whole differential!!!
This was perfect! The Grand failed state inspection for the differential mounts. It is the camping/trail rig so I wasn't about to spend the $700 Jeep wanted to do this job. I purchased poly mounts after watching this video and it saved me a ton of time and money!! Thank you!!
Hey did you have to drain the diff fluid? Will it leak if not? I'm looking to replace the bushings on my 05 jeep grand cherokee as they are worn out, also no stand needed for the differential? Did you just drive it on ramps and did it? Please help asap I need to get this car back on the road
Hey, pretty sure if you only swing the diff down like this guy shows you wont have to drain / refill the fluid.
@@fabiangarcia4230 thank you!! 🙂
No no fluids came out it's All sealed, there's just a round shaft sticking out where you unbolt the driveshaft ,the seal is behind it so it won't be in the way. You'd have to tear the diff apart to change the seal.
Check choke regulator?
Ended up selling it never got to it
did you ever figure this out?
Basically when I went to premix I disconnected the oil pump and I think the levers there pretty much needed to be adjusted or loosened I've never got to fixing it permanently ended up selling it the way it was
Right on! Thanks for the video and info! Doing an 08 GC!
Its pretty Simple, dont be scared to get in take the stuff out in order pry the sucker out, get a large C clamp or the one you can attach a drill or impact wrench and done deal, hurting the walls of the bushing wont hurt it as what matters is it sitting all the way and the rubber bushing doing its job.