Видео

That is an interesting idea

Thank you. I’ll get back to you shortly

🤣🤣🤣😂😂

It’s not a product I would recommend either, since I fixed this I’ve had a bunch more issues

​@@113Cyclesit's very disappointing, 6 months later I have to do the job again

Same here. I was expecting it to be quieter. I’m hopeful that once I figure out what I’m gonna do with the ceiling that it gets better

72 dollars to build on property I already own.

I didn’t build this one but I’m pretty sure the wheels came from Procycle.us I know they sell these same wheels.

Thank you. The only change I have made to it is to paint it Gray so it looks better on camera. Still works great

Absolutely

It’s not me and I agree

I would try Partzilla if yours is missing.

You can use the 3 inch on the sides. When you install them you can adjust the angle to the door. That’s what I did. I could have used the 2 inch but I wanted to make sure there would be no issues with the fit.

If it has good spark and it won’t run on a good propellant (I use starting fluid but brake clean should work as well) the next thing I would check is the air flow. I don’t work on 2 stokes that often so I would have to do some research on the testing the intake membrane to know how to do it. If your air cleaner is not blocked then I would check the timing after that.

Mini bikes are a great way learn basic. Good one you for that. I’m definitely not an expert with minibikes. This is the first one I built. That being said, you may have the engine idle set to high. That would cause the clutch to start engaging earlier than it should. Also, make sure that the clutch is oiled properly. I know that can cause a few issues Thank you for watching

That’s awesome. I’ve seen you posted some videos on it but I haven’t had the chance to watch them yet. I’m looking forward to it

Thank you and congratulations again on your victory

Thank you as always Tim.

Absolutely. I think I’m gonna try it myself next year

I’m going to Lamberts on Thursday next year. Not taking any chances

@@113Cycles lol I'll be there for sure. Can't believe I couldn't make it to this last one. Total bummer

I’m looking forward to next year already

It was a great time. You guys had some fast bikes. Made it even more fun

@@113Cycles Your bike was no slouch either! Can't wait till next year.

@@saltracer1 Thank you. Hopefully it will be even faster next year

Much appreciated

Thank you that’s great info to know. I always drain my carb bowls for any kind of storage. Always helps. Hopefully there will be peace soon

@@113Cycles Does running it dry, on choke for the last few minutes, drain the carb bowl?

@@jimmybrad156 I turn off the fuel valve and run the engine until it dies. You don't need to have the choke on. You could have the choke on. The Carb bowl will still run dry.

He puts on a great show

Mine is on a steel building as well. The PolyPro helped with the air coming in from the sides. I have the brush kit on the outside as well. between the two I don't have issues with dust. I have the brush kit on the outside top and sides.

@@113Cycles gotcha, I got mine on a well. The corners on the top seem to have a small gap no matter how much I adjust.

Wdym

@@SparkybearEngines that massive amount of torque..!

Yep, loads of torque. It's lots of fun to ride.

The studs on the bottom 8 feet were installed before the insulation was sprayed. I didn’t have the money to do all the studs at one time. I used metal L bracket with wood screws and wood to metal screw. Not a silly question at all. Hope this helps

Awesome, thank you

😂🤣

Gotta be prepared right 🤣

I have the 19 inch front wheel that was stock and a 17 inch excel supermoto wheel

It’s a 1 inch x 2 inch

Will do. Thank you

Thank you I had a great time

Thank you sir

I did. I messed tech by just a little bit though. I’ll have to wait in inline tomorrow.

Thank you so much 😀

Sucks you’re not gonna make it. We’ll all have a great time for you

🤣🤣 Good one

I have faith in ya

@@mmotorcycles9497 Thank you

It’s not a big deal. Check your service manual or look up a parts diagram online. You can just it back in the way it came out and you should be good to go.

I love this body style

I love it

Yes it was.

Honestly I don’t really know. I’ve seen other people do it this way and I just went with it. It works great.

Yes your right ..

Thanks for watching

Sorry for the last response. The exhaust fan I used is a iLiving 12” exhaust fan that I bought from Amazon. The controller went out a few months ago. I replaced the the controller and it’s good to go again. Good luck with your shop and thank you for watching

I always do

@@113Cycles thanks. I got a 12in grom tire and the last two times iv had hell with it. Was up all night beating on it, carb cleaner didnt have enough PoP

I had the same problem recently. I tried all sorts of sprays in the shop and nothing had enough pop. I'm looking for something else to use now. This is my go to for seating beads

Google translate isn’t doing the best job here. From what I can read. If you are showing full even with just 3 liters of oil. Then I think you’re good to go. You may not have gotten all the oil out or maybe filter wasn’t changed. Thank you for watching

I don’t ride on the roads, it’s not street legal. Just at the track and the occasional parking lot for tuning. It sticks great.

👍👍👍