Видео

Error 27..... spindle off calibration. Im curious 🤔 in the error 34. We didn't think error 32 to Error 39 exist.

ruclips.net/video/QVAy6acxL9I/видео.htmlsi=GR2SGOxvPppiC2Sq

I followed this guide, only 1 out of 3 drives would read properly. I did the "line up all 3 metal notches then tighten spindle facing backward" alignment and so far 2 out of 2 worked. It's the same as turning the large gear clockwise until the head snaps back, then turn it counter clockwise a little to make sure you're at the end, you'll feel strong resistance, then align the spindle towards the back. It's interesting that the alignment between the 2 methods are so different, yet it still works for some drives. Excellent illustration of the belt and how to reinstall the bottom piece though, very informative. Used twist ties instead of tape to hold the belt.

Super! Les images du schéma, style SFC, sont très bine fait e et très utile 👍

It sucks Nintendo designed the fds the way they did, in the future players will have to figure out how to replace the belt when it breaks with what’s available.

Still getting error 22 after doing this! Any help would be appreciated! Even then my belt still keeps slipping upward when the drive runs….

Thank you for posting this guide. Worked great! The trickiest part for me was getting the spindle plate removed. I still don't really understand how I did it. Oddly, placing it back on was easier.

At around 25min in you show the triangle and cog, how to line it up. Were there two types of wheels within those? Mine is a little rectangle I got in the mail yesterday, tehre is no circle I've spun it around enough to know. Also I could never un-latch the triangle, not sure what you were on about it doesn't come off on mine so I threaded the belt under fine. Mine simply just popped, no mess no gooey bits (still cleaned it) and now it does and doesn't work. Before it was just spinning free, now I'm at err 22. I tried the whole line the 'circle' up and use the tool to loosen the spindle and line it up and it just didn't work.

Anyone still get Error 22 after following all of the steps in the video? Any advice would be appreciated

Не нужно там столько разбирать. Много лишних операций.

Super demonstration and explanation. You made it look easy.

This probably the best tutorial I have ever followed! Thank you very much. Out of the six discs I own only one I can’t get to work. The metal piece on my spindle didn’t have the hole. I took a picture it looks different from yours

I owe you a pint sir. Thank you

Easily the best and most in-depth tutorial on this procedure. A perfect choice for your channel’s debut.

Hadn't switched a belt in a famicom disk in ages, memory was hazy. Followed yohr guide and it worked flawlessly on my newly aquired Twin Famicom.

8 years later and this video is still helping people like me. Thank you. Got my drive calibrated and games are working great.

Just wanted to say Thank You! This was my first belt replacement attempt on a model that had already had it replaced, so I didn't know what to expect. Old belt was yellowed and much larger so I think it was a slipping/tension issue, but your guide got me through! I didn't have immediate success but your "visual landmark" approach got me very close, and after dialing it in I think it loads games faster than it did when it first arrived from Kanagawa, Japan! I also realized I've bought a few FDS games from your store back in 2019, so thank you for once again being a part of my FDS adventure! 😄

Someone get this man a beer, he’s a genius! Great tutorial, easy to follow, works a charm. Must have been designed like that from the start. I can’t see them ripping drives apart and fiddling with the spindles for hours on the production line and repair centres. Quick and easy. Thanks!

This method worked at first but then my drive stopped working after a few minutes of testing and now i can't get it to read any game and get's err 27

Thanks - just replaced the belt with your help!

I have done it nice and at the first try with your tutorial. Thanks a lot! It is explained perfectly. After the belt replacement, I just had to calibrate a bit the motor and the reader screw, but I achieved it in an hour approx. 3 games working perfectly! Thanks!!!

Hi I have tried your method of re calibrating the spindle but am still getting error 22. I have also tried using other methods on other videos but still getting error 22 or error 21. Any help would be appreciated. Thanks in advance

I’m so done this twin fami was the wrong thing to buy

Thank you!

This method did not work for me. I too have a square hole in the gear. I also tried the method of removing the disk carrier and rotating for the mechanical click method without success. At this point I figured it was just something I had done incorrectly since one of these methods should have worked. I tested various positions of the gear. With the black square at the 5:00 position, the drive read a factory disk, a re-written disk as well as a disk with a Game Doctor. I hope this helps someone. Could just be dumb luck.

Делал в первый раз, согласно видеоинструкции, все запустилось с первой попытки. Благодарю!

Worked like a charm. Thanks so much for this. A couple changes/notes from my experience: - I didn't bother with the cables, i just lifted the circuit board out of the way enough once the screws were removed. - my replacement belts were too small to tape together like that so I just let it sit in roughly the right spot with no issues. - In my initial post repair tests, the system looped infinitely trying to read the disk w/o any error codes. it turned out the black toggle switch the read head slides back and hits wasn't getting triggered. Not sure why this was happening but after sliding the read head back and forth and toggling that switch manually several times, it started giving me the read errors I expected.

Man, you are a legend! These instructions are perfect and your method is flawless, thank you so much for this. I followed your guide and it didn't work at first but I found it had nothing to do with alignment. I had placed the belt on straight but at some point of the big pulley's course, it must have been slightly offset vertically and it was causing the belt to slip out of the golden pulley. Once I ran it by hand a couple of times to fix that, I turned on the console tried a disk and it instantly loaded very quickly, works with all games I've tried. Many, many thanks for sharing this.

Are there any uptdates to this project?

thats alot of job for the easiest way to replace those belts. why they made it so hard to replace a damn belt ? not smart. they should have made it eqasily accessible with only a few screws to remove. not having to disassemble the whole thing. those belts also seem to fail miserably often. they put such a cheap belt in there. i never had a single pc drive or even other drives fail on me in all my life.

Great tutorial, i just replaced the belt and bring back to live a famicom disk system and works perfectly fine with disks written on my twin famicom

Fantastic tutorial! This wasn't my first time replacing a belt, but thanks to you, it's been the easiest! Thank you so much!

I've tried this method twice and it didn't work for me. Made sure the cog was lined up in the correct spot. Made sure the spindle was facing outward and tightened. The first one kept giving an error 27 message. Second time the drive just keeps spinning and clicking.

Thanks alot! was a bit worried since This was the first time i would try but it all went great, didn't even have to calibrate since it just lined up perfectly from start. very nicely done with all the explanations and pictures to show directions.

I've been trying to find it locally but no to avail. Saw your ebay ad but it said there you dont't ship to my country. Can you ship to the philippines?

Commenting to update the last known date of a viewer... lol I just ordered my first Japanese system a Famicom and the Disk System ..!

wow great video. Actually I have constantly error 21, 22 y 27 and I will try this method. also, I have another issue: passing arround 6 second, my screen is turning a wrong images and dark. This fault it´s appear after of connect a power supply with inverted polarity. I think that is a RAM damage or a condensator.

If Subaru made it, it would be chain driven.

That is going to feel amazing if you can pull it off!

Thank you, good tutorial and my Famicom Disk System is now fixed :)

This is sooo good!!!

はじめましてこんにちは😃 また見にきますね👍

I don’t know if you still check these, but my FDS half worked before I loosened and retightened the spindle. I did everything identically to your process, with the only difference being that mine doesn’t have the hole in the metal cover. I’d appreciate any help, but I’ll probably manage if not. Thanks!

When will your store reopen? I badly need some replacement FDS belts!

I took the whole drive appart and now the hole in the white plastic doesnt line up with where it was from the factory ! Is there a way to "recalibrate it" ? As I have been sitting over 7 hours at this drive allready :(

This tutorial makes belt replacement so much easier. Thanks a lot man!

looks absolutely stunning! Hope to see your website come back up whenever japan's shipping internationally get sorted out, I got my FDS belt from your store!

This looks incredibly fun

This looks great!

I like it!