Видео

Hi, thanks for the video, any advice, my pump seems to go for couple of secs then says EO2, much appreciated

Thanks

What if this doesn’t fix the problem…? Impeller magnet was split open the length of the magnet! Thought for sure that was what it would need. Going to start opening it up again and maybe the pump gasket which was about a mm or 2 too long is causing the problem. Pressure switch available ?

My RCD doesn't work anymore

How do I order a replacement impeller. Thank you

Either Ive done this completely wrong or it was never an impeller problem 😕 follows the video step by step but it hasn’t worked for me 🙁

Thanks Dave. Spent hours trying to do it the way the manufacturer video shows you without success. Used your method (I used a table knife) so easy. 👍

I am so grateful for you taking the time to make this video! Our hot tub wouldn’t start up this week when we got it out for the summer, we were worried we’d need a whole new ‘egg’ but this video has meant I’ve been able to fix it in minutes for a fraction of the price! Weirdly our plastic bit wasn’t broken, but the replacement impeller worked so something must have been up 😂😂

Brilliant instructions! Received my replacement impeller in the post today, fitted it and low and behold the hot tub is working again!! So very pleased! The part I removed was definitely gone - completely split and rusted. Thanks so much 👍😁

Dave many thanks your suggested fix worked well amazing thanks.

Guys. I have had recent issues with the E02 code on Saluspa. Even though I replaced with a new cartridge, E02 still appeared. Then this: ONE ONLY NEEDS TO PUSH THE LOCK BUTTON TO RESET EVERYTHING. Don't need to repair anything. Company won't tell you this. They just want to sell you another spa.

Thanks from New Zealand. We bought the new impeller and installed it following your very clear and concise instructions. Our spa is currently reheating and I'm looking forward to getting in! Thanks

Never use Vaseline as it rots the rubber seal, use silicon grease

Good thinking!

Is this possible for an e6 temp fault on wave hot tub

hi Dave,,,,know anything about the Heater ? when I press my heater button on a Miami it trips out my elec supply ?

Perfect thank you for this I thought I was going to have to but a new pump completely. Top fella

I just bought one first pump saluspa cup holder one got error EO2 got the next pump egg one same thing do you think both could be broken like that?? They are sending me a third…. So instead of throwing them out maybe I could buy this well 2 kits !

Absolute Legend!! Many thanks 👍

Great video thanks. I've got a customer's heating trip the mains when turned on any suggestions?

I have changed the impeller and the flow sensor (entire pipe including sensor) but still running in E02. Any thoughts?

Thank you for this video - it helped me tremendously! In my case nothing broke inside the pump - it just became too entangled in some hair to move correctly. Thanks again!

Thanks I had the same problem, but after watching your clip I changed the O-rings at pump connection and the problem was solved. 🌞

Do you have a link to the impeller?

How do I get the parts

Your a rockstar Thank you for the amazing video Just like you said my shaft cracked Stay happy healthy and fluid

Thank you very much for the video. fixed my E02 error. Impeller shaft was split open and corroded.

I have replaced the impeller (very proud of myself) thank you

Dave just watched your video, ordered the part it came today, took me about 5 minutes to do! Used Vicks vapour rub too as it was all I had! Many thanks👍

Where do you get the impeller?

thanks for the tutorial where do i get the new impellor shaft from

Hi Dave do you sell the seals and propeller? If so where can I buy them (rather than get the wrong bits off eBay..) and would you recommend a metal stick in the middle or another plastic stick? Thanks

Where can I get a new impeller

Is it normal for impeller to break only after 6 weeks?

Would like to say thanks for this video and kit my lay z spa is now repaired and silent 👍

Hi Dave mate I changed my impeller due to old one cracked , I turn the new one on spins for 3 seconds then cuts out again , any ideas pal ,cheers

I have flow in out of egg. But when I turn heater on it stays on for 20 or so secs then cuts out. Eo2 error has been playing up on and off for months. Could this be the impeller also??

How can I tell if it's bad it looks ok

Thanks Dave for the great film, followed your instructions and now my spa pumps fixed!

Hi Dave love your videos can you tell me what size is the impeller for a lazy spa vegas please as I have an e02 error and need a new one or can you supply me with one

Hey dave, I followed your instructions and found it relatively easy to do. It seems to have sorted out the error 2 problem I had. Thank you so much for this video. It has saved me a right headache and money which I don't really have to buy a new one, and it is absolutely much quieter. You sir, I salute you, legend. 👍 Cheers... gaz

Awesome cheers 👍🍻👍👍👍

Is there a link to buy the parts from you?

How do I buy one of these from you please

Hi Dave, thanks for the advice, I am just about to strip down my pump, do you still sell the spare impeller & is so how do I get one from you please?

Perfect repair, it works great 👌🏻😎

so got the dreaded E-02 done all the usual quick fixes including a descale fitted new seals etc but same issue after running it for about 10 mins where can I get the replacement impeller parts from ?

Thanks for the Video Dave! I have a HydroJet pump, slightly different to pull apart, but it fixed my E02 error! Wouldn't have given it a go without watching this as I am a DIY disaster. I ordered the new impeller from the link in the comments. The impeller wasn't broken, but was clearly worn in places and had discoloured due to the heat. Swapped it out and all good! Thanks!

Any other thoughts what it could be?..filters etc fine impellor replaced and still no luck

Hi how can I order this part plz