Видео

Yes, that cylinder was full of fuel and smoke from exhaust tail pipe

@mathewweavers4475 Yeah, it's a very big job, but you can do it 💪

Sorry, I don't have the full video, but I think the only thing to open is the finder liner and one small panel around the coolant cap.

Yes Please

Yeah, I think it is cause by dirty engine oil . Because it will block the strainer from getting enough oil . Also, when you scan your car and you have p0341. Camshaft position sensor range/or performance. I recommend you change it. 👍

@@yutaka-y4o 😆 🤣

@patrickwaweru6589 ok, sorry for that. If you have this code, then you need to replace the engine oil pump solenoid valve and its wire connector. You need to remove the oil sump to be able to replace it. Mostly, it is the wire connector from the sump to outside the socket, the one I was checking Thanks 😊 👍

@@stevoautohelp this is for 3.0t/3.7 right I have a q50 2.0t from the specs it has no oil pressure sensor rather a oil switch level and I have code

Sorry, but after those two locks, that's it . Then you can remove 😊

@@stevoautohelp thx

No you cant​@@stevoautohelp

It's not that easy. You need to hold very tight . I recommend using q hook or a screwdriver 🪛 that will be the best 👌

It's V8 engine 5.7

Ok, actually, the customer brought it from the dealer. He told us he had one defective ultrasound sensor, so he bought all sensors, including the speed sensor. And it was the hardest work I have ever done.

😊 I will be grad ✨️

24,000 to 30,000 miles is the normal range. But if you have sudden overheating and the temperature is going higher than before, I recommend you replace it and make sure there is no leak. 😊

😆 that will be like double trouble cus the condition is very bad

You're welcome 😊

😆 🤣

Hello 👋 Please, is there an engine light on if on? Then check it and tell me, or if there's none, then I suggest you check the catalytic converter if blocked 🚫 like removing the oxygen sensor before the catalytic converter and go test drive to see different let me know after Thanks 😊 👍

@stevoautohelp Hi brother firstly thank you for replying to my message... The check engine just started yesterday .. before the check engine start i took the car to the dealer they said the car just needs programming ,, so they did and the problem remain the same plus check engine now 🙂 ....

Hi, sorry I had data issues Please can you tell me the engine light code so I can start from there better😊

@stevoautohelp not sure why youtube didn't inform me about your reply .. the codes as below boss ..

@stevoautohelp P014E [0x014E] Heated oxygen sensor (HO2S) 1, bank 2 - slow response rich to lean Status: Confirmed ---------------------------- P014E(00) [0x014E00] Archive (inactive) Heated oxygen sensor (HO2S) 1, bank 2 - slow response rich to lean Status: Confirmed, Test not completed during this operation cycle ============================ Engine control unitEngine control unit DTCs: 1

Sorry I haven't removed some before 😊

Quality City Garage at Hamadtown, Bahrain 🇧🇭

Please can you ask again cus I don't understand your question properly 🙏

Comment activer ( afficher ) température moteur dans le tableau de bord

Please go to the engine live data or data stream. You will find mixture enter there, and you will find engine coolant temperature readings there. Thank you. I hope I help. Just let me know afterwards. Thanks

Which one, please, cus I was speaking some English but not that correct like the UK and Americans is African English 🤔 thank you

Am in Bahrain, Hamadtown Number 33515725

@@stevoautohelp mashalla you are doctor😂 very nice work brother