- Видео 143
- Просмотров 229 328
Woody w
Добавлен 23 июл 2013
AN hose fitting installed with less stress.
My approach to installing AN hose fittings using a hose clamp to assist cutting stainless steel braid hose
Просмотров: 1 078
Видео
How to make adjusting coil slugs way less difficult.
Просмотров 1562 месяца назад
Using a pair of 6x32" nuts fastened to the COILS shaft, makes turning the slug is easier physically and I don't keep slipping out of tiny slot. A 5/16" nut driver slips over the nut with a captive washer and makes adjustment far less difficult. A pair of nuts jammed together hold the shaft, removing the tedious task of trying to turn that tiny slotted shaft. The bigger nut driver handle also re...
local 80m noise vs preselector
Просмотров 1368 месяцев назад
7300 noise on 860 ft. loop 2pm 2/29/2024 with n without mfj1040c.
toy cat snake does not seem to be working, just goes in circle...
Просмотров 959 месяцев назад
toy cat snake does not seem to be working, just goes in circle...
Running nut control n auto reverse, no binding.
Просмотров 175Год назад
running nut without binding/ jambing using nuts with limiters
Testing auto-reverse on magnetic loop tuner drive motor
Просмотров 110Год назад
Drag on RUNNING NUT causes a false reversal, nylon washers and metal washers failed to release smoothly. Have ordered 1/4" roller bearing thrust washers that should solve stiction-drag issues. Enjoy WW
Getting my. JOHNSON DESK KW UP ON MY WORK BENCH, 450#
Просмотров 325Год назад
I had been looking for the grand prise, a desk kw by JOHNSON to fill out my operating and restored and painted rigs. Took a 38 hour door to door drive to Wisconsin from Manassas Va, 1900 miles to pickup / purchase it !. Getting the desk inside was ezey peezy, took my car lift to off load the power supply unit into a lawn cart and then an appliance dolly to bring it in. I will be checked out wir...
Diagnosing a ALS500M amp that i returned under warranty, it was sent back : as no problems found.
Просмотров 423Год назад
Diagnosing a ALS500M amp that i returned under warranty, it was sent back : as no problems found.
Restoring an invader 2000 chassis finish, with a bit of brushing and spray paint.
Просмотров 175Год назад
Restoring an invader 2000 chassis finish, with a bit of brushing and spray paint.
An easy to make mobile work bench for working on old radios or other hobbies
Просмотров 191Год назад
An easy to make mobile work bench for working on old radios or other hobbies
Valiant transmitter refitted and repainted
Просмотров 152Год назад
Valiant transmitter refitted and repainted
Increased carrier modulation on a Johnson 500 with one small part.
Просмотров 1682 года назад
Increased carrier modulation on a Johnson 500 with one small part.
Testing Johnson 500 on bench with negative plate clamp installed
Просмотров 572 года назад
Testing Johnson 500 on bench with negative plate clamp installed
Johnson 500 repainted and refurbished, better than new.
Просмотров 3822 года назад
Johnson 500 repainted and refurbished, better than new.
hex beam on a fold over mast on a tilt over tower.
Просмотров 4292 года назад
hex beam on a fold over mast on a tilt over tower.
My hex beam on a "stick" mast for better support and fold over capabilities.
Просмотров 1,1 тыс.2 года назад
My hex beam on a "stick" mast for better support and fold over capabilities.
Polishing radio knobs (Johnson radio shown) easily.
Просмотров 1432 года назад
Polishing radio knobs (Johnson radio shown) easily.
Tilt over MAST for my diy tilt over tower -crank up mast , HEX ANTENNA.
Просмотров 6992 года назад
Tilt over MAST for my diy tilt over tower -crank up mast , HEX ANTENNA.
Mag loop trimmer capacitor to allow 40m operation.
Просмотров 5212 года назад
Mag loop trimmer capacitor to allow 40m operation.
rig blaster audio issue on separate xmitter and receiver....boat anchor station.
Просмотров 372 года назад
rig blaster audio issue on separate xmitter and receiver....boat anchor station.
Tuning my Johnson Invader 2000 electronically with my huff- n- puff circuit.
Просмотров 832 года назад
Tuning my Johnson Invader 2000 electronically with my huff- n- puff circuit.
huff n puff oscillator stability checkout.
Просмотров 632 года назад
huff n puff oscillator stability checkout.
Huff and puff ckt added to my INVADER 2000 for stability
Просмотров 1182 года назад
Huff and puff ckt added to my INVADER 2000 for stability
INVADER 2000 Stable operation after parts are all back together
Просмотров 412 года назад
INVADER 2000 Stable operation after parts are all back together
Tilt over hex beam on 53' crank up tilt mast i designed. part #3
Просмотров 1,7 тыс.2 года назад
Tilt over hex beam on 53' crank up tilt mast i designed. part #3