Видео

Hello, Write me an email through the site: www.electrondigit.com/

Hello, Please give me a photo of the controller connection.. What is the supply voltage of the controller?

@@juryshef I am having the same issue. Was this ever resolved?

@@LoganYoung-n8v Hi, Please give me a photo of the controller connection and strip.

@@juryshef I can't link photos on youtube, but the controller is a AN6USPI0 with a green mother board running off a 5v power supply connected to an LED WS2811 Strip light.

@@LoganYoung-n8v Visit to my website and write to the email with a photo. www.electrondigit.com/

Yes of course. ruclips.net/video/eKwgl7UFZzA/видео.html

@@juryshef So I'm interested in what type of LED Stripes this is, how you have solved the power supply, how big the individual panels are, which carrier material was used and whether you have the power supply and controller mounted directly to the panels or have seperat... Thanks for answering

@@dvrsoftware425 , You can order a similar screen. The contact is listed above. The panel contains 6 modules of 13 x 13 led (one universe). Each module is connected to one port of the controller. The module is connected to a 12 amp 5 volt power supply. 60 watts per module. 360 watts per panel. You can use sealed pixels.

@@juryshef and are the power supplies mounted onto the panels? Or how you can get 12A @5V over distance?

@@dvrsoftware425, each module has a power supply. Each panel has 6 power supply units and one controller artnet + pixels www.ebay.com/itm/264305634906.

Give me a link to the strip. Do you mean strip with TTL input? You can connect TTL input to B(D-) terminal.

DMX and SPI(one wire or two wires) - this is different physical interfaces. The firmware replacing will not change this.

Yes. You can see in this video: 3:20. you can connect for example: freestyler -> controller(port5 output)->controller(Port4 input) -> Madrix input. ruclips.net/video/5WqYAenkV-o/видео.html

Yes of course. This controller can work as a DMX to SPI decoder. You can also see these controllers: www.ebay.com/itm/321934091091 www.ebay.com/itm/221548869762

Ok thanks. Can this be driven by FreeStyler to address each pixel? Do you have some overview/video of how this is setup in FreeStyler?

Which DMX controller do you have?

I have a WS24LU3A 24ch DMX512 decoder RGB from a while back

Ok, you need to configure the freestyler for your decoder and connect the controller according to the instructions on the ebay page.

What is the state of the SD and Art-Net LEDs?

I install the fimware, but the rj45 does not recognize me, the card does not enter by network, I need help or to be able to buy another one for ebay I am using it in an important project, I need your help yury

I download the fimware, I do the video steps and nothing does not record the sd in the micro, buy it a while ago by ebay, but I have not used it stopped the rj45, the sd led flashes and the led, artnet does not light

Format the card in fat32, input the iso file and the folder with the codes but do not take the port rj45

Write me please to ebay or to gmail. 1. Which controller do you use? SPI or DMX? 2. What is the supply voltage? 3. What is the state of the rj45 LEDs? 4. Do you connect to the computer or the switch? Please write by email. It will be faster.

What is the length of the input packet. It should be 512 bytes. If the length is less than I'll give you the firmware for the setting of this parameter.

If you have access to the controller web page, the problems can not be. This configuration problem.

This DMX console can control only 192 channels. But it would still have a standardized DMX512 with 512 bytes send, right? I have access to the Webpage. I set the Controller to the IP 192.168.2.2, The Virtual IP to 192.168.2.3 and the IP of the Computer to 192.168.2.100, if this informations helps you. I also tried it with 2.0.0.2, 2.0.0.3 and 2.0.0.100.

I'm not sure. You should check the console documentation. I think there are only 192 channels. You must set: Input to IP: 192.168.2.100 "On" (send as unicast to PC) and input data size should be 512 channel. You can change firmware and set the 192 channels length of input: www.electronpoint.com/artnet6_00/img_asn_08_07_14_ralf.zip

Thank you! Now the controller works perfectly!

Hello, pls. write me an email. What software do you use?

arnet card 6 un - arrives in Chile. connected via ethernet, I need to know if the DMX signal is for teams of 12 or more channels , freestyler Chile sent a Blast but control on ebay image shows a loop RJ45 DMX, Current transition moving heads and not led www.ebay.com/itm/DMX-512-controller-Art-Net-E1-31-ACN-six-output-input-ports-ArtNet-Ethernet-/321556994192?pt=LH_DefaultDomain_0&hash=item4ade4a5890 Network to DMX controller. (DMX 512) or only 3 channels ?????????????? Six DMX ports .-- (ok) Art-Net III support (unicast and broadcast). (Ok) E1.31 (sACN) multicast network protocol. (Ok) Works with all Art-Net and sACN compatible software, Both free & commercial. (FreeStyler, Madrix, Jinx, LoR (E1.31) ..........) moves 12-channel moving head ??????????????? Up to 6 output or up to 6 DMX 512 input ports. ????????????? Management web server settings for the controller. (Ok) 10/100 Ethernet port. (Ok) 7V-24V power supply. (Ok) ARM 32 CPU (ok) Size: 145 x 90 x 50 mm. Weight: 170 grams. Installation on 35 mm DIN rail. ok Art-Net, E1.31 compatible software. FreeStyler, Madrix, Jinx, ... (ok) Supports firmware upgrade. (Ok)

tulioagustin tapia

Yes of course. 512 channels per port. I wrote a letter to your email.

agustin_chandia@hotmail.com

better use this: www.ebay.com/itm/221299388963