- Видео 71
- Просмотров 172 109
Andrew Barton Laundry
Добавлен 12 ноя 2015
Видео
Laundromat Equipment Speed Queen Quantum Gold Solution
Просмотров 9909 лет назад
Laundromat Equipment Speed Queen Quantum Gold Solution
Speed Queen Top Load Electric Controls 1
Просмотров 899 лет назад
Speed Queen Top Load Electric Controls 1
Pocket Hardmount Washer Extractor Preventative Maintenance
Просмотров 4,7 тыс.9 лет назад
Pocket Hardmount Washer Extractor Preventative Maintenance
Pocket Hardmount Washer Extractor Removal
Просмотров 3049 лет назад
Pocket Hardmount Washer Extractor Removal
Pocket Hardmount Washer Extractor UW Installation
Просмотров 9 тыс.9 лет назад
Pocket Hardmount Washer Extractor UW Installation
Pocket Hardmount Washer Extractor UW Bearing Replacement
Просмотров 37 тыс.9 лет назад
Pocket Hardmount Washer Extractor UW Bearing Replacement
Softmount Washer Extractor Preventative Maintenance
Просмотров 1,1 тыс.9 лет назад
Softmount Washer Extractor Preventative Maintenance
Softmount Washer Extractor Bearing Replacement
Просмотров 9 тыс.9 лет назад
Softmount Washer Extractor Bearing Replacement
Do u have the parts numbers
Water level too low to get clean. Should be a 1/3 high to just below half.
ALRIGHT I FOUND MY NOISE! THANK YOU, THERE WAS A WASH CLOTH STUCK BEHIND TE TUB SEAL
My laundries ain't that easy to change stuff out I just don't have the space one reason is is because of property tax
Great sir
Put the washer with screen in wrong lol... I have been in the line of work my whole life... I get to install a whole new laundry this wk... Joy joy lol
nice job🙂
Wait a minute I’ve seen these horizons at a laundromat and I thought it automatically chooses the spin speed by how much is in there I washed a load In a horizon on cold temperature and I got a 500 RPM spin cycle and my clothes were still wet
How do I remove a screw that is in between the drums?
working in this industry for 27 years started off on these things thank fuk they moved on,rebars were a nitemare and washer in general ahhhhhhhhhhh
Great video
Nice and easy when machine done no hours and nothing siezed or rusted,greetings from Australia worked on these cement mixers 27 years ago,never again
Thanks for sharing these videos. They're very useful!
It's a very well done and informative video. It leaves out removal of the basket shaft if it is rusted to the bearings. I've had bearings explode when puller pressure was applied leaving the inner race stuck on the shaft. Cutting with a die grinder and diamond wheel seems to be the only way.
EXCELENTE JOB...MY FRIEND...GREETINGS FROM CUERNAVACA.MORELOS..MÉXICO
Nice video.. I have a question.. What do I do with a washer that does not seam to have any zert fittings and no simple way of greasing the bearings.. I have 2 unimac next to each other.. one has the grease fittings in the standard spo. ( To the left of control panel on outer shell). The other is a little older and no visible way of lubing...I've climbed over the machine for weeks..torn it half way apart..so confused here..was tossed into this job and never giving the heads up on anything cause they fired the last guy a month before I started.
There's nothing you can do short of replacing the bearings. For a short time years ago on some of the older model machines Unimac used a bearing that had no grease fittings. Then they once again started using a bearing that could be greased. I've done many, many bearing jobs on these machines over the last 40 years. I just did a bearing job on a 1994 Unimac washer yesterday and it had the original old style bearing and no way of greasing it. The new bearings come with push to connect fittings for 1/4" tubing. If you replace the bearings you will need to order the remote grease kit that mounts onto the machine to the left of the control panel separately. Hope this helps.
Usually those sealed bearings need replacement. I've been in similar circumstances where bearing made noise but were not worn and the basket had no axial play. If you're in a jam a temporary measure would be to get a grease gun with a needle applicator, and inject grease (type #3) between the bearing shield and race -- being careful not to damage or pop the shield out. It's bending the rules, so plan on replacement as soon as practical.
I'm trying to remove basket from shaft of 12 year old machine. Ram is at 8000psi and it's not budging.
What kind of jacks are those
Well done
Tuipomnbb
Is there a video on how to replace the barrings on a 25 lb unimac washer extractor ? Can't find anything Please help
Very confusing