Видео

did you end up hardening it? that finish needs to be protected.

Hey that spot welding worked out good! Please do another video on it explaining it or expanding on the concept!

Drill bits aren't the greatest thing to make precision round holes. A quality mag drill with angular cutters and built in lubrication system would cut your time in half and make more precise holes.

How far was your tungsten?

Man I'd buy one of those trays from you. I have the same HF press... so awesome

What did they charge to surface grind your top

Where did you get the fixture table?

Great overview video of the improvements. 👍 #5 was my favorite, The tool holder tip would save time on setup.

Great Idea Bob had. 👍 Thanks for Sharing.

Bla bla bla bla bla !!!

Two words, Annular cutter.

Could you please share again what would be your recommended size for the plate?

Are you sure this was just 1/4 thick? Looks so thick :)

I have that cart under my laser. If I touch the cart, it moves and wrecks my project. Now I'm looking at putting blocks under the cart to stabilize it. A two wheeled cart seems better, but I committed already.

Is from this game ATV Offroad Fury 2

I totally dig the effort, I too build as much as I can, that’s a table you would never part with, it’s personal. However, understanding the value in a bought table is apparent after seeing your effort. Good stuff!

I think Id just buy the Fireball tool Dragon wagon. This is too much work.

So helpful if you link where you bought things.

I’d like to see how the clamps work in the holes, is there a video on them? What are they called?

This is amazing. Can you help me find the fume extractor and the black piece that connects to it?

I didnt go near as extravagant. I just drilled 4 dowel centering holes in the original plates.

great vid! im looking to get that exact same laser can you make a review please?!(:

Sensacional!! Parabéns 🤜🤛🇧🇷

Appreciate how u focus on what makes you happy!

This is two years old so I'm fairly sure someone has said this already but, an annular cutter would have cut hours out of this job.

I just went to NUB tools and nothing found under the 20 ton press page. Disappointing

Excellent build. I seen spot welds done by both MIG and TIG tons of times but this was the best result yet. Have you thought about grinding a small notch on the rim of the cup for spot welding? May help hot gasses escape or maybe not a good idea? I seen your settings listed but what diameter electrode and how was it prepared (blunt, pointed etc)? Greatly appreciate any feedback!!!!. Cheers

What? no God awful music? Much prefer without. Excellent work!!!!

You have some impressive skills and tools in your shop!!!

Cool ! I enjoyed that . Thanks . 👊🏼🔥

I can't find this valve spring compressor in stock anywhere.

I love your tool room lathe . :)

Well, you don't have to use it, you can always take it to the trade shows, car shows or something . lol

Very nice work! I am looking at doing the same thing and have a few questions. Did you go with removable bushings over press fit to save money? I can see having to switch out the bushing between holes adding a lot of time. Did you use bushings 3/4" long or less to create chip clearance? Was there a reason you used a drill bit and reamer over a annual cutter? Thank you for your time

What he did was a waist of time. That mag base drill has HSS drill bits that cut out perfect holes. They cut the out side diameter and leave behind a center slub the spring pushes oh after the cut.

Send Camp Italy and england so much Build Cars fomula so table strongs , themes top gear so table top again 😊

as i saw your set up i knew you were a dirty Tigger LOL. Nice set up bro.

Did i see right that you tig welded without a gaslens at the beginning? Never thoght of trying that:) Nice job on the table!

use a magnet. no drill no thrill

what a waste of a good peace of iron

That is a lot of work, Impressive. When you get 1st dent going to be tough. 2nd one not so bad.

Very nice. Oddly, my HF 20 ton press stud is 1.915” diameter. I decided to leave that and make a removable piece to fit over it out of 2.250” dia 1144. So everything fits on that. Also I get the point of press pins as I’ve done that too. But I found that I needed to use hardened pins for them instead of just machining the ends down as that tends to mushroom too easily. So I just pressed the pins into the pieces that fit in the end of the adapter I made. Nice handle holder. I didn’t think of making it that way. Instead, I welded two 0.750 x 1” tabs onto the bottom edge of the beam and put thin rubber there for the long and short handles. I like that bottom tray. I never go down that far with the press, so I’m thinking of making one for the fingers of my SwagoffRoad finger break. I never know where to put these things.

Cooool just bought this same cart for my fiber laser, I was a bit worried the power unit wouldn't fit below, but with the drawer out it can slide right in! I might have to borrow some of your ideas

Great job, and great video!👍🏻

I really want a table like this, but first i gonna build myself a cnc machine to do that for me. I am lazy.

Very nice, great job!👍🏻

Nice job what’s the price on that tool cabinet approximately for them to make that?

Kool shop. Nice to see a true machinist make one of these. A lot of hacks out there. I’ve been a toolmaker/fabricator for 50+ years. Certainly over kill using a CNC but hey like you said, SATISFACTION. Love the Monarch, one of the best lathes out there. And a nice Doosan lathe. My sons bought my CNC machine shop several years ago. Two years ago they bought one of them. Quite happy with it. Majority of our lathes are Miyano which are very good but DN Solutions (was Doosan and Daewoo prior) are building great machines at reasonable prices. BTW your Tig Is extremely good. Nice video too. In fact I’ll subscribe , nice to watch someone who gets it

TIL spot welding with tig is a thing